Laurence reports:

"Kernel >5.18 on Zaurus has a bug where the power management code can't
talk to devices, emitting the following errors:

sharpsl-pm sharpsl-pm: Error: AC check failed: voltage -22.
sharpsl-pm sharpsl-pm: Charging Error!
sharpsl-pm sharpsl-pm: Warning: Cannot read main battery!

Looking at the recent changes, I found that commit 31455bbd ("spi:
pxa2xx_spi: Convert to use GPIO descriptors") replaced the deprecated
SPI chip select platform device code with a gpiod lookup table. However,
this didn't seem to work until I changed the `dev_id` member from the
device name to the bus id. I'm not entirely sure why this is necessary,
but I suspect it is related to the fact that in sysfs SPI devices are
attached under /sys/devices/.../dev_name/spi_master/spiB/spiB.C, rather
than directly to the device."

After reviewing the change I conclude that the same fix is needed
for all affected boards.

Fixes: 31455bbd ("spi: pxa2xx_spi: Convert to use GPIO descriptors")
Reported-by: NLaurence de Bruxelles <lfdebrux@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220722114611.1517414-1-linus.walleij@linaro.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'at91-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes

AT91 fixes for 5.19 #3

It contains one fix for LAN966 based SoCs fixing the frequency of
sys_clk. sys_clk is feeding different IPs so having proper frequency
for it in DT is necessary for proper working of different drivers.

* tag 'at91-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: dts: lan966x: fix sys_clk frequency

Link: https://lore.kernel.org/r/20220721075705.1739915-1-claudiu.beznea@microchip.comSigned-off-by: NArnd Bergmann <arnd@arndb.de>

I recently switched to my Alibaba email address. So add aliases for my
previous email addresses.
Signed-off-by: NBaolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The sys_clk frequency is 165.625MHz. The register reference of the
Generic Clock controller lists the CPU clock as 600MHz, the DDR clock as
300MHz and the SYS clock as 162.5MHz. This is wrong. It was first
noticed during the fan driver development and it was measured and
verified via the CLK_MON output of the SoC which can be configured to
output sys_clk/64.

The core PLL settings (which drives the SYS clock) seems to be as
follows:
  DIVF = 52
  DIVQ = 3
  DIVR = 1

With a refernce clock of 25MHz, this means we have a post divider clock
  Fpfd = Fref / (DIVR + 1) = 25MHz / (1 + 1) = 12.5MHz

The resulting VCO frequency is then
  Fvco = Fpfd * (DIVF + 1) * 2 = 12.5MHz * (52 + 1) * 2 = 1325MHz

And the output frequency is
  Fout = Fvco / 2^DIVQ = 1325MHz / 2^3 = 165.625Mhz

This all adds up to the constrains of the PLL:
    10MHz <= Fpfd <= 200MHz
    20MHz <= Fout <= 1000MHz
  1000MHz <= Fvco <= 2000MHz

Fixes: 290deaa1 ("ARM: dts: add DT for lan966 SoC and 2-port board pcb8291")
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NKavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220326194028.2945985-1-michael@walle.cc

Pull intel drm build fix from Rodrigo Vivi:
 "Our 'dim' flow has a problem with fixes of fixes getting missed. We
  need to take a look on that later.

  Meanwhile, please allow me to quickly propagate this fix for the
  32-bit build issue here upstream"

* tag 'drm-intel-fixes-2022-07-17' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915/ttm: fix 32b build

Merge tag 'perf-tools-fixes-for-v5.19-2022-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix SIGSEGV when processing syscall args in perf.data files in 'perf
   trace'

 - Sync kvm, msr-index and cpufeatures headers with the kernel sources

 - Fix 'convert perf time to TSC' 'perf test':
     - No need to open events twice
     - Fix finding correct event on hybrid systems

* tag 'perf-tools-fixes-for-v5.19-2022-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf trace: Fix SIGSEGV when processing syscall args
  perf tests: Fix Convert perf time to TSC test for hybrid
  perf tests: Stop Convert perf time to TSC test opening events twice
  tools arch x86: Sync the msr-index.h copy with the kernel sources
  tools headers cpufeatures: Sync with the kernel sources
  tools headers UAPI: Sync linux/kvm.h with the kernel sources

Since segment_pages is no longer a compile time constant, it looks the
DIV_ROUND_UP(node->size, segment_pages) breaks the 32b build. Simplest
is just to use the ULL variant, but really we should need not need more
than u32 for the page alignment (also we are limited by that due to the
sg->length type), so also make it all u32.
Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Fixes: aff1e0b0 ("drm/i915/ttm: fix sg_table construction")
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Cc: Nirmoy Das <nirmoy.das@linux.intel.com>
Reviewed-by: NNirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220712174050.592550-1-matthew.auld@intel.com
(cherry picked from commit 9306b2b2)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Pull perf fix from Borislav Petkov:

 - A single data race fix on the perf event cleanup path to avoid
   endless loops due to insufficient locking

* tag 'perf_urgent_for_v5.19_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix data race between perf_event_set_output() and perf_mmap_close()

Pull x86 fixes from Borislav Petkov:

 - Improve the check whether the kernel supports WP mappings so that it
   can accomodate a XenPV guest due to how the latter is setting up the
   PAT machinery

  - Now that the retbleed nightmare is public, here's the first round of
    fallout fixes:

      * Fix a build failure on 32-bit due to missing include

      * Remove an untraining point in espfix64 return path

      * other small cleanups

* tag 'x86_urgent_for_v5.19_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bugs: Remove apostrophe typo
  um: Add missing apply_returns()
  x86/entry: Remove UNTRAIN_RET from native_irq_return_ldt
  x86/bugs: Mark retbleed_strings static
  x86/pat: Fix x86_has_pat_wp()
  x86/asm/32: Fix ANNOTATE_UNRET_SAFE use on 32-bit

Pull gpio fix from Bartosz Golaszewski:

 - fix a configfs attribute of the gpio-sim module

* tag 'gpio-fixes-for-v5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: sim: fix the chip_name configfs item

Pull input fixes from Dmitry Torokhov:

 - fix Goodix driver to properly behave on the Aya Neo Next

 - some more sanity checks in usbtouchscreen driver

 - a tweak in wm97xx driver in preparation for remove() to return void

 - a clarification in input core regarding units of measurement for
   resolution on touch events.

* tag 'input-for-v5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: document the units for resolution of size axes
  Input: goodix - call acpi_device_fix_up_power() in some cases
  Input: wm97xx - make .remove() obviously always return 0
  Input: usbtouchscreen - add driver_info sanity check

Pull power supply fixes from Sebastian Reichel:

 - power-supply core temperature interpolation regression fix for
   incorrect boundaries

 - ab8500 needs to destroy its work queues in error paths

 - Fix old DT refcount leak in arm-versatile

* tag 'for-v5.19-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power: supply: core: Fix boundary conditions in interpolation
  power/reset: arm-versatile: Fix refcount leak in versatile_reboot_probe
  power: supply: ab8500_fg: add missing destroy_workqueue in ab8500_fg_probe

On powerpc, 'perf trace' is crashing with a SIGSEGV when trying to
process a perf.data file created with 'perf trace record -p':

  #0  0x00000001225b8988 in syscall_arg__scnprintf_augmented_string <snip> at builtin-trace.c:1492
  #1  syscall_arg__scnprintf_filename <snip> at builtin-trace.c:1492
  #2  syscall_arg__scnprintf_filename <snip> at builtin-trace.c:1486
  #3  0x00000001225bdd9c in syscall_arg_fmt__scnprintf_val <snip> at builtin-trace.c:1973
  #4  syscall__scnprintf_args <snip> at builtin-trace.c:2041
  #5  0x00000001225bff04 in trace__sys_enter <snip> at builtin-trace.c:2319

That points to the below code in tools/perf/builtin-trace.c:
	/*
	 * If this is raw_syscalls.sys_enter, then it always comes with the 6 possible
	 * arguments, even if the syscall being handled, say "openat", uses only 4 arguments
	 * this breaks syscall__augmented_args() check for augmented args, as we calculate
	 * syscall->args_size using each syscalls:sys_enter_NAME tracefs format file,
	 * so when handling, say the openat syscall, we end up getting 6 args for the
	 * raw_syscalls:sys_enter event, when we expected just 4, we end up mistakenly
	 * thinking that the extra 2 u64 args are the augmented filename, so just check
	 * here and avoid using augmented syscalls when the evsel is the raw_syscalls one.
	 */
	if (evsel != trace->syscalls.events.sys_enter)
		augmented_args = syscall__augmented_args(sc, sample, &augmented_args_size, trace->raw_augmented_syscalls_args_size);

As the comment points out, we should not be trying to augment the args
for raw_syscalls. However, when processing a perf.data file, we are not
initializing those properly. Fix the same.
Reported-by: NClaudio Carvalho <cclaudio@linux.ibm.com>
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/20220707090900.572584-1-naveen.n.rao@linux.vnet.ibm.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

The test does not always correctly determine the number of events for
hybrids, nor allow for more than 1 evsel when parsing.

Fix by iterating the events actually created and getting the correct
evsel for the events processed.

Fixes: d9da6f70 ("perf tests: Support 'Convert perf time to TSC' test for hybrid")
Reviewed-by: NKan Liang <kan.liang@linux.intel.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: https://lore.kernel.org/r/20220713123459.24145-3-adrian.hunter@intel.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

Do not call evlist__open() twice.

Fixes: 5bb017d4 ("perf test: Fix error message for test case 71 on s390, where it is not supported")
Reviewed-by: NKan Liang <kan.liang@linux.intel.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: https://lore.kernel.org/r/20220713123459.24145-2-adrian.hunter@intel.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

To pick up the changes from these csets:

  4ad3278d ("x86/speculation: Disable RRSBA behavior")
  d7caac99 ("x86/cpu/amd: Add Spectral Chicken")

That cause no changes to tooling:

  $ tools/perf/trace/beauty/tracepoints/x86_msr.sh > before
  $ cp arch/x86/include/asm/msr-index.h tools/arch/x86/include/asm/msr-index.h
  $ tools/perf/trace/beauty/tracepoints/x86_msr.sh > after
  $ diff -u before after
  $

Just silences this perf build warning:

  Warning: Kernel ABI header at 'tools/arch/x86/include/asm/msr-index.h' differs from latest version at 'arch/x86/include/asm/msr-index.h'
  diff -u tools/arch/x86/include/asm/msr-index.h arch/x86/include/asm/msr-index.h

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/lkml/YtQTm9wsB3hxQWvy@kernel.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

To pick the changes from:

  f43b9876 ("x86/retbleed: Add fine grained Kconfig knobs")
  a149180f ("x86: Add magic AMD return-thunk")
  15e67227 ("x86: Undo return-thunk damage")
  369ae6ff ("x86/retpoline: Cleanup some #ifdefery")
  4ad3278d x86/speculation: Disable RRSBA behavior
  26aae8cc x86/cpu/amd: Enumerate BTC_NO
  9756bba2 x86/speculation: Fill RSB on vmexit for IBRS
  3ebc1700 x86/bugs: Add retbleed=ibpb
  2dbb887e x86/entry: Add kernel IBRS implementation
  6b80b59b x86/bugs: Report AMD retbleed vulnerability
  a149180f x86: Add magic AMD return-thunk
  15e67227 x86: Undo return-thunk damage
  a883d624 x86/cpufeatures: Move RETPOLINE flags to word 11
  51802186 x86/speculation/mmio: Enumerate Processor MMIO Stale Data bug

This only causes these perf files to be rebuilt:

  CC       /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o
  CC       /tmp/build/perf/bench/mem-memset-x86-64-asm.o

And addresses this perf build warning:

  Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
  diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h
  Warning: Kernel ABI header at 'tools/arch/x86/include/asm/disabled-features.h' differs from latest version at 'arch/x86/include/asm/disabled-features.h'
  diff -u tools/arch/x86/include/asm/disabled-features.h arch/x86/include/asm/disabled-features.h

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org
Link: https://lore.kernel.org/lkml/YtQM40VmiLTkPND2@kernel.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

To pick the changes in:

  1b870fa5 ("kvm: stats: tell userspace which values are boolean")

That just rebuilds perf, as these patches don't add any new KVM ioctl to
be harvested for the the 'perf trace' ioctl syscall argument
beautifiers.

This is also by now used by tools/testing/selftests/kvm/, a simple test
build succeeded.

This silences this perf build warning:

  Warning: Kernel ABI header at 'tools/include/uapi/linux/kvm.h' differs from latest version at 'include/uapi/linux/kvm.h'
  diff -u tools/include/uapi/linux/kvm.h include/uapi/linux/kvm.h

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: http://lore.kernel.org/lkml/YtQLDvQrBhJNl3n5@kernel.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

Pull btrfs reverts from David Sterba:
 "Due to a recent report [1] we need to revert the radix tree to xarray
  conversion patches.

  There's a problem with sleeping under spinlock, when xa_insert could
  allocate memory under pressure. We use GFP_NOFS so this is a real
  problem that we unfortunately did not discover during review.

  I'm sorry to do such change at rc6 time but the revert is IMO the
  safer option, there are patches to use mutex instead of the spin locks
  but that would need more testing. The revert branch has been tested on
  a few setups, all seem ok.

  The conversion to xarray will be revisited in the future"

Link: https://lore.kernel.org/linux-btrfs/cover.1657097693.git.fdmanana@suse.com/ [1]

* tag 'for-5.19-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: turn delayed_nodes_tree into an XArray"
  Revert "btrfs: turn name_cache radix tree into XArray in send_ctx"
  Revert "btrfs: turn fs_info member buffer_radix into XArray"
  Revert "btrfs: turn fs_roots_radix in btrfs_fs_info into an XArray"

Pull SCSI fixes from James Bottomley:
 "Six small and reasonably obvious fixes, all in drivers"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: pm80xx: Set stopped phy's linkrate to Disabled
  scsi: pm80xx: Fix 'Unknown' max/min linkrate
  scsi: ufs: core: Fix missing clk change notification on host reset
  scsi: ufs: core: Drop loglevel of WriteBoost message
  scsi: megaraid: Clear READ queue map's nr_queues
  scsi: target: Fix WRITE_SAME No Data Buffer crash

Pull block fixes from Jens Axboe:
 "Two NVMe fixes, and a regression fix for the core block layer from
  this merge window"

* tag 'block-5.19-2022-07-15' of git://git.kernel.dk/linux-block:
  block: fix missing blkcg_bio_issue_init
  nvme: fix block device naming collision
  nvme-pci: fix freeze accounting for error handling

Pull USB driver fixes from Greg KH:
 "Here are some small USB driver fixes and new device ids for 5.19-rc7.
  They include:

   - new usb-serial driver ids

   - typec uevent fix

   - uvc gadget driver fix

   - dwc3 driver fixes

   - ehci-fsl driver fix

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: ftdi_sio: add Belimo device ids
  drivers/usb/host/ehci-fsl: Fix interrupt setup in host mode.
  usb: gadget: uvc: fix changing interface name via configfs
  usb: typec: add missing uevent when partner support PD
  usb: dwc3-am62: remove unnecesary clk_put()
  usb: dwc3: gadget: Fix event pending check

Pull tty and serial driver fixes from Greg KH:
 "Here are some TTY and Serial driver fixes for 5.19-rc7. They resolve a
  number of reported problems including:

   - longtime bug in pty_write() that has been reported in the past.

   - 8250 driver fixes

   - new serial device ids

   - vt overlapping data copy bugfix

   - other tiny serial driver bugfixes

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: use new tty_insert_flip_string_and_push_buffer() in pty_write()
  tty: extract tty_flip_buffer_commit() from tty_flip_buffer_push()
  serial: 8250: dw: Fix the macro RZN1_UART_xDMACR_8_WORD_BURST
  vt: fix memory overlapping when deleting chars in the buffer
  serial: mvebu-uart: correctly report configured baudrate value
  serial: 8250: Fix PM usage_count for console handover
  serial: 8250: fix return error code in serial8250_request_std_resource()
  serial: stm32: Clear prev values before setting RTS delays
  tty: Add N_CAN327 line discipline ID for ELM327 based CAN driver
  serial: 8250: Fix __stop_tx() & DMA Tx restart races
  serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle
  tty: serial: samsung_tty: set dma burst_size to 1
  serial: 8250: dw: enable using pdata with ACPI

Pull s390 fixes from Alexander Gordeev:

 - Fix building of out-of-tree kernel modules without a pre-built kernel
   in case CONFIG_EXPOLINE_EXTERN=y.

 - Fix a reference counting error that could prevent unloading of zcrypt
   modules.

* tag 's390-5.19-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/ap: fix error handling in __verify_queue_reservations()
  s390/nospec: remove unneeded header includes
  s390/nospec: build expoline.o for modules_prepare target

Pull power management fix from Rafael Wysocki
 "Fix recent regression in the cpufreq mediatek driver related to
  incorrect handling of regulator_get_optional() return value
  (AngeloGioacchino Del Regno)"

* tag 'pm-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: mediatek: Handle sram regulator probe deferral

Pull ACPI fix from Rafael Wysocki:
 "Fix more fallout from recent changes of the ACPI CPPC handling on AMD
  platforms (Mario Limonciello)"

* tag 'acpi-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: CPPC: Fix enabling CPPC on AMD systems with shared memory

Pull printk fix from Petr Mladek:

 - Make pr_flush() fast when consoles are suspended.

* tag 'printk-for-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
  printk: do not wait for consoles when suspended

Currently the jitter mechanism will require two timer ticks per
iteration, and it requires N iterations per bit. This N is determined
with a small measurement, and if it's too big, it won't waste time with
jitter entropy because it'd take too long or not have sufficient entropy
anyway.

With the current max N of 32, there are large timeouts on systems with a
small CONFIG_HZ. Rather than set that maximum to 32, instead choose a
factor of CONFIG_HZ. In this case, 1/30 seems to yield sane values for
different configurations of CONFIG_HZ.
Reported-by: NVladimir Murzin <vladimir.murzin@arm.com>
Fixes: 78c768e6 ("random: vary jitter iterations based on cycle counter speed")
Signed-off-by: NJason A. Donenfeld <Jason@zx2c4.com>
Tested-by: NVladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When running with return thunks enabled under 32-bit EFI, the system
crashes with:

  kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
  BUG: unable to handle page fault for address: 000000005bc02900
  #PF: supervisor instruction fetch in kernel mode
  #PF: error_code(0x0011) - permissions violation
  PGD 18f7063 P4D 18f7063 PUD 18ff063 PMD 190e063 PTE 800000005bc02063
  Oops: 0011 [#1] PREEMPT SMP PTI
  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.19.0-rc6+ #166
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
  RIP: 0010:0x5bc02900
  Code: Unable to access opcode bytes at RIP 0x5bc028d6.
  RSP: 0018:ffffffffb3203e10 EFLAGS: 00010046
  RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000048
  RDX: 000000000190dfac RSI: 0000000000001710 RDI: 000000007eae823b
  RBP: ffffffffb3203e70 R08: 0000000001970000 R09: ffffffffb3203e28
  R10: 747563657865206c R11: 6c6977203a696665 R12: 0000000000001710
  R13: 0000000000000030 R14: 0000000001970000 R15: 0000000000000001
  FS:  0000000000000000(0000) GS:ffff8e013ca00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0018 ES: 0018 CR0: 0000000080050033
  CR2: 000000005bc02900 CR3: 0000000001930000 CR4: 00000000000006f0
  Call Trace:
   ? efi_set_virtual_address_map+0x9c/0x175
   efi_enter_virtual_mode+0x4a6/0x53e
   start_kernel+0x67c/0x71e
   x86_64_start_reservations+0x24/0x2a
   x86_64_start_kernel+0xe9/0xf4
   secondary_startup_64_no_verify+0xe5/0xeb

That's because it cannot jump to the return thunk from the 32-bit code.

Using a naked RET and marking it as safe allows the system to proceed
booting.

Fixes: aa3d4803 ("x86: Use return-thunk in asm code")
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@canonical.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: <stable@vger.kernel.org>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove a superfluous ' in the mitigation string.

Fixes: e8ec1b6e ("x86/bugs: Enable STIBP for JMP2RET")
Signed-off-by: NKim Phillips <kim.phillips@amd.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>

Pull RISC-V fixes from Palmer Dabbelt:

 - A fix to avoid printing a warning when modules do not exercise any
   errata-dependent behavior and the SiFive errata are enabled.

 - A fix to the Microchip PFSOC to attach the L2 cache to the CPU nodes.

* tag 'riscv-for-linus-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: don't warn for sifive erratas in modules
  riscv: dts: microchip: hook up the mpfs' l2cache

Pull KVM fixes from Paolo Bonzini:
 "RISC-V:
   - Fix missing PAGE_PFN_MASK

   - Fix SRCU deadlock caused by kvm_riscv_check_vcpu_requests()

  x86:
   - Fix for nested virtualization when TSC scaling is active

   - Estimate the size of fastcc subroutines conservatively, avoiding
     disastrous underestimation when return thunks are enabled

   - Avoid possible use of uninitialized fields of 'struct
     kvm_lapic_irq'

  Generic:
   - Mark as such the boolean values available from the statistics file
     descriptors

   - Clarify statistics documentation"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: emulate: do not adjust size of fastop and setcc subroutines
  KVM: x86: Fully initialize 'struct kvm_lapic_irq' in kvm_pv_kick_cpu_op()
  Documentation: kvm: clarify histogram units
  kvm: stats: tell userspace which values are boolean
  x86/kvm: fix FASTOP_SIZE when return thunks are enabled
  KVM: nVMX: Always enable TSC scaling for L2 when it was enabled for L1
  RISC-V: KVM: Fix SRCU deadlock caused by kvm_riscv_check_vcpu_requests()
  riscv: Fix missing PAGE_PFN_MASK

Pull ceph fix from Ilya Dryomov:
 "A folio locking fixup that Xiubo and David cooperated on, marked for
  stable. Most of it is in netfs but I picked it up into ceph tree on
  agreement with David"

* tag 'ceph-for-5.19-rc7' of https://github.com/ceph/ceph-client:
  netfs: do not unlock and put the folio twice

Pull spi fixes from Mark Brown:
 "A few driver specific fixes, none especially remarkable, plus a
  MAINTAINERS file update due to the previous maintainer for the NXP
  FSPI driver having left the company"

* tag 'spi-fix-v5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: cadence-quadspi: Remove spi_master_put() in probe failure path
  MAINTAINERS: change the NXP FSPI driver maintainer.
  spi: amd: Limit max transfer and message size
  spi: aspeed: Fix division by zero
  spi: aspeed: Add dev_dbg() to dump the spi-mem direct mapping descriptor

Pull ARM SoC fixes from Arnd Bergmann:
 "Most of the contents are bugfixes for the devicetree files:

   - A Qualcomm MSM8974 pin controller regression, caused by a cleanup
     patch that gets partially reverted here.

   - Missing properties for Broadcom BCM49xx to fix timer detection and
     SMP boot.

   - Fix touchscreen pinctrl for imx6ull-colibri board

   - Multiple fixes for Rockchip rk3399 based machines including the vdu
     clock-rate fix, otg port fix on Quartz64-A and ethernet on
     Quartz64-B

   - Fixes for misspelled DT contents causing minor problems on
     imx6qdl-ts7970m, orangepi-zero, sama5d2, kontron-kswitch-d10, and
     ls1028a

  And a couple of changes elsewhere:

   - Fix binding for Allwinner D1 display pipeline

   - Trivial code fixes to the TEE and reset controller driver
     subsystems and the rockchip platform code.

   - Multiple updates to the MAINTAINERS files, marking the Palm Treo
     support as orphaned, and fixing some entries for added or changed
     file names"

* tag 'soc-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
  arm64: dts: broadcom: bcm4908: Fix cpu node for smp boot
  arm64: dts: broadcom: bcm4908: Fix timer node for BCM4906 SoC
  ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
  ARM: dts: at91: sama5d2: Fix typo in i2s1 node
  tee: tee_get_drvdata(): fix description of return value
  optee: Remove duplicate 'of' in two places.
  ARM: dts: kswitch-d10: use open drain mode for coma-mode pins
  ARM: dts: colibri-imx6ull: fix snvs pinmux group
  optee: smc_abi.c: fix wrong pointer passed to IS_ERR/PTR_ERR()
  MAINTAINERS: add polarfire rng, pci and clock drivers
  MAINTAINERS: mark ARM/PALM TREO SUPPORT orphan
  ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
  arm64: dts: ls1028a: Update SFP node to include clock
  dt-bindings: display: sun4i: Fix D1 pipeline count
  ARM: dts: qcom: msm8974: re-add missing pinctrl
  reset: Fix devm bulk optional exclusive control getter
  MAINTAINERS: rectify entry for SYNOPSYS AXS10x RESET CONTROLLER DRIVER
  ARM: rockchip: Add missing of_node_put() in rockchip_suspend_init()
  arm64: dts: rockchip: Assign RK3399 VDU clock rate
  arm64: dts: rockchip: Fix Quartz64-A dwc3 otg port behavior
  ...

This reverts commit 253bf575.

Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.

Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.

[1] https://lore.kernel.org/linux-btrfs/cover.1657097693.git.fdmanana@suse.com/Reported-by: NFilipe Manana <fdmanana@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

This reverts commit 40769420.

Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.

Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.

[1] https://lore.kernel.org/linux-btrfs/cover.1657097693.git.fdmanana@suse.com/Reported-by: NFilipe Manana <fdmanana@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

This reverts commit 8ee92268.

Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.

Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.

[1] https://lore.kernel.org/linux-btrfs/cover.1657097693.git.fdmanana@suse.com/Reported-by: NFilipe Manana <fdmanana@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

This reverts commit 48b36a60.

Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.

Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.

[1] https://lore.kernel.org/linux-btrfs/cover.1657097693.git.fdmanana@suse.com/Reported-by: NFilipe Manana <fdmanana@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>