Initialization of pointer should be done with NULL. Removes sparse
warnings:
arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds context save/restore for mcr register as state of mcr register
is lost after core off.
Signed-off-by: NGovindraj R <govindraj.raja@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add initial support for the OMAP4 based Panda Board.
Signed-off-by: NDavid Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver
Signed-off-by: NHemanth V <hemanthv@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.

This patch fixes the same and has VAUX1 as supply to MMC2 card.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This commit will enable usage of tsl2563 ambient light sensor on Nokia N900.
Signed-off-by: NAmeya Palande <ameya.palande@nokia.com>
Signed-off-by: NMathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With these and upcoming change to tpa6130a2 driver it's possible to add
support for the TPA6130A2 headphone amplifier.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There is REGULATOR_SUPPLY macro available for initializing the struct
regulator_consumer_supply so use it where applicable (all other supplies
than vdds_sdi) as it improves the readability.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NEduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Proper operation of the tlv320aic3x audio codec requires that reset
sequencing is done in pair with supply voltages when using the regulator
framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x
data.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.

Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.

Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.

Prepare for these by defining the V28 as always_on regulator.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform data for NAND and wifi, also setup all GPIOs
needed to use the wifi chip.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update gpio-keys setup so it matches what is on default firmware.
Also make use of debounce feature in gpio-keys instead of setting it
explicitly, as gpio-keys is now capable of using hardware debounce on
OMAPs thanks to recent gpiolib changes.
Also fix a sparce warning along the way.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM3.
Signed-off-by: NOhad Ben-Cohen <ohadb@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM2.
Signed-off-by: NOhad Ben-Cohen <ohadb@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Devkit8000 uses the TPS65930 and not the TWL4030.
The TPS65930 uses only a subset of the power supplies
of the TWL4030.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap_board_config is no longer used and thats why empty.
This patch removes the empty omap_board_config.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Using the macro gpio_is_valid for check of valid gpio pins.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Replacing supplies with the REGULATOR_SUPPLY macro.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.

vaux2 is not used on Devkit8000.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The VDVI power supply is no longer needed in
board code with the new DSS2 interface.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch corrects the LCD reset pin configuration.

Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.
Signed-off-by: NKan-Ru Chen <kanru@0xlab.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch corrects the DVI-D output setup of Devkit8000

Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.
Signed-off-by: NKan-Ru Chen <kanru@0xlab.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Choose the generic panel for lcd code of Devkit8000.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Corrected the wrong power supplies in devkit8000 code.

Add supply for ads7846 to support the new regulator framework for
touchscreen.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

MACH_OMAP2_H4_USB1 doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

MACH_OMAP_H4_OTG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

APM doesn't exist in Kconfig, therefore removing all references for it
from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

LEDS_OMAP_DEBUG doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_DEBUG_LEDS from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP_STI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP_DSP doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated to apply on top of already queued patches]
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP_IR doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated for new mux code]
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP_MUX_ERRORS doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_MUX_WARNINGS in the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Acked-by: NKirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This produces a sane config that's suitable for using as the
base for most omap2/3/4 boards.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Select all omaps and boards by default
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move omap2/3/4 specific Kconfig options to mach-omap2/Kconfig
Signed-off-by: NTony Lindgren <tony@atomide.com>

This will make Kconfig look nicer for selecting omap processor type
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use 32KiHZ timer by default as this is available on all omaps
except 15xx based systems.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise we have to disable it manually to avoid compile errors.

Now it's only enabled only for the selected machines as suggested
by Anton Vorontsov <cbouatmailru@gmail.com>:

$ git grep VGA_CONSOLE= arch/arm/configs/
arch/arm/configs/footbridge_defconfig:CONFIG_VGA_CONSOLE=y
arch/arm/configs/integrator_defconfig:CONFIG_VGA_CONSOLE=y
arch/arm/configs/netwinder_defconfig:CONFIG_VGA_CONSOLE=y

Note that the Kconfig entry no longer needs separate entries
for ARCH_ACORN, ARCH_EBSA110 ARCH_VERSATILE.

Cc: linux-fbdev@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>