As the probe sequence is not guaranteed contrary to the assumption
of the commit 2d8e276a9030, same has to be reverted.

commit 2d8e276a9030 ("net: netcp: remove dead code from the driver")
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy used for K2G allows for internal delays to be added optionally
to the clock circuitry based on board desing. To add this support,
enhance the driver to use of_get_phy_mode() to read the phy-mode from
the phy device and pass the same to phy through of_phy_connect().
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The stats block in 2u cpsw hardware is similar to the one on nu
and hence handle it in a similar way by using a macro that includes
2u hardware as well.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently support only vlan priority zero. So map the
vlan priorities to zero flow in hardware.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce rgmii link status to handle link state events for 2u
cpsw hardware on K2G.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

2u cpsw hardware on K2G uses rgmii link to interface with Phy. So add
support for this interface in the code so that driver can be re-used
for 2u hardware.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a preparatory patch to add support for 2u cpsw hardware found on
K2G SoC, make sgmii configuration conditional. This is required
since 2u uses RGMII interface instead of SGMII and to allow for driver
re-use.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver currently uses macro for NU and XBE hardwrae, while other
places for older hardware such as that on K2H/K SoC (version 1.4
of the cpsw hardware, it explicitly check for the ss_version
inline. Add a new macro for version 1.4 and use it to customize
code in the driver. While at it also fix similar issue with
checking XBE version by re-using existing macro IS_SS_ID_XGBE().
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert all code paths referencing a FIB entry from
rt6_info to fib6_info.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce fib6_nh structure and move nexthop related data from
rt6_info and rt6_info.dst to fib6_nh. References to dev, gateway or
lwtstate from a FIB lookup perspective are converted to use fib6_nh;
datapath references to dst version are left as is.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to display pause settings
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing API ndo_xdp_xmit to take a struct xdp_frame instead of struct
xdp_buff.  This brings xdp_return_frame and ndp_xdp_xmit in sync.

This builds towards changing the API further to become a bulk API,
because xdp_buff is not a queue-able object while xdp_frame is.

V4: Adjust for commit 59655a5b ("tuntap: XDP_TX can use native XDP")
V7: Adjust for commit d9314c47 ("i40e: add support for XDP_REDIRECT")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing API xdp_return_frame() to take struct xdp_frame as argument,
seems like a natural choice. But there are some subtle performance
details here that needs extra care, which is a deliberate choice.

When de-referencing xdp_frame on a remote CPU during DMA-TX
completion, result in the cache-line is change to "Shared"
state. Later when the page is reused for RX, then this xdp_frame
cache-line is written, which change the state to "Modified".

This situation already happens (naturally) for, virtio_net, tun and
cpumap as the xdp_frame pointer is the queued object.  In tun and
cpumap, the ptr_ring is used for efficiently transferring cache-lines
(with pointers) between CPUs. Thus, the only option is to
de-referencing xdp_frame.

It is only the ixgbe driver that had an optimization, in which it can
avoid doing the de-reference of xdp_frame.  The driver already have
TX-ring queue, which (in case of remote DMA-TX completion) have to be
transferred between CPUs anyhow.  In this data area, we stored a
struct xdp_mem_info and a data pointer, which allowed us to avoid
de-referencing xdp_frame.

To compensate for this, a prefetchw is used for telling the cache
coherency protocol about our access pattern.  My benchmarks show that
this prefetchw is enough to compensate the ixgbe driver.

V7: Adjust for commit d9314c47 ("i40e: add support for XDP_REDIRECT")
V8: Adjust for commit bd658dda ("net/mlx5e: Separate dma base address
and offset in dma_sync call")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch shows how it is possible to have both the driver local page
cache, which uses elevated refcnt for "catching"/avoiding SKB
put_page returns the page through the page allocator.  And at the
same time, have pages getting returned to the page_pool from
ndp_xdp_xmit DMA completion.

The performance improvement for XDP_REDIRECT in this patch is really
good.  Especially considering that (currently) the xdp_return_frame
API and page_pool_put_page() does per frame operations of both
rhashtable ID-lookup and locked return into (page_pool) ptr_ring.
(It is the plan to remove these per frame operation in a followup
patchset).

The benchmark performed was RX on mlx5 and XDP_REDIRECT out ixgbe,
with xdp_redirect_map (using devmap) . And the target/maximum
capability of ixgbe is 13Mpps (on this HW setup).

Before this patch for mlx5, XDP redirected frames were returned via
the page allocator.  The single flow performance was 6Mpps, and if I
started two flows the collective performance drop to 4Mpps, because we
hit the page allocator lock (further negative scaling occurs).

Two test scenarios need to be covered, for xdp_return_frame API, which
is DMA-TX completion running on same-CPU or cross-CPU free/return.
Results were same-CPU=10Mpps, and cross-CPU=12Mpps.  This is very
close to our 13Mpps max target.

The reason max target isn't reached in cross-CPU test, is likely due
to RX-ring DMA unmap/map overhead (which doesn't occur in ixgbe to
ixgbe testing).  It is also planned to remove this unnecessary DMA
unmap in a later patchset

V2: Adjustments requested by Tariq
 - Changed page_pool_create return codes not return NULL, only
   ERR_PTR, as this simplifies err handling in drivers.
 - Save a branch in mlx5e_page_release
 - Correct page_pool size calc for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ

V5: Updated patch desc

V8: Adjust for b0cedc84 ("net/mlx5e: Remove rq_headroom field from params")
V9:
 - Adjust for 121e8927 ("net/mlx5e: Refactor RQ XDP_TX indication")
 - Adjust for 73281b78 ("net/mlx5e: Derive Striding RQ size from MTU")
 - Correct handling if page_pool_create fail for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ

V10: Req from Tariq
 - Change pool_size calc for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need a fast page recycle mechanism for ndo_xdp_xmit API for returning
pages on DMA-TX completion time, which have good cross CPU
performance, given DMA-TX completion time can happen on a remote CPU.

Refurbish my page_pool code, that was presented[1] at MM-summit 2016.
Adapted page_pool code to not depend the page allocator and
integration into struct page.  The DMA mapping feature is kept,
even-though it will not be activated/used in this patchset.

[1] http://people.netfilter.org/hawk/presentations/MM-summit2016/generic_page_pool_mm_summit2016.pdf

V2: Adjustments requested by Tariq
 - Changed page_pool_create return codes, don't return NULL, only
   ERR_PTR, as this simplifies err handling in drivers.

V4: many small improvements and cleanups
- Add DOC comment section, that can be used by kernel-doc
- Improve fallback mode, to work better with refcnt based recycling
  e.g. remove a WARN as pointed out by Tariq
  e.g. quicker fallback if ptr_ring is empty.

V5: Fixed SPDX license as pointed out by Alexei

V6: Adjustments requested by Eric Dumazet
 - Adjust ____cacheline_aligned_in_smp usage/placement
 - Move rcu_head in struct page_pool
 - Free pages quicker on destroy, minimize resources delayed an RCU period
 - Remove code for forward/backward compat ABI interface

V8: Issues found by kbuild test robot
 - Address sparse should be static warnings
 - Only compile+link when a driver use/select page_pool,
   mlx5 selects CONFIG_PAGE_POOL, although its first used in two patches
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the IDA infrastructure for getting a cyclic increasing ID number,
that is used for keeping track of each registered allocator per
RX-queue xdp_rxq_info.  Instead of using the IDR infrastructure, which
uses a radix tree, use a dynamic rhashtable, for creating ID to
pointer lookup table, because this is faster.

The problem that is being solved here is that, the xdp_rxq_info
pointer (stored in xdp_buff) cannot be used directly, as the
guaranteed lifetime is too short.  The info is needed on a
(potentially) remote CPU during DMA-TX completion time . In an
xdp_frame the xdp_mem_info is stored, when it got converted from an
xdp_buff, which is sufficient for the simple page refcnt based recycle
schemes.

For more advanced allocators there is a need to store a pointer to the
registered allocator.  Thus, there is a need to guard the lifetime or
validity of the allocator pointer, which is done through this
rhashtable ID map to pointer. The removal and validity of of the
allocator and helper struct xdp_mem_allocator is guarded by RCU.  The
allocator will be created by the driver, and registered with
xdp_rxq_info_reg_mem_model().

It is up-to debate who is responsible for freeing the allocator
pointer or invoking the allocator destructor function.  In any case,
this must happen via RCU freeing.

Use the IDA infrastructure for getting a cyclic increasing ID number,
that is used for keeping track of each registered allocator per
RX-queue xdp_rxq_info.

V4: Per req of Jason Wang
- Use xdp_rxq_info_reg_mem_model() in all drivers implementing
  XDP_REDIRECT, even-though it's not strictly necessary when
  allocator==NULL for type MEM_TYPE_PAGE_SHARED (given it's zero).

V6: Per req of Alex Duyck
- Introduce rhashtable_lookup() call in later patch

V8: Address sparse should be static warnings (from kbuild test robot)
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now all the users of ndo_xdp_xmit have been converted to use xdp_return_frame.
This enable a different memory model, thus activating another code path
in the xdp_return_frame API.

V2: Fixed issues pointed out by Tariq.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also convert driver i40e, which very recently got XDP_REDIRECT support
in commit d9314c47 ("i40e: add support for XDP_REDIRECT").

V7: This patch got added in V7 of this patchset.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend struct ixgbe_tx_buffer to store the xdp_mem_info.

Notice that this could be optimized further by putting this into
a union in the struct ixgbe_tx_buffer, but this patchset
works towards removing this again.  Thus, this is not done.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This implements basic XDP redirect support in mlx5 driver.

Notice that the ndo_xdp_xmit() is NOT implemented, because that API
need some changes that this patchset is working towards.

The main purpose of this patch is have different drivers doing
XDP_REDIRECT to show how different memory models behave in a cross
driver world.

Update(pre-RFCv2 Tariq): Need to DMA unmap page before xdp_do_redirect,
as the return API does not exist yet to to keep this mapped.

Update(pre-RFCv3 Saeed): Don't mix XDP_TX and XDP_REDIRECT flushing,
introduce xdpsq.db.redirect_flush boolian.

V9: Adjust for commit 121e8927 ("net/mlx5e: Refactor RQ XDP_TX indication")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Added red_drops stats. Inbound packets dropped by RED, buffer exhaustion
2. Included fcs_err, jabber_err, l2_err and frame_err errors under
   rx_errors
3. Included fifo_err, dmac_drop, red_drops, fw_err_pko, fw_err_link and
   fw_err_drop under rx_dropped
4. Included max_collision_fail, max_deferral_fail, total_collisions,
   fw_err_pko, fw_err_link, fw_err_drop and fw_err_pki under tx_dropped
5. Counting dma mapping errors
6. Added some firmware stats description and removed for some
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Acked-by: NSatanand Burla <satananda.burla@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace magic number "0x5 << MAX_READ_REQUEST_SHIFT" with the
appropriate constant as defined in PCI core.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch stmmac_mode_ops to generic Hardware Interface Helpers instead of
using hard-coded callbacks. This makes the code more readable and more
flexible.

No functional change.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch stmmac_hwtimestamp to generic Hardware Interface Helpers instead
of using hard-coded callbacks. This makes the code more readable and
more flexible.

No functional change.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch stmmac_ops to generic Hardware Interface Helpers instead of using
hard-coded callbacks. This makes the code more readable and more
flexible.

No functional change.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch stmmac_dma_ops to generic Hardware Interface Helpers instead of
using hard-coded callbacks. This makes the code more readable and more
flexible.

No functional change.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch stmmac_desc_ops to generic Hardware Interface Helpers instead of
using hard-coded callbacks. This makes the code more readable and more
flexible.

No functional change.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the interface is down, head/tail of the descriptor
ring address is set to 0 in netsec_netdev_stop().
But netsec hardware still keeps the previous descriptor
ring address, so there is inconsistency between driver
and hardware after interface is up at a later time.
To address this inconsistency, add netsec_reset_hardware()
when the interface is down.

In addition, to minimize the reset process,
add flag to decide whether driver loads the netsec microcode.
Even if driver resets the netsec hardware, netsec microcode
keeps resident on RAM, so it is ok we only load the microcode
at initialization.

This patch is critical for installation over network.
Signed-off-by: NMasahisa KOJIMA <masahisa.kojima@linaro.org>
Fixes: 533dd11a ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: NJassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable TX-irq as well during ndo_open() as we can not count upon
RX to arrive early enough to trigger the napi. This patch is critical
for installation over network.

Fixes: 533dd11a ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: NJassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usage of of_device_get_match_data() reduce the code size a bit.

Also, the only way to call mtk_probe() is to match an entry in
of_mtk_match[], so match cannot be NULL.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.

If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi.  Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().

Fix it by checking for !bp->bnapi in bnxt_free_irq().

Fixes: e5811b8c ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings().  Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.

Fixes: fbcfc8e4 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:

	$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.

Fixes: f484f678 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch the following commands would succeed as far as the
user was concerned:

$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
	flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:01/44 action drop

The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed.  If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:

$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
	flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:02 action drop
...

There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not.  Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.

Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case netdev is closed at the moment of pci shutdown, aq_nic_stop
gets called second time. napi_disable in that case hangs indefinitely.
In other case, if device was never opened at all, we get oops because
of null pointer access.

We should invoke aq_nic_stop conditionally, only if device is running
at the moment of shutdown.
Reported-by: NDavid Arcari <darcari@redhat.com>
Fixes: 90869ddf ("net: aquantia: Implement pci shutdown callback")
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ASUS XG-C100C with 1.5.44 firmware a special mode called "dirty wake"
is active. With this mode when motherboard gets powered (but no poweron
happens yet), NIC automatically enables powersave link and watches
for WOL packet.
This normally allows to powerup the PC after AC power failures.

Not all motherboards or bios settings gives power to PCI slots,
so this mode is not enabled on all the hardware.

4.16 linux driver introduced full hardware reset sequence
This is required since before that we had no NIC hardware
reset implemented and there were side effects of "not clean start".

But this full reset is incompatible with "dirty wake" WOL feature
it keeps the PHY link in a special mode forever. As a consequence,
driver sees no link and no traffic.

To fix this we forcibly change FW state to idle state before doing
the full reset. This makes FW to restore link state.

Fixes: c8c82eb3 net: aquantia: Introduce global AQC hardware reset sequence
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is too expensive to pass u64 values via linked list, instead
allocate array for them by overall number of mac addresses from netdev.

This eventually removes multiple kmalloc() calls, aviod memory
fragmentation and allow to put single null check on kmalloc
return value in order to prevent a potential null pointer dereference.

Addresses-Coverity-ID: 1467429 ("Dereference null return value")
Fixes: 37c3347e ("net: thunderx: add ndo_set_rx_mode callback implementation for VF")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NVadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This resolves race during initialization where the resources with
ops are registered before driver and the structures used by occ_get
op is initialized. So keep occ_get callbacks registered only when
all structs are initialized.

The example flows, as it is in mlxsw:
1) driver load/asic probe:
   mlxsw_core
      -> mlxsw_sp_resources_register
        -> mlxsw_sp_kvdl_resources_register
          -> devlink_resource_register IDX
   mlxsw_spectrum
      -> mlxsw_sp_kvdl_init
        -> mlxsw_sp_kvdl_parts_init
          -> mlxsw_sp_kvdl_part_init
            -> devlink_resource_size_get IDX (to get the current setup
                                              size from devlink)
        -> devlink_resource_occ_get_register IDX (register current
                                                  occupancy getter)
2) reload triggered by devlink command:
  -> mlxsw_devlink_core_bus_device_reload
    -> mlxsw_sp_fini
      -> mlxsw_sp_kvdl_fini
	-> devlink_resource_occ_get_unregister IDX
    (struct mlxsw_sp *mlxsw_sp is freed at this point, call to occ get
     which is using mlxsw_sp would cause use-after free)
    -> mlxsw_sp_init
      -> mlxsw_sp_kvdl_init
        -> mlxsw_sp_kvdl_parts_init
          -> mlxsw_sp_kvdl_part_init
            -> devlink_resource_size_get IDX (to get the current setup
                                              size from devlink)
        -> devlink_resource_occ_get_register IDX (register current
                                                  occupancy getter)

Fixes: d9f9b9a4 ("devlink: Add support for resource abstraction")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>