This patch adds OF match table to the driver to allow instantiating it
using device tree.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

all other drivers using Synopsys IPs with DT
have a compatible of snps,$driver, in order
to add consistency, we are switching over to
snps,dwc3 but keeping synopsys,dwc3 in the core
driver to maintain backwards compatibility.

New DTS bindings should NOT use synopsys,dwc3.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this helper will be used for controllers which
want to work at a lower speed even though they
support higher USB transfer rates.

One such case is Texas Instruments' AM437x
SoC where it uses a USB3 controller without
a USB3 PHY, rendering the controller USB2-only.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The TWL6025 was never released beyond sample form and was replaced by
the PhoenixLite range of chips - TWL6032. Change the references to
reference the TWL6032 class and name the registers to twl6032 in line with
an actual released chip name to avoid confusion.

Currently there are no users of TWL6025 in the code.
Signed-off-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NOleksandr Kozaruk <oleksandr.kozaruk@ti.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Reviwed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Even if a chipidea core is otg capable the board may not be. This allows
to explicitly set the core to host/peripheral mode. Without these flags
the driver falls back to the old behaviour.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes it possible to configure the PTW, PTS and STS bits
inside the portsc register for host and device mode before the driver
starts and the phy can be addressed as hardware implementation is
designed.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Document device tree binding information as required by the
Samsung' USB 3.0 controller.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch will allow ux500-musb to be probed and configured solely from
configuration found in Device Tree.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-usb@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch is to add a property 'disabled-ports' representing the unused port
of USB3503. USB3503 can support up to 3 USB host port and each ports can be
controlled to be enabled or disabled. Do not describe this property if all
ports must be enabled.

You can represent the ports to disable in the device tree.

	usb3503@08{
		...
		disabled-ports = <2 3>;
		...
	};
Signed-off-by: NDongjin Kim <tobetter@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NAnatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Allow to compile the driver all the time if AT91 enabled.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NBo Shen <voice.shen@atmel.com>

The existing Tegra USB bindings have a few issues:

1) Many properties are documented as being part of the EHCI controller
node, yet they apply more to the PHY device. They should be moved.

2) Some registers in PHY1 are shared with PHY3, and hence PHY3 needs a
reg entry to point at PHY1's register space. We can't assume the PHY1
driver is present, so the PHY3 driver will directly access those
registers.

3) The list of clocks required by the PHY was missing some required
entries.

4) UTMI PHY Timing parameters are added

5) VBUS control is now specified using a regulator rather than a plain GPIO

6) Added nvidia,is-wired property to indicate whether the device is
hard wired on the board, or pluggable.

This patch fixes the binding definition to resolve these issues.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Fix spelling typos in Documentation/devicetree/bindings.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add usb otg data node in omap4/omap3 device tree file. Also update
the node with board specific setting in omapx-<board>.dts file.
The dt data specifies among others the interface type (ULPI or UTMI),
mode which is mostly OTG, power that specifies the amount of power
this can supply when in host mode.

The information about usb otg node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The exynox4210-ehci and exynos4210-ohci nodes need a clock specified
using the common clock framework.  Document it.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This adds a post handling routine which is called after
ci13xxx_add_device was called. The first user is the mx25, which has to
disable the external-vbus-divider after the udc has started.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
[Alex: also fixed a signed one-bit bitfield a whitespace error and yet
 another set of line-too-long and void pointer casting errors]
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No functional change. Replace *_* with *-* in property names of otg to
follow the general convention.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Adding PHY driver support for USB 3.0 controller for Samsung's
SoCs.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Moving register and structure definitions to header file,
and keeping the generic functions to be used across
multiple PHYs in common phy helper driver under SAMSUNG_USBPHY,
and moving USB 2.0 PHY driver under SAMSUNG_USB2PHY.

Also allowing samsung PHY drivers be built as modules.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Includes few minor fixes in dwc3-omap like populating the compatible
string in a correct way, extracting the utmi-mode property properly and
changing the index of get_irq since irq of core is removed from hwmod
entry.

Also updated the documentation with dwc3-omap device tree binding
information.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

[ balbi@ti.com : fix a compile warning introduced by
	this commit ]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The PHY clock, clock rate, VCC regulator and RESET regulator
can now be provided via device tree.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Allows the OMAP EHCI controller to be specified via device tree.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allows the OHCI controller found in OMAP3 and later chips to
be specified via device tree.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding OHCI device tree node for Exynos5250 along with
the device base address.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adding EHCI device tree node for Exynos5250 along with
the device base adress and gpio line for vbus.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

As reset GPIO information is PHY specific detail, adding
it to PHY DT node.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add DT nodes for Tegra USB PHY along with related documentation.
Also added a phandle property to controller DT node, for referring
to connected PHY instance.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

As Tegra USB host driver is using instance number for resetting
PORT0 twice, adding a new DT property for handling this.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Added dt support for dwc3 core and update the documentation with
device tree binding information. Getting a PHY is now done using
devm_usb_get_phy_by_phandle() for dt boot.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added a driver for usb3 phy that handles the interaction between usb phy
device and dwc3 controller.

This also includes device tree support for usb3 phy driver and
the documentation with device tree binding information is updated.

Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Start using the control module driver for powering on the PHY and for
writing to the mailbox instead of writing to the control module
registers on their own.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added a new driver for the usb part of control module. This has an API
to power on the USB2 phy and an API to write to the mailbox depending on
whether MUSB has to act in host mode or in device mode.

Writing to control module registers for doing the above task which was
previously done in omap glue and in omap-usb2 phy will be removed.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added device tree support for usb3503 driver and add new document with device tree binding information.
Signed-off-by: NDongjin Kim <tobetter@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds host phy support to samsung-usbphy driver and
further adds support for samsung's exynos5250 usb-phy.
Signed-off-by: NPraveen Paneri <p.paneri@samsung.com>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Adding support to parse device node data in order to get
required properties to set pmu isolation for usb-phy.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This driver uses usb_phy interface to interact with s3c-hsotg. Supports
phy_init and phy_shutdown functions to enable/disable usb phy. Support
will be extended to host controllers and more Samsung SoCs.
Signed-off-by: NPraveen Paneri <p.paneri@samsung.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Based on previous work by Michael Walle and Jason Cooper.

Made their work actually work, which required added interrupt from DT
and auxdata, along with setting the dma_mask, which DT does not
currently do.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

DT bindings normally use '-' (hyphens) instead of '_' (underscore),
driver has it the proper way, but binding documentation does not
reflect it, fix it.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

OMAP2+ family of devices are now obtaining resources via DT, earlier
it was obtained from hwmod. Update binding document accrodingly, while
at it add example.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Bindings for gpio, interrupt controller, power management controller,
timer, realtime clock, serial uart, ehci and uhci controllers and
framebuffer controllers used on the arch-vt8500 platform.

Framebuffer binding also specifies a 'display' node which is required
for determining the lcd panel data.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>