DCC commands are not protected with the RTNL lock, so a mutex should be added
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When working with DCC, a function can be disabled or enabled (virtual link down
or up). Using the function state introduced some race conditions with the
load/unload flow.
Using a separate flag to indicate that the function is disabled.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Value of zero was used to disable the fairness mechanism. Though the code
(driver and FW) allowed changing the value at run time, it did not allow to do
that if the mechanism was disabled to begin with.
Fixed the FW to allow turning on and off the mechanism at run time. Fixed the
code to read the value from the chip at the right sequence.
Without this fix, if the initial value was set to zero, traffic could not run on
the interface.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the main CNIC registration, callback, MAC addr. setup functions.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NShmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to initialize hardware blocks used for iSCSI.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NShmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For iSCSI MAC address setup in later patches.
Signed-off-by: NShmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the SPQ (slow-path queue) operations will be used
by the cnic code in later patches.
Signed-off-by: NShmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These string query operations were supposed to be replaced by the
generic get_sset_count() starting in 2007.  Convert the remaining
implementations.

Also remove calls to these operations to initialise drvinfo->n_stats.
The ethtool core code already does that.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to put ethtool_ops in data, they should be const.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a couple of cases collapse some extra code like:
   int retval = NETDEV_TX_OK;
   ...
   return retval;
into
   return NETDEV_TX_OK;
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving the code to a more logical place and beautifying it. No real change in
behavior.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this check, when running out of memory, we will see PSOD's in
bnx2x_init_fill() when doing a memset().  This is because at that time,
bp->gunzip_buf is not pointing to a valid allocated space.
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved the dmae_command from the heap to the stack.  This will save 56
bytes per bnx2x structure.   As a side benefit, we can also reduce the
time the dmae_mutex is held.  This is because do we not need to hold
this mutex when setting up the dmae command.  The memory where is dmae
command is stored is not a shared resource and doesn not need to be
protected.
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move printing of version from probe to the init function
Rather then checking if this is the first module probe call to print
the version of the driver only once, the statement is moved to the init
function of the module where init is only called once
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions bnx2x_get_pcie_width() and bnx2x_get_pcie_speed() were
combined into bnx2x_get_pcie_width_speed() so that there is only
1 PCI read to PCICFG_OFFSET + PCICFG_LINK_CONTROL rather then 2 reads.
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, bnx2x_init_dev calls pci_set_drvdata(pdev, NULL)
Signed-off-by: NYitchak Gertner <gertner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a given ring is running out of space, the FW can send pause towards the
network. When working with multi-queues, when one queue is getting out of space
it can block all other queues. The preferred scheme is to send pause frames only
when running out of the shared internal chip buffers and if a given queue cannot
place a packet on the host, it will drop it. Since some users might want to work
in drop-less mode, allowing changing the behavior as a module parameter.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is required for NCSI statistics
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are 3 operations that the driver needs to support to allow applications to
access the PHY FW (on top of the MDC/MDIO access). Since those are essentially
nvram access commands, adding them to the ethtool -E interface.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by Ben Hutchings <bhutchings@solarflare.com>, using the MDC/MDIO
IOCTL
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In multi-function mode, the FW can receive special management control commands
to set the Min/Max BW and the the function link state
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new FW improves the packets per second rate. It required a lot of change in
the FW which implies many changes in the driver to support it. It is now also
possible for the driver to use a separate MSI-X vector for Rx and Tx - this also
add some to the complicity of this change.

All things said - after this patch, practically all performance matrixes show
improvement.
Though Vladislav Zolotarov is not signed on this patch, he did most of the job
and deserves credit for that.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI drivers that implement the struct pci_error_handlers' error_detected
callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure. This patch fixes the issue for bnx2x.
Signed-off-by: NDean Nelson <dnelson@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some cases with 57711E, depending on the functions unload sequence, other
functions MAC address could have been used to wake the system as well. Make sure
to block all but the current function if WoL is required by changing the mode
to single function WoL.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Self test used to play with the management FIFO possibly while management was
running...
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to lack of configuration, if the BMC configures the chip to pass all
broadcast/multicast traffic to it, the host will not receive it. On top of
fixing it, also make sure that in promiscuous mode, the host will receive the
management traffic as well.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patrick said : "vlan_features doesn't need to be updated, the resulting
dev->features of the VLAN device is computed as the intersection of
dev->features and dev->vlan_features."
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>