When the name of the given entry is empty , the state needs to be
updated accordingly.

Cc: stable@vger.kernel.org
Signed-off-by: NRam Malovany <ramm@ti.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

If the device was not found in a list of found devices names of which
are pending.This may happen in a case when HCI Remote Name Request
was sent as a part of incoming connection establishment procedure.
Hence there is no need to continue resolving a next name as it will
be done upon receiving another Remote Name Request Complete Event.
This will fix a kernel crash when trying to use this entry to resolve
the next name.

Cc: stable@vger.kernel.org
Signed-off-by: NRam Malovany <ramm@ti.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

If entry wasn't found in the hci_inquiry_cache_lookup_resolve do not
resolve the name.This will fix a kernel crash when trying to use NULL
pointer.

Cc: stable@vger.kernel.org
Signed-off-by: NRam Malovany <ramm@ti.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Some devices e.g. some Android based phones don't do SDP search before
pairing and cancel legacy pairing when ACL is disconnected.

PIN Code Request event which changes ACL timeout to HCI_PAIRING_TIMEOUT
is only received after remote user entered PIN.

In that case no L2CAP is connected so default HCI_DISCONN_TIMEOUT
(2 seconds) is being used to timeout ACL connection. This results in
problems with legacy pairing as remote user has only few seconds to
enter PIN before ACL is disconnected.

Increase disconnect timeout for incomming connection to
HCI_PAIRING_TIMEOUT if SSP is disabled and no linkey exists.

To avoid keeping ACL alive for too long after SDP search set ACL
timeout back to HCI_DISCONN_TIMEOUT when L2CAP is connected.

2012-07-19 13:24:43.413521 < HCI Command: Create Connection (0x01|0x0005) plen 13
    bdaddr 00:02:72:D6:6A:3F ptype 0xcc18 rswitch 0x01 clkoffset 0x0000
    Packet type: DM1 DM3 DM5 DH1 DH3 DH5
2012-07-19 13:24:43.425224 > HCI Event: Command Status (0x0f) plen 4
    Create Connection (0x01|0x0005) status 0x00 ncmd 1
2012-07-19 13:24:43.885222 > HCI Event: Role Change (0x12) plen 8
    status 0x00 bdaddr 00:02:72:D6:6A:3F role 0x01
    Role: Slave
2012-07-19 13:24:44.054221 > HCI Event: Connect Complete (0x03) plen 11
    status 0x00 handle 42 bdaddr 00:02:72:D6:6A:3F type ACL encrypt 0x00
2012-07-19 13:24:44.054313 < HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
    handle 42
2012-07-19 13:24:44.055176 > HCI Event: Page Scan Repetition Mode Change (0x20) plen 7
    bdaddr 00:02:72:D6:6A:3F mode 0
2012-07-19 13:24:44.056217 > HCI Event: Max Slots Change (0x1b) plen 3
    handle 42 slots 5
2012-07-19 13:24:44.059218 > HCI Event: Command Status (0x0f) plen 4
    Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 0
2012-07-19 13:24:44.062192 > HCI Event: Command Status (0x0f) plen 4
    Unknown (0x00|0x0000) status 0x00 ncmd 1
2012-07-19 13:24:44.067219 > HCI Event: Read Remote Supported Features (0x0b) plen 11
    status 0x00 handle 42
    Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
2012-07-19 13:24:44.067248 < HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3
    handle 42 page 1
2012-07-19 13:24:44.071217 > HCI Event: Command Status (0x0f) plen 4
    Read Remote Extended Features (0x01|0x001c) status 0x00 ncmd 1
2012-07-19 13:24:44.076218 > HCI Event: Read Remote Extended Features (0x23) plen 13
    status 0x00 handle 42 page 1 max 1
    Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
2012-07-19 13:24:44.076249 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
    bdaddr 00:02:72:D6:6A:3F mode 2 clkoffset 0x0000
2012-07-19 13:24:44.081218 > HCI Event: Command Status (0x0f) plen 4
    Remote Name Request (0x01|0x0019) status 0x00 ncmd 1
2012-07-19 13:24:44.105214 > HCI Event: Remote Name Req Complete (0x07) plen 255
    status 0x00 bdaddr 00:02:72:D6:6A:3F name 'uw000951-0'
2012-07-19 13:24:44.105284 < HCI Command: Authentication Requested (0x01|0x0011) plen 2
    handle 42
2012-07-19 13:24:44.111207 > HCI Event: Command Status (0x0f) plen 4
    Authentication Requested (0x01|0x0011) status 0x00 ncmd 1
2012-07-19 13:24:44.112220 > HCI Event: Link Key Request (0x17) plen 6
    bdaddr 00:02:72:D6:6A:3F
2012-07-19 13:24:44.112249 < HCI Command: Link Key Request Negative Reply (0x01|0x000c) plen 6
    bdaddr 00:02:72:D6:6A:3F
2012-07-19 13:24:44.115215 > HCI Event: Command Complete (0x0e) plen 10
    Link Key Request Negative Reply (0x01|0x000c) ncmd 1
    status 0x00 bdaddr 00:02:72:D6:6A:3F
2012-07-19 13:24:44.116215 > HCI Event: PIN Code Request (0x16) plen 6
    bdaddr 00:02:72:D6:6A:3F
2012-07-19 13:24:48.099184 > HCI Event: Auth Complete (0x06) plen 3
    status 0x13 handle 42
    Error: Remote User Terminated Connection
2012-07-19 13:24:48.179182 > HCI Event: Disconn Complete (0x05) plen 4
    status 0x00 handle 42 reason 0x13
    Reason: Remote User Terminated Connection

Cc: stable@vger.kernel.org
Signed-off-by: NSzymon Janc <szymon.janc@tieto.com>
Acked-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

sco_chan_del() only has conn != NULL when called from sco_conn_del() so
just move the code from it that deal with conn to sco_conn_del().

[  120.765529]
[  120.765529] ======================================================
[  120.766529] [ INFO: possible circular locking dependency detected ]
[  120.766529] 3.5.0-rc1-10292-g3701f944-dirty #70 Tainted: G        W
[  120.766529] -------------------------------------------------------
[  120.766529] kworker/u:3/1497 is trying to acquire lock:
[  120.766529]  (&(&conn->lock)->rlock#2){+.+...}, at:
[<ffffffffa00b7ecc>] sco_chan_del+0x4c/0x170 [bluetooth]
[  120.766529]
[  120.766529] but task is already holding lock:
[  120.766529]  (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}, at:
[<ffffffffa00b8401>] sco_conn_del+0x61/0xe0 [bluetooth]
[  120.766529]
[  120.766529] which lock already depends on the new lock.
[  120.766529]
[  120.766529]
[  120.766529] the existing dependency chain (in reverse order) is:
[  120.766529]
[  120.766529] -> #1 (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}:
[  120.766529]        [<ffffffff8107980e>] lock_acquire+0x8e/0xb0
[  120.766529]        [<ffffffff813c19e0>] _raw_spin_lock+0x40/0x80
[  120.766529]        [<ffffffffa00b85e9>] sco_connect_cfm+0x79/0x300
[bluetooth]
[  120.766529]        [<ffffffffa0094b13>]
hci_sync_conn_complete_evt.isra.90+0x343/0x400 [bluetooth]
[  120.766529]        [<ffffffffa009d447>] hci_event_packet+0x317/0xfb0
[bluetooth]
[  120.766529]        [<ffffffffa008aa68>] hci_rx_work+0x2c8/0x890
[bluetooth]
[  120.766529]        [<ffffffff81047db7>] process_one_work+0x197/0x460
[  120.766529]        [<ffffffff810489d6>] worker_thread+0x126/0x2d0
[  120.766529]        [<ffffffff8104ee4d>] kthread+0x9d/0xb0
[  120.766529]        [<ffffffff813c4294>] kernel_thread_helper+0x4/0x10
[  120.766529]
[  120.766529] -> #0 (&(&conn->lock)->rlock#2){+.+...}:
[  120.766529]        [<ffffffff81078a8a>] __lock_acquire+0x154a/0x1d30
[  120.766529]        [<ffffffff8107980e>] lock_acquire+0x8e/0xb0
[  120.766529]        [<ffffffff813c19e0>] _raw_spin_lock+0x40/0x80
[  120.766529]        [<ffffffffa00b7ecc>] sco_chan_del+0x4c/0x170
[bluetooth]
[  120.766529]        [<ffffffffa00b8414>] sco_conn_del+0x74/0xe0
[bluetooth]
[  120.766529]        [<ffffffffa00b88a2>] sco_disconn_cfm+0x32/0x60
[bluetooth]
[  120.766529]        [<ffffffffa0093a82>]
hci_disconn_complete_evt.isra.53+0x242/0x390 [bluetooth]
[  120.766529]        [<ffffffffa009d747>] hci_event_packet+0x617/0xfb0
[bluetooth]
[  120.766529]        [<ffffffffa008aa68>] hci_rx_work+0x2c8/0x890
[bluetooth]
[  120.766529]        [<ffffffff81047db7>] process_one_work+0x197/0x460
[  120.766529]        [<ffffffff810489d6>] worker_thread+0x126/0x2d0
[  120.766529]        [<ffffffff8104ee4d>] kthread+0x9d/0xb0
[  120.766529]        [<ffffffff813c4294>] kernel_thread_helper+0x4/0x10
[  120.766529]
[  120.766529] other info that might help us debug this:
[  120.766529]
[  120.766529]  Possible unsafe locking scenario:
[  120.766529]
[  120.766529]        CPU0                    CPU1
[  120.766529]        ----                    ----
[  120.766529]   lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
[  120.766529]
lock(&(&conn->lock)->rlock#2);
[  120.766529]
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
[  120.766529]   lock(&(&conn->lock)->rlock#2);
[  120.766529]
[  120.766529]  *** DEADLOCK ***
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Patch adds support for BCM20702A0 device id (0a5c:21f4).

usb-devices after patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

usb-devices before patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Tested-by: NChris Gagnon <chris.gagnon@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

AR1111 is same as AR9485. The h/w
difference between them is quite insignificant,
Felix suggests only very few baseband features
may not be available in AR1111. The h/w code for
AR9485 is already present, so AR1111 should
work fine with the addition of its PID/VID.

Cc: stable@vger.kernel.org [2.6.39+]
Cc: Felix Bitterli <felixb@qca.qualcomm.com>
Reported-by: NTim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: NTim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmsmac cannot call freq_reg_info() during channel changes as it does
not hold cfg80211_lock, and as a result it generates a lockdep warning.
freq_reg_info() is being used to determine whether OFDM is allowed on
the current channel, so we can avoid the errant call by using the new
IEEE80211_CHAN_NO_OFDM for this purpose instead.
Reported-by: NJosh Boyer <jwboyer@redhat.com>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The if_sdio_card structure was never being freed, and neither
was the command structure used for association.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is going to fix the resuming failed from S3/S4
for rt3290 chip.
Signed-off-by: NWoody Hung <Woody.Hung@mediatek.com>
Cc: Kevin Chou <kevin.chou@mediatek.com>
Signed-off-by: NChen, Chien-Chia <machen@suse.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On an OLPC XO-1.5 we have seen the following situation:
 - the system starts going into suspend
 - no wake params are set, so the mmc layer removes the card
 - during remove, we send a command to the card
 - that command fails, causing if_sdio's reset method to try and remove
   the mmc card in attempt to reset it
 - the mmc layer is not happy about being asked to remove a card that
   it is already removing, and the kernel crashes

While the MMC layer could possibly be taught to behave better here,
it also seems sensible for libertas not to try and reset a card if
we're in the process of removing it anyway.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add some comments by the way
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Restore the default state to the "beacon_found" flag when
the channel flags are restored.  Otherwise, we can end up
with a channel that we can no longer transmit on even when
we can see beacons on that channel.
Signed-off-by: NPaul Stewart <pstew@chromium.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently the only way for wireless drivers to tell whether or not OFDM
is allowed on the current channel is to check the regulatory
information. However, this requires hodling cfg80211_mutex, which is not
visible to the drivers.

Other regulatory restrictions are provided as flags in the channel
definition, so let's do similarly with OFDM. This patch adds a new flag,
IEEE80211_CHAN_NO_OFDM, to tell drivers that OFDM on a channel is not
allowed. This flag is set on any channels for which regulatory indicates
that OFDM is prohibited.
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Tested-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove unused includes after IP cache removal
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnx2x_mcast_enqueue_cmd() we'll leak the memory allocated to
'new_cmd' if we hit the deafault case of the 'switch (cmd)'.
Add a 'kfree(new_cmd)' to that case to avoid the leak.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After SA is setup, one timer is armed to detect soft/hard expiration,
however the timer handler uses xtime to do the math. This makes hard
expiration occurs first before soft expiration after setting new date
with big interval. As a result new child SA is deleted before rekeying
the new one.
Signed-off-by: NFan Du <fdu@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cache the device gso_max_segs in sock::sk_gso_max_segs and use it to
limit the size of TSO skbs.  This avoids the need to fall back to
software GSO for local TCP senders.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently an skb requiring TSO may not fit within a minimum-size TX
queue.  The TX queue selected for the skb may stall and trigger the TX
watchdog repeatedly (since the problem skb will be retried after the
TX reset).  This issue is designated as CVE-2012-3412.

Set the maximum number of TSO segments for our devices to 100.  This
should make no difference to behaviour unless the actual MSS is less
than about 700.  Increase the minimum TX queue size accordingly to
allow for 2 worst-case skbs, so that there will definitely be space
to add an skb after we wake a queue.

To avoid invalidating existing configurations, change
efx_ethtool_set_ringparam() to fix up values that are too small rather
than returning -EINVAL.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A peer (or local user) may cause TCP to use a nominal MSS of as little
as 88 (actual MSS of 76 with timestamps).  Given that we have a
sufficiently prodigious local sender and the peer ACKs quickly enough,
it is nevertheless possible to grow the window for such a connection
to the point that we will try to send just under 64K at once.  This
results in a single skb that expands to 861 segments.

In some drivers with TSO support, such an skb will require hundreds of
DMA descriptors; a substantial fraction of a TX ring or even more than
a full ring.  The TX queue selected for the skb may stall and trigger
the TX watchdog repeatedly (since the problem skb will be retried
after the TX reset).  This particularly affects sfc, for which the
issue is designated as CVE-2012-3412.

Therefore:
1. Add the field net_device::gso_max_segs holding the device-specific
   limit.
2. In netif_skb_features(), if the number of segments is too high then
   mask out GSO features to force fall back to software GSO.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull MIPS updates from Ralf Baechle:
 "The lion share of this pull request are fixes for clk-related breakage
  caused by other changes during this merge window.  For some platforms
  the fix was as simple as selecting HAVE_CLK, for others like the
  Loongson 2 significant restructuring was required.

  The remainder are changes required to get the Lantiq code to work
  again."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Loongson 2: Sort out clock managment.
  MIPS: Loongson 1: more clk support and add select HAVE_CLK
  MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: Lantiq: Platform specific CLK fixup
  MIPS: Lantiq: Add device_tree_init function
  MIPS: Lantiq: Fix interface clock and PCI control register offset

Pull UML fixes from Richard Weinberger:
 "This patch set contains mostly fixes and cleanups.  The UML tty driver
  uses now tty_port and is no longer broken like hell  :-)"

* 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Add arch/x86/um to MAINTAINERS
  um: pass siginfo to guest process
  um: fix ubd_file_size for read-only files
  um: pull interrupt_end() into userspace()
  um: split syscall_trace(), pass pt_regs to it
  um: switch UPT_SET_RETURN_VALUE and regs_return_value to pt_regs
  um: set BLK_CGROUP=y in defconfig
  um: remove count_lock
  um: fully use tty_port
  um: Remove dead code
  um: remove line_ioctl()
  TTY: um/line, use tty from tty_port
  TTY: um/line, add tty_port

Pull ARM DMA engine updates from Russell King:
 "This looks scary at first glance, but what it is is:
   - a rework of the sa11x0 DMA engine driver merged during the previous
     cycle, to extract a common set of helper functions for DMA engine
     implementations.
   - conversion of amba-pl08x.c to use these helper functions.
   - addition of OMAP DMA engine driver (using these helper functions),
     and conversion of some of the OMAP DMA users to use DMA engine.

  Nothing in the helper functions is ARM specific, so I hope that other
  implementations can consolidate some of their code by making use of
  these helpers.

  This has been sitting in linux-next most of the merge cycle, and has
  been tested by several OMAP folk.  I've tested it on sa11x0 platforms,
  and given it my best shot on my broken platforms which have the
  amba-pl08x controller.

  The last point is the addition to feature-removal-schedule.txt, which
  will have a merge conflict.  Between myself and TI, we're planning to
  remove the old TI DMA implementation next year."

Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}

* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
  ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
  ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
  Add feature removal of old OMAP private DMA implementation
  mtd: omap2: remove private DMA API implementation
  mtd: omap2: add DMA engine support
  spi: omap2-mcspi: remove private DMA API implementation
  spi: omap2-mcspi: add DMA engine support
  ARM: omap: remove mmc platform data dma_mask and initialization
  mmc: omap: remove private DMA API implementation
  mmc: omap: add DMA engine support
  mmc: omap_hsmmc: remove private DMA API implementation
  mmc: omap_hsmmc: add DMA engine support
  dmaengine: omap: add support for cyclic DMA
  dmaengine: omap: add support for setting fi
  dmaengine: omap: add support for returning residue in tx_state method
  dmaengine: add OMAP DMA engine driver
  dmaengine: sa11x0-dma: add cyclic DMA support
  dmaengine: sa11x0-dma: fix DMA residue support
  dmaengine: PL08x: ensure all descriptors are freed when channel is released
  dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
  ...

Pull ARM audit/signal updates from Russell King:
 "ARM audit/signal handling updates from Al and Will.  This improves on
  the work Viro did last merge window, and sorts out some of the issues
  found with that work."

* 'audit' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7475/1: sys_trace: allow all syscall arguments to be updated via ptrace
  ARM: 7474/1: get rid of TIF_SYSCALL_RESTARTSYS
  ARM: 7473/1: deal with handlerless restarts without leaving the kernel
  ARM: 7472/1: pull all work_pending logics into C function
  ARM: 7471/1: Revert "7442/1: Revert "remove unused restart trampoline""
  ARM: 7470/1: Revert "7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK""

Pull ARM fixes from Russell King:
 "This fixes various issues found during July"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7479/1: mm: avoid NULL dereference when flushing gate_vma with VIVT caches
  ARM: Fix undefined instruction exception handling
  ARM: 7480/1: only call smp_send_stop() on SMP
  ARM: 7478/1: errata: extend workaround for erratum #720789
  ARM: 7477/1: vfp: Always save VFP state in vfp_pm_suspend on UP
  ARM: 7476/1: vfp: only clear vfp state for current cpu in vfp_pm_suspend
  ARM: 7468/1: ftrace: Trace function entry before updating index
  ARM: 7467/1: mutex: use generic xchg-based implementation for ARMv6+
  ARM: 7466/1: disable interrupt before spinning endlessly
  ARM: 7465/1: Handle >4GB memory sizes in device tree and mem=size@start option

Signed-off-by: NRichard Weinberger <richard@nod.at>

UML guest processes now get correct siginfo_t for SIGTRAP, SIGFPE,
SIGILL and SIGBUS. Specifically, si_addr and si_code are now correct
where previously they were si_addr = NULL and si_code = 128.
Signed-off-by: NMartin Pärtel <martin.partel@gmail.com>
Signed-off-by: NRichard Weinberger <richard@nod.at>

Made ubd_file_size not request write access. Fixes use of read-only images.
Signed-off-by: NMartin Pärtel <martin.partel@gmail.com>
Signed-off-by: NRichard Weinberger <richard@nod.at>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NRichard Weinberger <richard@nod.at>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
[richard@nod.at: Fixed some minor build issues]
Signed-off-by: NRichard Weinberger <richard@nod.at>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NRichard Weinberger <richard@nod.at>

The mesh path timer needs to be canceled when
leaving the mesh as otherwise it could fire
after the interface has been removed already.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's a corner case that can happen when we
suspend with a timer running, then resume and
disconnect. If we connect again, suspend and
resume we might start timers that shouldn't be
running. Reset the timer flags to avoid this.

This affects both mesh and managed modes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Pull fbdev updates from Florian Tobias Schandinat:
 - large updates for OMAP
   - support for LCD3 overlay manager (omap5)
   - omapdss output cleanup
   - removal of passive matrix LCD support as there are no drivers for
     such panels for DSS or DSS2 and nobody complained (cleanup)
 - large updates for SH Mobile
   - overlay support
   - separating MERAM (cache) from framebuffer driver
 - some updates for Exynos and da8xx-fb
 - various other small patches

* tag 'fbdev-updates-for-3.6' of git://github.com/schandinat/linux-2.6: (78 commits)
  da8xx-fb: fix compile issue due to missing include
  fbdev: Make pixel_to_pat() failure mode more friendly
  da8xx-fb: do not turn ON LCD backlight unless LCDC is enabled
  fbdev: sh_mobile_lcdc: Fix vertical panning step
  video: exynos mipi dsi: Fix mipi dsi regulators handling issue
  video: da8xx-fb: do clock reset of revision 2 LCDC before enabling
  arm: da850: configure LCDC fifo threshold
  video: da8xx-fb: configure FIFO threshold to reduce underflow errors
  video: da8xx-fb: fix flicker due to 1 frame delay in updated frame
  video: da8xx-fb rev2: fix disabling of palette completion interrupt
  da8xx-fb: add missing FB_BLANK operations
  video: exynos_dp: use usleep_range instead of delay
  video: exynos_dp: check the only INTERLANE_ALIGN_DONE bit during Link Training
  fb: epson1355fb: Fix section mismatch
  video: exynos_dp: fix wrong DPCD address during Link Training
  video/smscufx: fix line counting in fb_write
  aty128fb: Fix coding style issues
  fbdev: sh_mobile_lcdc: Fix pan offset computation in YUV mode
  fbdev: sh_mobile_lcdc: Fix overlay registers update during pan operation
  fbdev: sh_mobile_lcdc: Support horizontal panning
  ...

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes that have been found recently.  Most of
  the commits are regression fixes in HD-audio and some other random
  drivers."

* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: snd-usb: fix clock source validity index
  ALSA: hda - Fix mute-LED GPIO initialization for IDT codecs
  ALSA: hda - Add descriptions for missing IDT 92HD83x models
  ALSA: hda - Fix polarity of mute LED on HP Mini 210
  ALSA: es1688 - freeup resources on init failure
  ALSA: hda - Workaround for silent output on VAIO Z with ALC889
  ALSA: hda - Fix WARNING from HDMI/DP parser
  ALSA: hda - Detach from converter at closing in patch_hdmi.c
  ALSA: hda - Fix mute-LED GPIO setup for HP Mini 210
  ALSA: mpu401: Fix missing initialization of irq field
  ALSA: hda - Fix invalid D3 of headphone DAC on VT202x codecs

Pull second vfs pile from Al Viro:
 "The stuff in there: fsfreeze deadlock fixes by Jan (essentially, the
  deadlock reproduced by xfstests 068), symlink and hardlink restriction
  patches, plus assorted cleanups and fixes.

  Note that another fsfreeze deadlock (emergency thaw one) is *not*
  dealt with - the series by Fernando conflicts a lot with Jan's, breaks
  userland ABI (FIFREEZE semantics gets changed) and trades the deadlock
  for massive vfsmount leak; this is going to be handled next cycle.
  There probably will be another pull request, but that stuff won't be
  in it."

Fix up trivial conflicts due to unrelated changes next to each other in
drivers/{staging/gdm72xx/usb_boot.c, usb/gadget/storage_common.c}

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
  delousing target_core_file a bit
  Documentation: Correct s_umount state for freeze_fs/unfreeze_fs
  fs: Remove old freezing mechanism
  ext2: Implement freezing
  btrfs: Convert to new freezing mechanism
  nilfs2: Convert to new freezing mechanism
  ntfs: Convert to new freezing mechanism
  fuse: Convert to new freezing mechanism
  gfs2: Convert to new freezing mechanism
  ocfs2: Convert to new freezing mechanism
  xfs: Convert to new freezing code
  ext4: Convert to new freezing mechanism
  fs: Protect write paths by sb_start_write - sb_end_write
  fs: Skip atime update on frozen filesystem
  fs: Add freezing handling to mnt_want_write() / mnt_drop_write()
  fs: Improve filesystem freezing handling
  switch the protection of percpu_counter list to spinlock
  nfsd: Push mnt_want_write() outside of i_mutex
  btrfs: Push mnt_want_write() outside of i_mutex
  fat: Push mnt_want_write() outside of i_mutex
  ...

For unexplainable reasons the Loongson 2 clock API was implemented in a
module so fixing this involved shifting large amounts of code around.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Pull block driver changes from Jens Axboe:

 - Making the plugging support for drivers a bit more sane from Neil.
   This supersedes the plugging change from Shaohua as well.

 - The usual round of drbd updates.

 - Using a tail add instead of a head add in the request completion for
   ndb, making us find the most completed request more quickly.

 - A few floppy changes, getting rid of a duplicated flag and also
   running the floppy init async (since it takes forever in boot terms)
   from Andi.

* 'for-3.6/drivers' of git://git.kernel.dk/linux-block:
  floppy: remove duplicated flag FD_RAW_NEED_DISK
  blk: pass from_schedule to non-request unplug functions.
  block: stack unplug
  blk: centralize non-request unplug handling.
  md: remove plug_cnt feature of plugging.
  block/nbd: micro-optimization in nbd request completion
  drbd: announce FLUSH/FUA capability to upper layers
  drbd: fix max_bio_size to be unsigned
  drbd: flush drbd work queue before invalidate/invalidate remote
  drbd: fix potential access after free
  drbd: call local-io-error handler early
  drbd: do not reset rs_pending_cnt too early
  drbd: reset congestion information before reporting it in /proc/drbd
  drbd: report congestion if we are waiting for some userland callback
  drbd: differentiate between normal and forced detach
  drbd: cleanup, remove two unused global flags
  floppy: Run floppy initialization asynchronous