Since 952c5ca1 (fsl_pq_mdio: Clean up tbi address configuration) .probe returns
-EBUSY when the "tbi-phy" node is missing. Fix this.

Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds listen only mode to the mscan controller.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.

Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support enabling/disabling/querying internal loopback mode for
forcedeth NICs using ethtool.
Signed-off-by: NSanjay Hortikar <horti@google.com>
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces new network device called team. It supposes to be
very fast, simple, userspace-driven alternative to existing bonding
driver.

Userspace library called libteam with couple of demo apps is available
here:
https://github.com/jpirko/libteam
Note it's still in its dipers atm.

team<->libteam use generic netlink for communication. That and rtnl
suppose to be the only way to configure team device, no sysfs etc.

Python binding of libteam was recently introduced.
Daemon providing arpmon/miimon active-backup functionality will be
introduced shortly. All what's necessary is already implemented in
kernel team driver.

v7->v8:
	- check ndo_ndo_vlan_rx_[add/kill]_vid functions before calling
	  them.
	- use dev_kfree_skb_any() instead of dev_kfree_skb()

v6->v7:
	- transmit and receive functions are not checked in hot paths.
	  That also resolves memory leak on transmit when no port is
	  present

v5->v6:
	- changed couple of _rcu calls to non _rcu ones in non-readers

v4->v5:
	- team_change_mtu() uses team->lock while travesing though port
	  list
	- mac address changes are moved completely to jurisdiction of
	  userspace daemon. This way the daemon can do FOM1, FOM2 and
	  possibly other weird things with mac addresses.
	  Only round-robin mode sets up all ports to bond's address then
	  enslaved.
	- Extended Kconfig text

v3->v4:
	- remove redundant synchronize_rcu from __team_change_mode()
	- revert "set and clear of mode_ops happens per pointer, not per
	  byte"
	- extend comment of function __team_change_mode()

v2->v3:
	- team_change_mtu() uses rcu version of list traversal to unwind
	- set and clear of mode_ops happens per pointer, not per byte
	- port hashlist changed to be embedded into team structure
	- error branch in team_port_enter() does cleanup now
	- fixed rtln->rtnl

v1->v2:
	- modes are made as modules. Makes team more modular and
	  extendable.
	- several commenters' nitpicks found on v1 were fixed
	- several other bugs were fixed.
	- note I ignored Eric's comment about roundrobin port selector
	  as Eric's way may be easily implemented as another mode (mode
	  "random") in future.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The race may cause access of registers while MAC hw block is
in reset state. As a result syslog will show error messages.
We can prevent this by using state from local variable.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shut down the device in case of fan failure to prevent HW damage.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need propagate the DCBX results from PMF to other functions
on the same port, in order to properly update netdev structure
and allow following new ETS and PFC configurations.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FCoE license info must be initialized at probe(), but
iSCSI at open().
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A FW cmd timeout (with a sufficiently large timeout value in the
order of tens of seconds) indicates an unresponsive FW. In this state
issuing further cmds and waiting for a completion will only stall the process.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we're spamming error messages each time a FW cmd call is made
while in EEH/UE error state. One log msg on error detection is enough.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize if_handle, vf_if_handle and vf_pmac_id with "-1" so that in
failure cases when be_clear() is called, we can skip over
if_destroy/pmac_del cmds if they have not been created.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables the ioctl support for the driver. So userspace
programs like mii-tool can work.

Resend in merge window
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tunnels can force an alignment of their percpu data to reduce number of
cache lines used in fast path, or read in .ndo_get_stats()

percpu_alloc() is a very fine grained allocator, so any small hole will
be used anyway.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To prevent the SBus driver for Sun Happy Meal cards from being loaded for
PCI cards utilizing the same chipset, a filter was added to the probe
function in commit 0b492fce.

The filter was implemented by checking the name of the parent node in
the OF tree. This patch extends this filter, so that the driver will
load on SBus systems that are based upon SBI SBus Bridges.
Signed-off-by: NKjetil Oftedal <oftedal@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver used NET_IP_ALIGN to remove some additional padding inside of
the rx_fixup function. On many architectures NET_IP_ALIGN defaults to 2
which removed the correct amount of bytes.

On MCORE2-machines commit ea812ca1
introduces a change which sets NET_IP_ALIGN to 0 by default. Which
triggered the bug on these machines.

This fix introduces a new RXW_PADDING define and uses this instead of
NET_IP_ALIGN. The name was taken from the original SMSC7500 driver which
is provided by SMSC.
Signed-off-by: NNico Erfurth <ne@erfurth.eu>
Tested-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rx byte count was off; instead use the hardware's count.  Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.

- The count of transmitted packets reported by the forcedeth driver
  reports pre-TSO (TCP Segmentation Offload) packet counts and not the
  count of the number of packets sent on the wire. This change fixes
  the forcedeth driver to report the correct count. Fixed the code by
  copying the count stored in the NIC H/W to the value reported by the
  driver.

- Count rx_drop_frame errors as rx_fifo_errors:
  We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
  for too long.  Normally, rx_fifo_errors would be counted in this case.
  The rx_drop_frame error count is private to forcedeth and is not
  reported by ifconfig or sysfs.  The rx_fifo_errors count is currently
  unused in the forcedeth driver.  It is reported by ifconfig as overruns.
  This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function ndo_get_stats() updates most of the stats from hardware
registers, making the manual updates un-needed. This change removes
these manual updates. Main exception is rx_missed_errors which needs
manual update.

Another exception is rx_packets, still updated manually in this commit
to make sure this patch doesn't change behavior of driver. This will
be addressed by a future patch.
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to avoid a race, accidentally acknowledging an interrupt that
we didn't notice and won't immediately process.  This is based solely
on code inspection; it is not known if there was an actual bug here.
Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When forcedeth module is unloaded, there exists a path that can lead
to mod_timer() after del_timer_sync(), causing an oops. This patch
short-circuits this unneeded path, which originates in
nv_get_ethtool_stats().

Tested:
  x86_64 16-way + 3 ethtool -S infinite loops + 100Mbps incoming traffic
  + rmmod/modprobe/ifconfig in a loop

Initial-Author: Salman Qazi <sqazi@google.com>
Discussion: http://patchwork.ozlabs.org/patch/123548/Signed-off-by: NDavid Decotigny <david.decotigny@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the bug added in commit v3.1-rc7-1055-gf9b491ec
SKB can be NULL at this point, at least for cdc-ncm.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix compiler errors and warnings with CONFIG_PCI_IOV defined and not
defined.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

slave->duplex is a u8 type so the in bond_info_show_slave() when we
check "if (slave->duplex == -1)", it's always false.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.

The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: NPavel Mateja <pavel@netsafe.cz>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.

Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.

Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When implementing VRRP v2 using macvlan several problems were
discovered.  VRRP is weird in that all routers participating
in a redundant group use the same virtual MAC address.
Macvlan is a natural driver to use for this but it doesn't
work.  The problem is that packets with a macvlan device's
source address are not received.

The problem is actually a regression that date back almost 2 years now.
The original problems started with:

commit 618e1b74
Author: Arnd Bergmann <arnd@arndb.de>
Date:   Thu Nov 26 06:07:10 2009 +0000

    macvlan: implement bridge, VEPA and private mode

This patches restores the original 2.6.32 behavior. Allowing multicast
packets received with the VRRP source address to be received.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.121.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>