Skip to content

K
Kernel

openeuler / Kernel
11 个月 前同步成功

通知 5
Star 0
Fork 0
K
Kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 11 4月, 2013 1 次提交
  3. 04 4月, 2013 5 次提交
  5. 03 4月, 2013 19 次提交
  7. 02 4月, 2013 10 次提交
    • L
      Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc · 118c9a45
      由 Linus Torvalds 提交于 
      Pull ARM SoC bug fixes from Arnd Bergmann:
 "After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
  sent urgent fixes for 3.9.  I pushed back on a number of them that got
  deferred to 3.10, but these are the ones that seemed important.

  Regression in 3.9:

   - Multiple regressions in OMAP2+ clock cleanup
   - SH-Mobile frame buffer bug fix that merged here because of
     maintainer MIA
   - ux500 prcmu changes broke DT booting
   - MMCI duplicated regulator setup on ux500
   - New ux500 clock driver broke ethernet on snowball
   - Local interrupt driver for mvebu broke ethernet
   - MVEBU GPIO driver did not get set up right on Orion DT
   - incorrect interrupt number on Orion crypto for DT

  Long-standing bugs, including candidates for stable:

   - Kirkwood MMC needs to disable invalid card detect pins
   - MV SDIO pinmux was wrong on Mirabox
   - GoFlex Net board file needs to set NAND chip delay
   - MSM timer restart race
   - ep93xx early debug code broke in 3.7
   - i.MX CPU hotplug race
   - Incorrect clock setup for OMAP1 USB
   - Workaround for bad clock setup by some old OMAP4 boot loaders
   - Static I/O mappings on cns3xxx since 3.2"

* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: cns3xxx: fix mapping of private memory region
  arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
  arm: orion5x: correct IRQ used in dtsi for mv_cesa
  arm: orion5x: fix orion5x.dtsi gpio parameters
  ARM: Kirkwood: fix unused mvsdio gpio pins
  arm: mvebu: Use local interrupt only for the timer 0
  ARM: kirkwood: Fix chip-delay for GoFlex Net
  ARM: ux500: Enable the clock controlling Ethernet on Snowball
  ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
  ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
  fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
  ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
  ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
  ARM: msm: Stop counting before reprogramming clockevent
  ARM: ep93xx: Fix wait for UART FIFO to be empty
  ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
  ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
  ARM: OMAP4: clock data: lock USB DPLL on boot
  ARM: OMAP1: fix USB host on 1710
      118c9a45
    • L
      Merge branch 'for-3.9' of git://linux-nfs.org/~bfields/linux · f8e9248d
      由 Linus Torvalds 提交于 
      Pull nfsd bugfix from J Bruce Fields:
 "An xdr decoding error--thanks, Toralf Förster, and Trinity!"

* 'for-3.9' of git://linux-nfs.org/~bfields/linux:
  nfsd4: reject "negative" acl lengths
      f8e9248d
    • A
      Merge tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx into fixes · 06d1d8c8
      由 Arnd Bergmann 提交于 
      From Anton Vorontsov <anton@enomsg.org>:

This tag includes Mac Lin's work to revive CNS3xxx booting:

 "Since commit 0536bdf3 (ARM: move iotable mappings within the vmalloc
 region), [...] the pre-defined iotable mappings is not in the vmalloc
 region. [...] move the iotable mappings into the vmalloc region, and
 merge the MPCore private memory region (containing the SCU, the GIC and
 the TWD) as a single region."

Plus there is a small cosmetic fix, also from Mac Lin.

* tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx:
  ARM: cns3xxx: fix mapping of private memory region

[arnd: dropped the cosmetic fix from the merge as it is not needed for 3.9]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
      06d1d8c8
    • H
      s390/mm: provide emtpy check_pgt_cache() function · 765a0cac
      由 Heiko Carstens 提交于 
      All architectures need to provide a check_pgt_cache() function. The s390 one
got lost somewhere.
So reintroduce it to prevent future compile errors e.g. if Thomas Gleixner's
idle loop rework patches get merged.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      765a0cac
    • H
      s390/uaccess: fix page table walk · ea81531d
      由 Heiko Carstens 提交于 
      When translating user space addresses to kernel addresses the follow_table()
function had two bugs:

- PROT_NONE mappings could be read accessed via the kernel mapping. That is
  e.g. putting a filename into a user page, then protecting the page with
  PROT_NONE and afterwards issuing the "open" syscall with a pointer to
  the filename would incorrectly succeed.

- when walking the page tables it used the pgd/pud/pmd/pte primitives which
  with dynamic page tables give no indication which real level of page tables
  is being walked (region2, region3, segment or page table). So in case of an
  exception the translation exception code passed to __handle_fault() is not
  necessarily correct.
  This is not really an issue since __handle_fault() doesn't evaluate the code.
  Only in case of e.g. a SIGBUS this code gets passed to user space. If user
  space can do something sane with the value is a different question though.

To fix these issues don't use any Linux primitives. Only walk the page tables
like the hardware would do it, however we leave quite some checks away since
we know that we only have full size page tables and each index is within bounds.

In theory this should fix all issues...
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      ea81531d
    • L
      Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux · fefcdbe4
      由 Linus Torvalds 提交于 
      Pull virtio fixes from Rusty Russell:
 "One reversion, a tiny leak fix, and a cc:stable locking fix, in two
  parts"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  virtio: console: add locking around c_ovq operations
  virtio: console: rename cvq_lock to c_ivq_lock
  hw_random: free rng_buffer at module exit
  Revert "virtio_console: Initialize guest_connected=true for rproc_serial"
      fefcdbe4
    • A
      loop: prevent bdev freeing while device in use · c1681bf8
      由 Anatol Pomozov 提交于 
      struct block_device lifecycle is defined by its inode (see fs/block_dev.c) -
block_device allocated first time we access /dev/loopXX and deallocated on
bdev_destroy_inode. When we create the device "losetup /dev/loopXX afile"
we want that block_device stay alive until we destroy the loop device
with "losetup -d".

But because we do not hold /dev/loopXX inode its counter goes 0, and
inode/bdev can be destroyed at any moment. Usually it happens at memory
pressure or when user drops inode cache (like in the test below). When later in
loop_clr_fd() we want to use bdev we have use-after-free error with following
stack:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000280
  bd_set_size+0x10/0xa0
  loop_clr_fd+0x1f8/0x420 [loop]
  lo_ioctl+0x200/0x7e0 [loop]
  lo_compat_ioctl+0x47/0xe0 [loop]
  compat_blkdev_ioctl+0x341/0x1290
  do_filp_open+0x42/0xa0
  compat_sys_ioctl+0xc1/0xf20
  do_sys_open+0x16e/0x1d0
  sysenter_dispatch+0x7/0x1a

To prevent use-after-free we need to grab the device in loop_set_fd()
and put it later in loop_clr_fd().

The issue is reprodusible on current Linus head and v3.3. Here is the test:

  dd if=/dev/zero of=loop.file bs=1M count=1
  while [ true ]; do
    losetup /dev/loop0 loop.file
    echo 2 > /proc/sys/vm/drop_caches
    losetup -d /dev/loop0
  done

[ Doing bdgrab/bput in loop_set_fd/loop_clr_fd is safe, because every
  time we call loop_set_fd() we check that loop_device->lo_state is
  Lo_unbound and set it to Lo_bound If somebody will try to set_fd again
  it will get EBUSY.  And if we try to loop_clr_fd() on unbound loop
  device we'll get ENXIO.

  loop_set_fd/loop_clr_fd (and any other loop ioctl) is called under
  loop_device->lo_ctl_mutex. ]
Signed-off-by: NAnatol Pomozov <anatol.pomozov@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      c1681bf8
    • L
      Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux · aae92db9
      由 Linus Torvalds 提交于 
      Pull tegra clock driver fix from Mike Turquette:
 "Missing base address in Tegra clock driver results in non-operational
  PCIe.  On some devices this means that Ethernet will go uninitialized
  and other devices will fail.  This pull request fixes it with a single
  patch to pass the proper base address in the Tegra clock driver."

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
  clk: tegra: Allow PLLE training to succeed
      aae92db9
    • L
      Merge tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe · dc543f9e
      由 Linus Torvalds 提交于 
      Pull FCoE fixes from Robert Love:
 "Critical patches to fix FCoE VN2VN mode with new interfaces targeting
  3.9-rc"

* tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe:
  libfcoe: Fix fcoe_sysfs VN2VN mode
  libfc, fcoe, bnx2fc: Split fc_disc_init into fc_disc_{init, config}
  libfc, fcoe, bnx2fc: Always use fcoe_disc_init for discovery layer initialization
  fcoe: Fix deadlock between create and destroy paths
  bnx2fc: Make the fcoe_cltr the SCSI host parent
      dc543f9e
    • T
      clk: tegra: Allow PLLE training to succeed · 0f1bc12e
      由 Thierry Reding 提交于 
      Under some circumstances the PLLE needs to be retrained, in which case
access to the PMC registers is required. Fix this by passing a pointer
to the PMC registers instead of NULL when registering the PLLE clock.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-By: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>
      0f1bc12e
  9. 01 4月, 2013 5 次提交
    • L
      Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile · 3658f360
      由 Linus Torvalds 提交于 
      Pull arch/tile fix from Chris Metcalf:
 "This change allows newer Tilera boot tools to work correctly with
  current (and stable) kernels by using the right filename to get the
  initramfs from the Tilera hypervisor filesystem."

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: expect new initramfs name from hypervisor file system
      3658f360
    • L
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · ff3421de
      由 Linus Torvalds 提交于 
      Pull networking fixes from David Miller:

 1) sadb_msg prepared for IPSEC userspace forgets to initialize the
    satype field, fix from Nicolas Dichtel.

 2) Fix mac80211 synchronization during station removal, from Johannes
    Berg.

 3) Fix IPSEC sequence number notifications when they wrap, from Steffen
    Klassert.

 4) Fix cfg80211 wdev tracing crashes when add_virtual_intf() returns an
    error pointer, from Johannes Berg.

 5) In mac80211, don't call into the channel context code with the
    interface list mutex held.  From Johannes Berg.

 6) In mac80211, if we don't actually associate, do not restart the STA
    timer, otherwise we can crash.  From Ben Greear.

 7) Missing dma_mapping_error() check in e1000, ixgb, and e1000e.  From
    Christoph Paasch.

 8) Fix sja1000 driver defines to not conflict with SH port, from Marc
    Kleine-Budde.

 9) Don't call il4965_rs_use_green with a NULL station, from Colin Ian
    King.

10) Suspend/Resume in the FEC driver fail because the buffer descriptors
    are not initialized at all the moments in which they should.  Fix
    from Frank Li.

11) cpsw and davinci_emac drivers both use the wrong interface to
    restart a stopped TX queue.  Use netif_wake_queue not
    netif_start_queue, the latter is for initialization/bringup not
    active management of the queue.  From Mugunthan V N.

12) Fix regression in rate calculations done by
    psched_ratecfg_precompute(), missing u64 type promotion.  From
    Sergey Popovich.

13) Fix length overflow in tg3 VPD parsing, from Kees Cook.

14) AOE driver fails to allocate enough headroom, resulting in crashes.
    Fix from Eric Dumazet.

15) RX overflow happens too quickly in sky2 driver because pause packet
    thresholds are not programmed correctly.  From Mirko Lindner.

16) Bonding driver manages arp_interval and miimon settings incorrectly,
    disabling one unintentionally disables both.  Fix from Nikolay
    Aleksandrov.

17) smsc75xx drivers don't program the RX mac properly for jumbo frames.
    Fix from Steve Glendinning.

18) Fix off-by-one in Codel packet scheduler.  From Vijay Subramanian.

19) Fix packet corruption in atl1c by disabling MSI support, from Hannes
    Frederic Sowa.

20) netdev_rx_handler_unregister() needs a synchronize_net() to fix
    crashes in bonding driver unload stress tests.  From Eric Dumazet.

21) rxlen field of ks8851 RX packet descriptors not interpreted
    correctly (it is 12 bits not 16 bits, so needs to be masked after
    shifting the 32-bit value down 16 bits).  Fix from Max Nekludov.

22) Fix missed RX/TX enable in sh_eth driver due to mishandling of link
    change indications.  From Sergei Shtylyov.

23) Fix crashes during spurious ECI interrupts in sh_eth driver, also
    from Sergei Shtylyov.

24) dm9000 driver initialization is done wrong for revision B devices
    with DSP PHY, from Joseph CHANG.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
  DM9000B: driver initialization upgrade
  sh_eth: make 'link' field of 'struct sh_eth_private' *int*
  sh_eth: workaround for spurious ECI interrupt
  sh_eth: fix handling of no LINK signal
  ks8851: Fix interpretation of rxlen field.
  net: add a synchronize_net() in netdev_rx_handler_unregister()
  MAINTAINERS: Update netxen_nic maintainers list
  atl1e: drop pci-msi support because of packet corruption
  net: fq_codel: Fix off-by-one error
  net: calxedaxgmac: Wake-on-LAN fixes
  net: calxedaxgmac: fix rx ring handling when OOM
  net: core: Remove redundant call to 'nf_reset' in 'dev_forward_skb'
  smsc75xx: fix jumbo frame support
  net: fix the use of this_cpu_ptr
  bonding: fix disabling of arp_interval and miimon
  ipv6: don't accept node local multicast traffic from the wire
  sky2: Threshold for Pause Packet is set wrong
  sky2: Receive Overflows not counted
  aoe: reserve enough headroom on skbs
  line up comment for ndo_bridge_getlink
  ...
      ff3421de
    • J
      DM9000B: driver initialization upgrade · 6741f40d
      由 Joseph CHANG 提交于 
      Fix bug for DM9000 revision B which contain a DSP PHY

DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().

Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.

Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: NJoseph CHANG <josright123@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6741f40d
    • S
      sh_eth: make 'link' field of 'struct sh_eth_private' *int* · 3340d2aa
      由 Sergei Shtylyov 提交于 
      The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the
'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and
the former field gets assigned from the latter. Make the field match, getting
rid of incorrectly used PHY_DOWN value in assignments/comparisons.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3340d2aa
    • S
      sh_eth: workaround for spurious ECI interrupt · 3893b273
      由 Sergei Shtylyov 提交于 
      At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!

The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).

While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NMax Filippov <max.filippov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3893b273