Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Removing unused code as FW does not need any value in mbox-5.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Issue:
While unloading driver MBOX 0x31 fail as DDB logout (MBOX 0x56)
operation is not completed.

Fix:
Wait for DDB Logout completion before MBOX 0x31
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Issue:
Driver holds rom-lock for too long during reset recovery.

During adapter reset testing, it was found that the driver
holds the rom-lock for too long, because of which other
drivers fail to acquire the rom-lock, leading to reset
failures.
The primary cause is, in the bootstrap code, while
holding the rom-lock, the driver checks if the peg is
halted, causing a 2 second contention.

Fix:
When a reset recovery starts, the driver deduces the cause, and
sets appropriate flags in watchdog & recover_adapter routines.
This flag should be used to determine if bootstrap is invoked
from probe or reset context, reducing the rom-lock footprint of
the drivers.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Issue:
minidump data collection fails as driver reports data mismatch

Fix:
When the driver encounters a new entry type that it cannot process,
it should just skip the entry and adjust the total buffer size by
subtracting the skipped bytes from it. This is to ensure that there
is no data mismatch because of the new entries.
Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Issue:
Pending IO wait does not complete after triggering Graceful reset,
causing ack timeout and call traces.

Fix:
1. Reducing the IO command wait timeout before triggering reset,
   as logically also timeout should be less than reset timeout (10sec).
2. Moving the abort IO after chip reset, because only after
   chip reset, driver owns the IO otherwise it is with firmware and can
   still revert back with response.
Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Issue:
While booting with kdump kernel, driver receive IOCB interrupts
for which it is not ready which results in processing them
before init_firmware during driver probe

Fix:
Two steps solution
1. Make driver ready to process the interrupt before interupts
   handlers is registered.
2. Stop driver processing iocb interrupts if not generated as per
   firmware protocol i.e R2H bit set
Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Issue:
Mailbox command 0x102 (IDC Time Extend) failure seen while applying
changes to iface using iscsiadm

Fix:
Added fix to extend IDC timeout only for ISP84xx when IDC ACK
needs to be posted and disable ACB mailbox command completion
is in intermediate state.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Issue:
qla4xxx Unable to clear DDB indices when logout fails due to
failure of connection close mbox command.

Root cause:
If login to session fail, iscsiadm make call to destroy_session.
qla4xxx driver does not free ddb index map before free_ddb()

Fix:
Clear DDB Index map before free_ddb in "destroy_session"
in case of connection close mailbox command failure with 4005h.
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If waiting for signals was interrupted then the device was put to
FAILED state. Use msleep instead of msleep_interruptible to handle
this correctly.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Removed AF_83XX_NO_FWDUMP flag and directly checking IDC_CTRL bit1
while taking minidump, to check for graceful reset.
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Issue:

For ISP8xxx, adapter initialization is not retried if
qla4xxx_initialize_adapter fails.

Fix:

If qla4xxx_initialize_adapter fails, first check if failure is due to IRQs not
attached in order to skip retrial, then free the IRQs and then retry
initializing the adapter.
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJohn Soni Jose <sony.john-n@emulex.com>
Signed-off-by: NJayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Setting DMA bit mask 64 and roll back to 32 if not supported.
Signed-off-by: NMinh Tran <minhduc.tran@emulex.com>
Signed-off-by: NJayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

scsi_cmnd n io_task was not NULL when
 - Link goes down while IO was happening and session is closed.
 - Task for which TMF was sent.
Signed-off-by: NJohn Soni Jose <sony.john-n@emulex.com>
Signed-off-by: NJayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In iSCSI Boot scenario, when machine is reboot/shutdown phase
the active sessions are not closed. Driver queue cleanup is
done as part of unload and device is disabled.

Sessions are still active, iSCSI commands are issued from
session which comes to driver, as driver cleanup and device
disabled there is kernel stack dump with errors.

Fix is invoking iscsi_session_failure with ISCSI_ERR_INVALID_HOST
on all the active sessions when shutdown routine is called.
Signed-off-by: NJohn Soni Jose <sony.john-n@emulex.com>
Signed-off-by: NJayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The doorbel format has been updated to support additonal functionalities
of SKH-R adapter. These changes are made such that older FW also works fine.
Signed-off-by: NJohn Soni Jose <sony.john-n@emulex.com>
Signed-off-by: NJayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The 100Mbps port speed macro used was not proper.
Signed-off-by: NJohn Soni Jose <sony.john-n@emulex.com>
Signed-off-by: NJayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When an MBX command timeout happens,the resources associated with
the MBX command were freed. If FW were to give the response to
host after the timeout value set by driver then driver crashes as the MBX Cmd
resources were already freed.

This patch fixes this issue by maintaing a state flag for each of
the MBX command posted/timedout/completed.
Signed-off-by: NJohn Soni Jose <sony.john-n@emulex.com>
Signed-off-by: NJayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

On encountering unexpected error conditions from driver initiated
commands, print something useful like CDB and sense data rather than
something useless like the kernel virtual address of the command buffer.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Do no rescan on every events -- way too many rescans are
triggered if we don't filter the events.  Limit rescans
to be triggered by the following set of events:

 * controller state change
 * enclosure hot plug
 * physical drive state change
 * logical drive state change
 * redundant controller state change
 * accelerated io enabled/disabled
 * accelerated io configuration change
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Don't wait for *all* commands to complete, only for accelerated mode
commands.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add controller-based data-at-rest encryption compatibility
to ioaccel2 path (HP SSD Smart Path).

Encryption feature requires driver to supply additional fields
for encryption enable, tweak index, and data encryption key index
in the ioaccel2 request structure.

Encryption enable flag and data encryption key index come from
raid_map data structure from raid offload command.

During ioaccel2 submission, check device structure's raid map to see if
encryption is enabled for the device. If so, call new function below.

Add function set_encrypt_ioaccel2 to set encryption flag, data encryption key
index, and calculate tweak value from request's logical block address.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Change the handling of HP SSD Smart Path errors with status:
  0x02 CHECK CONDITION
  0x08 BUSY
  0x18 RESERVATION CONFLICT
  0x40 TASK ABORTED
So that they get retried on the RAID Path.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Code was confused and assumed that page zero was not
VPD page and all non-zero pages were VPD pages.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Allow driver to schedule a rescan whenever a request fails on the ioaccel2 path.
This eliminates the possibility of driver getting stuck in non-ioaccel mode.

IOaccel mode (HP SSD Smart Path) is disabled by driver upon error detection.
Driver relied on idea that request would be retried through normal path, and a
subsequent error would occur on that path, and be processed by controller
firmware.  As part of that process, controller disables ioaccel mode and later
reinstates it, signalling driver to change modes.

In some error cases, the error will not duplicate on the standard path,
so the driver could get stuck in non-ioaccel mode.
To avoid that, we allow driver to request a rescan during the next run of the
rescan thread.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Allow SSD Smart Path for a controller to be disabled by
the user, regardless of settings in controller firmware
or array configuration.

To disable:     echo 0 > /sys/class/scsi_host/host<id>/acciopath_status
To re-enable:   echo 1 > /sys/class/scsi_host/host<id>/acciopath_status
To check state: cat /sys/class/scsi_host/host<id>/acciopath_status
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Load balance across members of a N-way mirror set, and
handle the meta-RAID levels: R10, R50, R60.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Otherwise we could wind up using incorrect raid map data, and
then very bad things would likely happen.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>