This is the driver for the IR transmitter diode found on the Nokia
N900 (also known as RX51) device. The driver is mostly the same as
found in the original 2.6.28 based kernel that comes with the device.

The following modifications have been made compared to the original
driver version:

- Adopt to the changes that has happen in the kernel during the past
  five years, such as the change in the include paths

- The OMAP DM-timers require much more care nowadays. The timers need
  to be enabled and disabled or otherwise many actions fail. Timers
  must not be freed without first stopping them or otherwise the timer
  cannot be requested again.

The code has been tested with sending IR codes with N900 device
running Debian userland. The device receiving the codes was Anysee
DVB-C USB receiver.
Signed-off-by: NTimo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This callback were meant to allow overriding a FE callback, before its
call, but it is not really needed, as the callback can be intercepted
after tuner attachment.

Worse than that, only DVBv3 calls are intercepted this way, so a DVBv5
application will produce different effects than a DVBv3 one.

So, get rid of it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.

In two cases, the original memory allocation function was kmalloc, which
has been changed to a zeroing allocation to benefit from the devm function.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is a proper ene0100 driver anyway.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This has been replaced by the ttusbir driver.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently write() will return 0 if an IR device does not support sending.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This simplies the code and resolves a possible race condition between
ir_raw_decode_timer_end() and saa7134_raw_decode_irq().

If the interrupt handler is called after ir_raw_decode_timer_end()
calls ir_raw_event_handle() but before clearing ir->active, then the
timer won't be rearmed.

Compile tested only.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The TechnoTrend USB IR Receiver sends 125 ISO URBs per second, even when
there is no IR activity. Reduce the number of wake ups from the other
drivers too.

This saves about 0.25ms/s on a 2.4GHz Core 2 according to powertop.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver adds support for TechnoTrend USB IR Receiver. It is a complete
rewrite of the staging/media/lirc/lirc_ttusbir driver. It adds more
accurate sample reporting and led control.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Pioneer CU-700 remote causes receiver overflows if you hold down any
button. The remote does not send NEC IR repeats, it repeats the entire
NEC code after 20ms.

The iguanair hardware advertises an interval of 10 which just not enough;
with 100 URBs per second and at most 7 edges per URB, we handle at most
700 edges per second. The remote generates about 900.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With the timeout supplied the interface can go idle. The keymap is
the same one as other drivers which do not come with a remote.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Also fix error codes returned from open.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now unbind also stops the receiver.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Firmware versions lower than 0x0205 use a different interface which is not
supported. Also report the firmware version in the standard format.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rather than using usb_interrupt_msg() to receive responses, reuse the
urb callback we already have in place.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After thinking twice, I ended up adding own value for AUTO
interleaving instead of using NONE.

API minor number is not needed to increase as that patch should
be the same Kernel as interleaving parameter is initially added.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: Andreas Oberritter <obi@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move rtl2831u LED from streaming control to power control. It
changes LED behavior slightly but who cares :)
After that same streaming control can be used for both rtl2831u
and rtl2832u.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The camera requires the PROBE_MINMAX quirk. Add a corresponding entry in
the device IDs list.
Reported-by: NStefan Muenzel <stefanmuenzel@googlemail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The SPCAM SP620U camera uses the alternate "Y8  " GUID for the 8-bit
greyscale format, and supports a 12-bit greyscale format. Add support
for those in the driver, as well as for 10-bit greyscale formats.
Signed-off-by: NStefan Muenzel <stefanmuenzel@googlemail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Compute the maximum number of bytes per interval using the burst and
multiplier values for super speed endpoints.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Support for yet another SAA7146-based budget card (very similar to TT
S2-1600, but use LNBH23 instead ISL6423).
Signed-off-by: NEvgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver has been replaced by stk1160.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver adds support for stk1160 usb bridge as used in some
video/audio usb capture devices.
It is a complete rewrite of staging/media/easycap driver and
it's meant as a replacement.

As stk1160 allows communication with an ac97 codec chip, this
driver allows to register a control-only sound card to allow the user
to access ac97 controls.

Two devices have been used for testing:
* 1-cvbs video and 1-audio ac97 input,
* 4-cvbs inputs
Both of these devices reports with the same id [05e1:0408],
so the driver tries to support a superset of the capabilities.

By using keep_buffers module parameter it's possible to prevent
the driver from releasing urb buffers when streaming is stopped.
The usage of this parameter can avoid memory fragmentation that may
cause the driver to stop working on low memory systems.
A similar mechanism is implemented in em28xx driver (see commit 86d38d).
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

qt1010_init_meas2() returns zero on success and negative error codes on
failure so the return type should be int instead of u8.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>