Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

PLL was not being enabled when it was not bypassed. This patch
enables the PLL when it is used. Additionally, it disables the PLL
when it is bypassed.

Without this patch, the audio on TI DM646x EVM and DM355 EVM
does not work properly. The bit clocks and the frame sync signals
from the codec are not correct and hence the playback/record are faster
than usual for most sample rates. The reason for this was that the PLL
was not enabled when it was not bypassed.

Tested on DM6467 EVM, playback tested on DM355 EVM.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The callback function to control register was used by whole controls in
MAX9877 driver, but this causes using many if statement for double
register control or invert.
So, the callback function for double register control is separate
differently, and the code for invert is added in the callback function.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reset was failing with the original udelay(50) between the code in
psc_ac97_cold_reset() and the call to psc_ac97_warm_reset(). Through testing
it was found that a delay of 1ms was necessary for the cold_reset code to
consistently complete successfully.
Signed-off-by: NJohn Bonesio <bones@secretlab.ca>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

GCC 4.4.0 doesn't appear to be able to spot that we don't apply any FLL
configuration if the output frequency is zero.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Board sdp3430 has hardware support for EXTMUTE using TWL4030 GPIO6
line, controlled by register INTBR_PMBR1. Machine driver takes care
of enabling gpio line through i2c and codec driver manipulates the
line during headset ramp up/down sequence.
Signed-off-by: NJorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Replaced with dev_{get|set}_drvdata().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NBarry Song <21cnbao@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

clock name strings are no longer passed on platform_data.  Instead,
we rely entirely on struct device and clkdev to find the right clock.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The MAX9877 combines a high-efficiency Class D audio power amplifier
with a stereo Class AB capacitor-less DirectDrive headphone amplifier.

The max9877_add_controls() is called to register the MAX9877 specific
controls on machine specific init() of the machine driver.

The datasheet for the MAX9877 can find at the following url:
http://datasheets.maxim-ic.com/en/ds/MAX9877.pdf

[Slight edit to sort the ALL_CODECS entries -- broonie.]
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is a macro for double controls with special callback function and
TLV. The SOC_DOUBLE_R_EXT_TLV needs two registers and one shift for
double controls.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is a macro for double controls with special callback function and
TLV. The SOC_DOUBLE_EXT_TLV needs one register and two shifts for double
controls.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Due to the flexibility of the WM9081 FLL this should never happen
in a real system.
Reported-by: NJaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We need to use the best value we picked, not the last value we
looked at.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no need to manually start playback/capture ourselves as the PCM
driver will handle things for us.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no need to manually start playback/capture ourselves as the PCM
driver will handle things for us.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Without MODULE_LICENCE("GPL"), when built as a module it will fail
to load because it uses other GPL symbols from kernel.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In SOC DAPM layer of SOUND subsystem, when add signal route (in the
function snd_soc_dapm_add_route() ), the original code has wrong logic
when dapm layer check each widget whether an external one.
Signed-off-by: NRongrong Cao <rrcao@ambarella.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Keep index within stac9766_reg[]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Check for rtd->params->drcmr != NULL before accessing it.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Provide an interval after the end of DAPM sequencing so that we
can distinguish between a pop in the final step of the sequence
and a pop generated from some other source outside DAPM.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The system clock is currently fixed by the driver and this avoids
the need for us to handle errors with enabling and disabling MCLK
(which was incorrect previously so this fixes bugs in error
handling).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

As shipped the board does not have inputs but it is relatively
straightforward to modify the board to hook them up so support
is provided in the driver. When these modifications have not
been made enabling the microphone stage can cause problems.

Add an ifdef to disable this by default. Don't put it into
Kconfig since users will have to get their soldering irons
out to change things.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This simplifies the driver by removing the need to manually
configure dividers within the CPU and improve audio performance
by ensuring that the optimal phase relationships between the
clocks in the system are maintained.

Note that currently this means that for playback to work the
Output Mixer HiFi switch must be enabled since otherwise CODEC
will not generate the DAC clock.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

While the hardware is capable of some limited asynmmetric modes the
driver does not currently support those modes so tell applications
that only symmetric rates are available.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8993 is a highly integrated ultra-low power hi-fi CODEC designed
for portable devices such as multimedia phones.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Update the dma link with correct data as soon as
the master channel has copied it. Otherwise, the
1st period will play twice.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Conflicts:
	sound/soc/davinci/davinci-i2s.c

Nothing uses it and the existing hw_read operation needs to be
refectored so it's easier to remove it rather than work with it.
Support can be re-added if the code requires volatile registers.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>