Most ARM machines don't need a special "DMA" memory zone, and
when configured out, the kernel becomes a bit smaller:

|   text    data     bss     dec     hex filename
|3826182  102384  111700 4040266  3da64a vmlinux
|3823593  101616  111700 4036909  3d992d vmlinux.nodmazone

This is because the system now has only one zone total which effect is
to optimize away many conditionals in page allocation paths.

So let's configure this zone only on machines that need split zones.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove the old led support in arch/arm/mach-pxa/leds...
for TRIZEPS4 SOM. It is / will be replaced by generic
led driver drivers/leds/...
Signed-off-by: NJürgen Schindele <linux@schindele.name>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Enable Sparsemem support for LH7A40x SoCs, while still allowing the
existing discontig support for the time being.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Tested on Assabet, and Assabet with Neponset's SDRAM at 3328M phys.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Orion-1-90 (88F6183) is another member of the Orion SoC family,
which has a 16 bit DDR2 interface, one x1 PCIe port (configurable as
Root Complex or Endpoint), one 10/100/1000 ethernet interface, one
USB 2.0 port with PHY, one SPDIF/I2S interface, one SDIO interface,
one TWSI interface, two UARTs, one SPI interface, a NAND controller,
a crypto engine, and a 4-channel DMA engine.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Switch DaVinci SOC gpios over to using the new GPIO library, so it can
access GPIO expanders and other non-SOC GPIOs using the same calls.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

HAVE_AOUT doesn't quite do the same thing as the recently removed
ARCH_SUPPORTS_AOUT config option. That was set even on platforms where
binfmt_aout isn't supported, although it's not entirely clear why.

So it's best just to introduce a new symbol, handled consistently with
other similar HAVE_xxx symbols; with a simple 'select' in the arch Kconfig.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We don't need this any more; arguably we never really did.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds a config option (CONFIG_VMSPLIT_*) to allow choosing
between 3:1, 2:2 and 1:3 user:kernel memory splits.
Tested-by: NRiku Voipio <riku.voipio@iki.fi>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add Oprofile kernel support for ARMv7.
Tested on OMAP3430 and OMAP3530 chipsets (Cortex-A8).
Signed-off-by: NJean Pihet <jpihet@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ordinarily, memory holes in flatmem still have a valid memmap and is safe
to use. However, an architecture (ARM) frees up the memmap backing memory
holes on the assumption it is never used. /proc/pagetypeinfo reads the
whole range of pages in a zone believing that the memmap is valid and that
pfn_valid will return false if it is not. On ARM, freeing the memmap breaks
the page->zone linkages even though pfn_valid() returns true and the kernel
can oops shortly afterwards due to accessing a bogus struct zone *.

This patch lets architectures say when FLATMEM can have holes in the
memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo
will confirm that the page linkages are still valid by checking page->zone
is still the expected zone. The lookup of page_zone is safe as there is a
limited range of memory that is accessed when calling page_zone.  Even if
page_zone happens to return the correct zone, the impact is that the counters
in /proc/pagetypeinfo are slightly off but fragmentation monitoring is
unlikely to be relevant on an embedded system.
Reported-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Tested-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds kernel build support for the regulator core.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NLiam Girdwood <lg@opensource.wolfsonmicro.com>

This fixes a merge goof whereby ARCH_EP93XX got the "select HAVE_CLK" line
which belongs instead with ARCH_AT91.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

7444a72e caused these platforms to lose
their GPIOLIB configuration.  Convert the missed Kconfig symbols using:

  sed -i s/HAVE_GPIO_LIB/ARCH_REQUIRE_GPIOLIB/ arch/arm/Kconfig arch/arm/plat-s3c24xx/Kconfig
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.

The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file.  This patch adds the implementations for
x86 and PPC.

With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions.  Support
for more architectures can easily be added.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they
support <linux/clk.h> calls, so that otherwise portable drivers which need
those calls can list that dependency.

Something like this is a prerequisite for merging the musb_hdrc driver,
currently used on platforms including Davinci, OMAP2430, OMAP3xx ...  and
the discrete TUSB6010 chip, which doesn't have a natural platform
dependency.  (Used with OMAP 2420 in current Nokia N8x0 tablets.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds the ARCH=arm specific a kgdb backend, originally
written by Deepak Saxena <dsaxena@plexity.net> and George Davis
<gdavis@mvista.com>.  Geoff Levand <geoffrey.levand@am.sony.com>,
Nicolas Pitre, Manish Lachwani, and Jason Wessel have contributed
various fixups here as well.

The KGDB patch makes one change to the core ARM architecture such that
the traps are initialized early for use with the debugger or other
subsystems.

[ mingo@elte.hu: small cleanups. ]
[ ben-linux@fluff.org: fixed early_trap_init ]
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NDeepak Saxena <dsaxena@plexity.net>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch brings support for gpio/gpiolib framework to Intel IOP3xx
platforms.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds timer support for the i.MX machine family. This code can
be used on the following machs:

 - i.MX1 (tested)
 - i.MX2 (i.MX21 (to be tested), i.MX27 (tested))
 - i.MX3 (i.MX31 (tested))

TODO: It seems impossible to build a kernel for more than one CPU because the
timer do not follow the platform device rules. So it does only work if
timer 1 can be accessed on all CPUs at the same address.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch bases on the one from Daniel Mack. The most important change to
Daniel's patch is to be more generic. This gpio routine supports at least
the i.MX27 and i.MX31 processors.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
Acked-by: NDaniel Mack <daniel@caiaq.de>

ARM architecture is not using __do_IRQ
Acked-By: NUwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use HAVE_PATA_PLATFORM for ARCH_RPC

Cc: Linux ARM Kernel <linux-arm-kernel@lists.arm.linux.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This converts arm to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single().

Fixups and testing done by Catalin Marinas <catalin.marinas@arm.com>

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The Marvell Discovery Duo (MV78xx0) is a family of ARM SoCs featuring
(depending on the model) one or two Feroceon CPU cores with 512K of L2
cache and VFP coprocessors running at (depending on the model) between
800 MHz and 1.2 GHz, and features a DDR2 controller, two PCIe
interfaces that can each run either in x4 or quad x1 mode, three USB
2.0 interfaces, two 3Gb/s SATA II interfaces, a SPI interface, two
TWSI interfaces, a crypto accelerator, IDMA/XOR engines, a SPI
interface, four UARTs, and depending on the model, two or four gigabit
ethernet interfaces.

This patch adds basic support for the platform, and allows booting
on the MV78x00 development board, with functional UARTs, SATA, PCIe,
GigE and USB ports.
Signed-off-by: NStanislav Samsonov <samsonov@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a
Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface,
a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS
interface, and IDMA/XOR engines, and depending on the model, also
features one or two Gigabit Ethernet interfaces, two SATA II
interfaces, one or two TWSI interfaces, one or two UARTs, a
TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and
an SDIO interface.

This patch adds supports for the Marvell DB-88F6281-BP Development
Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs,
enabling support for the PCIe interface, the USB interface, the
ethernet interfaces, the SATA interfaces, the TWSI interfaces, the
UARTs, and the NAND controller.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

The Marvell Loki (88RC8480) is an ARM SoC based on a Feroceon CPU
core running at between 400 MHz and 1.0 GHz, and features a 64 bit
DDR controller, 512K of internal SRAM, two x4 PCI-Express ports,
two Gigabit Ethernet ports, two 4x SAS/SATA controllers, two UARTs,
two TWSI controllers, and IDMA/XOR engines.

This patch adds support for the Marvell LB88RC8480 Development
Board, enabling the use of the PCIe interfaces, the ethernet
interfaces, the TWSI interfaces and the UARTs.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NRussell King <linux@arm.linux.org.uk>

Available for !SMP only at the moment.

From Russell:

|Basically, if a thread is running on a CPU, thread_saved_fp() is invalid.
|So, the question is: what guarantees do we have here that 'tsk' is not
|running on another CPU?
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Tested-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Core ftrace support for the ARM architecture, which includes support
for dynamic function tracing.
Signed-off-by: NAbhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

dyntick is superseded by the clocksource/clockevent infrastructure,
using the NO_HZ configuration option.  No one implements dyntick on
ARM anymore, so it's pointless keeping it around.  Remove dyntick
support.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Trying to compile a kerel for ARCH_CO285 fails with the following error:

<--  snip  -->

...
  CC      arch/arm/mach-footbridge/dc21285.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:
In function 'dc21285_base_address':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: 'PCICFG0_BASE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:57: error: 'PCICFG1_BASE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:
In function 'dc21285_scan_bus':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:286: error: implicit declaration of function 'pci_scan_bus'
...
make[2]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1

<--  snip  -->

This does not seem to be a recent breakage.

The ARCH_CO285 support is old - kernel 2.2.0 contains first traces of
it, an it seems to have been pretty complete in later 2.2 kernels.

Since it seems to be completely dead code now this patch therefore
removes it.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h

It turns out this was done for ARM, and we can simply always select 
HAVE_IDE on ARM instead of manually tracking which platforms might 
possible have an IDE controller directly or indirectly.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Source drivers/uio/Kconfig to make UIO available in menuconfig if ARCH=arm.
Signed-off-by: NHans J Koch <hjk@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds support for the generic GPIO lib to the EP93xx family. The gpio
handling code has been moved from core.c to a new file called gpio.c.
The GPIO based IRQ code has not been changed.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>