The settings of the new chip are the same with RTL8152, except that
its product ID is 0x8050.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Getting the device version out of the driver really aids debugging.
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stop queuing rx packets if it is more than 1000.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use PLA 0xe000 bit 8 to check if disabling ALDPS is finished.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move tp->rtl_ops.init() from rtl8152_resume() to rtl8152_reset_resume().
The initialization is only necessary for reset_resume().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only RTL8153 could set coalesce, so move the default setting for
rtl8152_probe() to r8153_init().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use another way to keep disabling the U2P3 for both RTL_VER_03 and
RTL_VER_04.

Move enabling U2P3 from r8153_init() to r8153_hw_phy_cfg(). The
engineer ask the setting should be done after PHY settings.

Disable U2P3 first in rtl8153_up().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust the order of rtl8153_runtime_enable() according to the
suggestion from the engineer.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the setting from r8153_first_init() to r8153_init(). It only needs to
be set once.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MAC clock speed down could be enabled if the U1/U2 is disabled.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable lpm after r8153_init() and remove other enable/disable lpm.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use r8153_phy_status() to check phy status of RTL8153.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make return value void since functions never returns meaningfull value.
Signed-off-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function is not used, removing it fixes the following warning when
building with clang:

drivers/net/usb/r8152.c:825:5: error: unused function 'usb_ocp_read'
    [-Werror,-Wunused-function]
Signed-off-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this the generic cdc_ether grabs the device,
and does not really work.
Signed-off-by: NRené Rebe <rene@exactcode.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The linking status may be changed when autosuspend. And, after
autoresume, the driver may try to transmit packets when the device
is carrier off, because the interrupt transfer doesn't update the
linking status, yet. And, if the device is in ALDPS mode, the device
would stop working.

The another similar case is
 1. unplug the cable.
 2. interrupt transfer queue a work_queue for linking change.
 3. device enters the ALDPS mode.
 4. a tx occurs before the work_queue is called.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

revert commit a59e6d81 ("r8152: correct the rx early size") and
fix the rx early size as

	(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check hw version first in probe(). Do nothing if the driver doesn't
support the chip.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The list rx_done would be initialized when the linking on occurs.
Therefore, if a napi is scheduled without any linking on before,
the following kernel panic would happen.

	BUG: unable to handle kernel NULL pointer dereference at 000000000000008
	IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152]
	PGD 0
	Oops: 0002 [#1] SMP
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace &tp->napi with napi and tp->netdev with netdev.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Acked-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Schedule the napi after napi_enable() for rx, if it is necessary.

If the rx is completed when napi is disabled, the sheduling of napi
would be lost. Then, no one handles the rx packet until next napi
is scheduled.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-schedule napi after napi_complete() for tx, if it is necessay.

In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.

After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace rumtime with runtime.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Runtime suspend shouldn't be executed if the tx queue is not empty,
because the device is not idle.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rtl8152_post_reset() should sumbit rx urb and interrupt transfer,
otherwise the rx wouldn't work and the linking change couldn't be
detected.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the hw rx checksum is always enabled, and the user couldn't switch
it to sw rx checksum.

Note that the RTL_VER_01 only support sw rx checksum only. Besides,
the hw rx checksum for RTL_VER_02 is disabled after
commit b9a321b4 ("r8152: Fix broken RX checksums."). Re-enable it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.

If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If usb_submit_urb() called from the open function fails, the following
crash may be observed.

r8152 8-1:1.0 eth0: intr_urb submit failed: -19
...
r8152 8-1:1.0 eth0: v1.08.3
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b6b7b
pgd = ffffffc0e7305000
[6b6b6b6b6b6b6b7b] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
...
PC is at notifier_chain_register+0x2c/0x58
LR is at blocking_notifier_chain_register+0x54/0x70
...
Call trace:
[<ffffffc0002407f8>] notifier_chain_register+0x2c/0x58
[<ffffffc000240bdc>] blocking_notifier_chain_register+0x54/0x70
[<ffffffc00026991c>] register_pm_notifier+0x24/0x2c
[<ffffffbffc183200>] rtl8152_open+0x3dc/0x3f8 [r8152]
[<ffffffc000808000>] __dev_open+0xac/0x104
[<ffffffc0008082f8>] __dev_change_flags+0xb0/0x148
[<ffffffc0008083c4>] dev_change_flags+0x34/0x70
[<ffffffc000818344>] do_setlink+0x2c8/0x888
[<ffffffc0008199d4>] rtnl_newlink+0x328/0x644
[<ffffffc000819e98>] rtnetlink_rcv_msg+0x1a8/0x1d4
[<ffffffc0008373c8>] netlink_rcv_skb+0x68/0xd0
[<ffffffc000817990>] rtnetlink_rcv+0x2c/0x3c
[<ffffffc000836d1c>] netlink_unicast+0x16c/0x234
[<ffffffc00083720c>] netlink_sendmsg+0x340/0x364
[<ffffffc0007e85d0>] sock_sendmsg+0x48/0x60
[<ffffffc0007e9c30>] SyS_sendto+0xe0/0x120
[<ffffffc0007e9cb0>] SyS_send+0x40/0x4c
[<ffffffc000203e34>] el0_svc_naked+0x24/0x28

Clean up error handling to avoid registering the notifier if the open
function is going to fail.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The r8152 driver has been broken since (approx) 3.16.xx
when support was added for hardware RX checksums
on newer chip versions.  Symptoms include random
segfaults and silent data corruption over NFS.

The hardware checksum logig does not work on the VER_02
dongles I have here when used with a slow embedded system CPU.
Google reveals others reporting similar issues on Raspberry Pi.

So, disable hardware RX checksum support for VER_02, and fix
an obvious coding error for IPV6 checksums in the same function.

Because this bug results in silent data corruption,
it is a good candidate for back-porting to -stable >= 3.16.xx.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usbnet:
- Remove stale new_mtu <= 0 check in usbnet.c
- Set min_mtu = 0, max_mtu = 65535 (sub-drivers must set their own
  max_mtu and/or min_mtu as needed)

r8152:
- Set appropriate max_mtu for different variants (1500 or 9194)

lan78xx:
- Set max_mtu = 9000

asix_driver:
- max_mtu = 16384 for ax88178 variant

ax88179:
- max_mtu = 4088

cdc_ncm:
- max_mtu from hardware

cdc-phonet:
- min_mtu = 6, max_mtu = 65541

sierra_net:
- max_mtu = 1500, call usbnet_change_mtu directly
- sierra_net_change_mtu checked for MTU > 1500, then called
  usbnet_change_mtu, but if we set max_mtu to let the network core handle
  the range check, then we can simply call usbnet_change_mtu directly

smsc75xx:
- max_mtu = 9000

CC: netdev@vger.kernel.org
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
CC: Hayes Wang <hayeswang@realtek.com>
CC: Oliver Neukum <oneukum@suse.com>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the following four products of Lenovo and sort the order of the list.

	VID		PID
	0x17ef		0x3062
	0x17ef		0x3069
	0x17ef		0x720c
	0x17ef		0x7214
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.

Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.

v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86

CC: netdev@vger.kernel.org
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable ALDPS and EEE to avoid the possible failure when setting the PHY.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove r8153_enable_eee().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>