We want to call iwl_mvm_inactivity_check() from here in the
next patch, so need to move the code down to be able to.

Fix a minor checkpatch complaint while at it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This function is only used in the file where it's declared,
so just make it static.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Instead of iterating all the queues after having potentially
changed some queue configurations, rechecking if that was done,
mark the ones that do need a TID change explicitly in a bitmap
and use that to send the change to the firmware.

While at it, also rename iwl_mvm_change_queue_owner() to
iwl_mvm_change_queue_tid() since that's more obvious - the
"kind" of owner isn't immediately clear right now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We set the queue to this state, only to pretty much immediately
move it out of it again. However, we can't even hit any of the
code that checks if the queue is reconfiguring, because all of
this happens under mvm->mutex and we hold the all the way from
marking the queue as RECONFIGURING to marking it as READY again.

Additionally, the queue that became RECONFIGURING would've been
in SHARED state before, and it can safely stay in that state. In
case of errors, it previously would have stayed in RECONFIGURING
which it could never have left again.

Remove the state entirely and just track the queues that need to
be reconfigured in a separate, local, bitmap.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We currently reconfigure the queues after the inactivity check,
but only in one of the two callers. This might leave queues in
a state where the TID owner is wrong, if called when reserving
a queue for a new station.

Clean this up and do the reconfiguration inside the inactivity
check function. This requires changing the locking, but one of
the two places already holds the mvm mutex and the other easily
can.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If TVQM is used we skip over this, move the code into a new
function to get rid of the label.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no need to build a bitmap first and then iterate,
just do the iteration with the right locking directly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no need to have a hw refcount if we just mark the
command queue with a (fake) TID; at that point, the refcount
becomes equivalent to the hweight() of the TID bitmap.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

None of these functions really need to be separate, they're all
only used in sta.c, move them there and make them static.

Fix a small typo in related code while at it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Make this a named struct rather than an anonymous one,
we'll want to refer to it by name later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move the rt status checking to the start of the resume flow in order
to avoid sending D0I3_END_CMD to the FW.  Also, collect dump if an
assert was encountered.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Debug data dump is not working in flows that stop the device is used
in their error handling. During these flows the op mode mutex is
locked until the device stops.  Because of that, any assert generated
from the firmware can be handled only after the device already
stopped.

Since dumping cannot occour after stopping the device, split the the
dump function to two parts, Part that handles locking, and the part
that starts the actual dumping and call the second part in the op mode
stop device function.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently in case of DCM with P2P GO where BSS DTIM interval < 220 msec
the fw fails to allocate events for the P2P GO dtim due to long passive
scan events.

Fix this by requesting all scans in this scenario to be fragmented with
fast balance scan time settings.  The only exception is in case
fragmented scan was planned to be set due to low latency or high
throughput reason, set the scan timing as planned.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fast balance scan is similar to SCAN_TYPE_MILD, but this scan is
fragmented and has shorter out of operating channel time,
and therefore better match low latency scenarios.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Split TX tracing to be per TB. This is needed now that
AMSDUs can be sent and skb can be larger than trace
limit.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we TX AMSDU, we shouldn't pad the packet. In the past,
we were building AMSDU only in transport layer, and gen2
functions are built based on this. However, now that op mode
may build AMSDUs, we need to take care of padding also in
gen2 "non-pcie-amsdu" path.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed.  Note that RSC is sent separately in
a new command.  This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

iwl_fw_dbg_collect can be called by any function that already
has the error string ready. iwl_fw_dbg_collect_trig, on the
other hand, does string formatting. The occurrences decrement
is at iwl_fw_dbg_collect_trig, instead of iwl_fw_dbg_collect,
which causes it to sometimes be skipped. Move it to the right
location.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NYisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As preparation for new trigger format, make the function
agnostic to the trigger fomat. Instead it gets the relevant
parameters - id and delay.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.

Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add debugfs to send host command in mvm and fmac op modes.
Allows to send host command at runtime via send_hcmd debugfs file.
The command is received as a string that represents hex values.

The struct of the command is as follows:
[cmd_id][flags][length][data]
cmd_id and flags are 8 chars long each.
length is 4 chars long.
data is length * 2 chars long.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Bump the firmware API version to 41.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If we use the iwl_pcie_txq_build_tfd() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The fall-through to the MVM case is intended as we have to do
*something* to continue, and can't easily clean up. So we'll
just fail in mvm later, if this does happen.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If we use the iwl_pcie_gen2_set_tb() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.

Fixes: ab6c6445 ("iwlwifi: pcie: copy TX functions to new transport")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

With NICs that don't read the NVM directly and instead rely on getting
the relevant data from the firmware, the number of reserved MAC
addresses was not added to the API. This caused the driver to assume
there is only one address which results in all interfaces getting the
same address. Update the API to fix this.

While at it, fix-up the comments with firmware api names to actually
match what we have in the firmware.

Fixes: e9e1ba3d ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: NNaftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Trigger dump collection if the alive flow fails, regardless of the
reason.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If all free RB queues are empty, the driver will never restock the
free RB queue.  That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.

Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).

There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.

But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).

To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In mac80211, the default remains for HT, so set the limit to
HE for our driver.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For SU/SU-ER/MU PPDUs we have spatial reuse.

For those where it's relevant we also know the pre-FEC
padding factor, PE disambiguity bit, beam change bit
and doppler bit.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add information about the LDCP extra symbol segment to the HE
data when applicable (not for trigger-based PPDUs).

While at it, clean up the code for UL/DL a bit.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We have this data available, so add it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This code gets shorter if it doesn't have to check all the
conditions, so move it to an appropriate place that has all
of them validated already.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Split the code out into a separate routine, and move that to be
called inside the previously introduced iwl_mvm_decode_he_phy_data()
function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Pull some of the decoding of he_phy_data into a separate function so
we don't need to check over and over again if it's valid.

While at it, fix the UL/DL bit reporting to be for all but trigger-
based frames.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>