These are aways called together, and my merging them we reduce the amount
of indirect calls, improve type safety and in general clean up the code
a bit.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Create a helper that encapsulates the whole logic to create a defer
intent.  This reorders some of the work that was done, but none of
that has an affect on the operation as only fields that don't directly
interact are affected.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Since no caller is using KM_NOSLEEP and no callee branches on KM_SLEEP,
we can remove KM_NOSLEEP and replace KM_SLEEP with 0.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

There are many, many xfs header files which are included but
unneeded (or included twice) in the xfs code, so remove them.

nb: xfs_linux.h includes about 9 headers for everyone, so those
explicit includes get removed by this.  I'm not sure what the
preference is, but if we wanted explicit includes everywhere,
a followup patch could remove those xfs_*.h includes from
xfs_linux.h and move them into the files that need them.
Or it could be left as-is.
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

During testing of xfs/141 on a V4 filesystem, I observed some
inconsistent behavior with regards to resources that are held (i.e.
remain locked) across a defer roll.  The transaction roll always gives
the defer roll function a new transaction, even if committing the old
transaction fails.  However, the defer roll function only rejoins the
held resources if the transaction commit succeedied.  This means that
callers of defer roll have to figure out whether the held resources are
attached to the transaction being passed back.

Worse yet, if the defer roll was part of a defer finish call, we have a
third possibility: the defer finish could pass back a dirty transaction
with dirty held resources and an error code.

The only sane way to handle all of these scenarios is to require that
the code that held the resource either cancel the transaction before
unlocking and releasing the resources, or use functions that detach
resources from a transaction properly (e.g.  xfs_trans_brelse) if they
need to drop the reference before committing or cancelling the
transaction.

In order to make this so, change the defer roll code to join held
resources to the new transaction unconditionally and fix all the bhold
callers to release the held buffers correctly.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>

There's no need to bundle a pointer to the defer op type into the defer
op control structure.  Instead, store the defer op type enum, which
enables us to shorten some of the lines.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>

Recently, we forgot to port a new defer op type to xfsprogs, which
caused us some userspace pain.  Reorganize the way we make libxfs
clients supply defer op type information so that all type information
has to be provided at build time instead of risky runtime dynamic
configuration.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>

struct xfs_defer_ops has now been reduced to a single list_head. The
external dfops mechanism is unused and thus everywhere a (permanent)
transaction is accessible the associated dfops structure is as well.

Remove the xfs_defer_ops structure and fold the list_head into the
transaction. Also remove the last remnant of external dfops in
xfs_trans_dup().
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The majority of remaining references to struct xfs_defer_ops in XFS
are associated with xfs_defer_add(). At this point, there are no
more external xfs_defer_ops users left. All instances of
xfs_defer_ops are embedded in the transaction, which means we can
safely pass the transaction down to the dfops add interface.

Update xfs_defer_add() to receive the transaction as a parameter.
Various subsystems implement wrappers to allocate and construct the
context specific data structures for the associated deferred
operation type. Update these to also carry the transaction down as
needed and clean up unused dfops parameters along the way.

This removes most of the remaining references to struct
xfs_defer_ops throughout the code and facilitates removal of the
structure.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
[darrick: fix unused variable warnings with ftrace disabled]
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The xfs_defer_ops ->dop_pending list is used to track active
deferred operations once intents are logged. These items must be
aborted in the event of an error. The list is populated as intents
are logged and items are removed as they complete (or are aborted).

Now that xfs_defer_finish() cancels on error, there is no need to
ever access ->dop_pending outside of xfs_defer_finish(). The list is
only ever populated after xfs_defer_finish() begins and is either
completed or cancelled before it returns.

Remove ->dop_pending from xfs_defer_ops and replace it with a local
list in the xfs_defer_finish() path. Pass the local list to the
various helpers now that it is not accessible via dfops. Note that
we have to check for NULL in the abort case as the final tx roll
occurs outside of the scope of the new local list (once the dfops
has completed and thus drained the list).
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The current semantics of xfs_defer_finish() require the caller to
call xfs_defer_cancel() on error. This is slightly inconsistent with
transaction commit error handling where a failed commit cleans up
the transaction before returning.

More significantly, the only requirement for exposure of
->dop_pending outside of xfs_defer_finish() is so that
xfs_defer_cancel() can drain it on error. Since the only recourse of
xfs_defer_finish() errors is cancellation, mirror the transaction
logic and cancel remaining dfops before returning from
xfs_defer_finish() with an error.

Beside simplifying xfs_defer_finish() semantics, this ensures that
xfs_defer_finish() always returns with an empty ->dop_pending and
thus facilitates removal of the list from xfs_defer_ops.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The dfops code still passes around the xfs_defer_ops pointer
superfluously in a few places. Clean this up wherever the
transaction will suffice.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The dfops infrastructure ->finish_item() callback passes the
transaction and dfops as separate parameters. Since dfops is always
part of a transaction, the latter parameter is no longer necessary.
Remove it from the various callbacks.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Inodes that are held across deferred operations are explicitly
joined to the dfops structure to ensure appropriate relogging.
While inodes are currently joined explicitly, we can detect the
conditions that require relogging at dfops finish time by inspecting
the transaction item list for inodes with ili_lock_flags == 0.

Replace the xfs_defer_ijoin() infrastructure with such detection and
automatic relogging of held inodes. This eliminates the need for the
per-dfops inode list, replaced by an on-stack variant in
xfs_defer_trans_roll().
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Buffers that are held across deferred operations are explicitly
joined to the dfops structure to ensure appropriate relogging.
While buffers are currently joined explicitly, we can detect the
conditions that require relogging at dfops finish time by inspecting
the transaction item list for held buffers.

Replace the xfs_defer_bjoin() infrastructure with such detection and
automatic relogging of held buffers. This eliminates the need for
the per-dfops buffer list, replaced by an on-stack variant in
xfs_defer_trans_roll().
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The dop_low field enables the low free space allocation mode when a
previous allocation has detected difficulty allocating blocks. It
has historically been part of the xfs_defer_ops structure, which
means if enabled, it remains enabled across a set of transactions
until the deferred operations have completed and the dfops is reset.

Now that the dfops is embedded in the transaction, we can save a bit
more space by using a transaction flag rather than a standalone
boolean. Drop the ->dop_low field and replace it with a transaction
flag that is set at the same points, carried across rolling
transactions and cleared on completion of deferred operations. This
essentially emulates the behavior of ->dop_low and so should not
change behavior.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

All callers pass ->t_dfops of the associated transactions. Refactor
the helpers to receive the transactions and facilitate further
cleanups between xfs_defer_ops and xfs_trans.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

With no more external dfops users, there is no need for an
xfs_defer_ops cancel wrapper.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Once xfs_defer_finish() has completed all deferred operations, it
checks the dirty state of the transaction and rolls it once more to
return a clean transaction for the caller. This primarily to cover
the case where repeated xfs_defer_finish() calls are made in a loop
and we need to make sure that the caller starts the next iteration
with a clean transaction. Otherwise we risk transaction reservation
overrun.

This final transaction roll is not required in the transaction
commit path, however, because the transaction is immediately
committed and freed after dfops completion. Refactor the final roll
into a separate helper such that we can avoid it in the transaction
commit path.  Lift the dfops reset as well so dfops remains valid
until after the last call to xfs_defer_trans_roll(). The reset is
also unnecessary in the transaction commit path because the
transaction is about to complete.

This eliminates unnecessary regrants of transactions where the
associated transaction roll can be replaced by a transaction commit.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NBill O'Donnell <billodo@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Every caller of xfs_defer_finish() now passes the transaction and
its associated ->t_dfops. The xfs_defer_ops parameter is therefore
no longer necessary and can be removed.

Since most xfs_defer_finish() callers also have to consider
xfs_defer_cancel() on error, update the latter to also receive the
transaction for consistency. The log recovery code contains an
outlier case that cancels a dfops directly without an available
transaction. Retain an internal wrapper to support this outlier case
for the time being.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NBill O'Donnell <billodo@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The dfops structure used by multi-transaction operations is
typically stored on the stack and carried around by the associated
transaction. The lifecycle of dfops does not quite match that of the
transaction, but they are tightly related in that the former depends
on the latter.

The relationship of these objects is tight enough that we can avoid
the cumbersome boilerplate code required in most cases to manage
them separately by just embedding an xfs_defer_ops in the
transaction itself. This means that a transaction allocation returns
with an initialized dfops, a transaction commit finishes pending
deferred items before the tx commit, a transaction cancel cancels
the dfops before the transaction and a transaction dup operation
transfers the current dfops state to the new transaction.

The dup operation is slightly complicated by the fact that we can no
longer just copy a dfops pointer from the old transaction to the new
transaction. This is solved through a dfops move helper that
transfers the pending items and other dfops state across the
transactions. This also requires that transaction rolling code
always refer to the transaction for the current dfops reference.

Finally, to facilitate incremental conversion to the internal dfops
and continue to support the current external dfops mode of
operation, create the new ->t_dfops_internal field with a layer of
indirection. On allocation, ->t_dfops points to the internal dfops.
This state is overridden by callers who re-init a local dfops on the
transaction. Once ->t_dfops is overridden, the external dfops
reference is maintained as the transaction rolls.

This patch adds the fundamental ability to support an internal
dfops. All codepaths that perform deferred processing continue to
override the internal dfops until they are converted over in
subsequent patches.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NBill O'Donnell <billodo@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

xfs_defer_init() is currently used in two particular situations. The
first and most obvious case is raw initialization of an
xfs_defer_ops struct. The other case is partial reinit of
xfs_defer_ops on reuse due to iteration.

Most instances of the first case will be replaced by a single init
of a dfops embedded in the transaction. Init calls are still
technically required for the second case because the dfops may have
low space mode enabled or have joined items that need to be reset
before the dfops should be reused.

Since the current dfops usage expects either a final transaction
commit after xfs_defer_finish() or xfs_defer_init() if dfops is to
be reused, we can shift some of the init logic into
xfs_defer_finish() such that the latter returns with a reinitialized
dfops. This eliminates the second dependency noted above such that a
dfops is immediately ready for reuse after an xfs_defer_finish()
without the need to change any calling code.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBill O'Donnell <billodo@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

dop_committed is set when deferred item processing rolls the
transaction at least once, but is only ever accessed in tracepoints.
The transaction roll/commit events are already available via
independent tracepoints, so remove the otherwise unused field.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBill O'Donnell <billodo@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

xfs_defer_finish() has a couple quirks that are not safe with
respect to the upcoming internal dfops functionality. First,
xfs_defer_finish() attaches the passed in dfops structure to
->t_dfops and caches and restores the original value. Second, it
continues to use the initial dfops reference before and after the
transaction roll.

These behaviors assume that dop is an independent memory allocation
from the transaction itself, which may not always be true once
transactions begin to use an embedded dfops structure. In the latter
model, dfops processing creates a new xfs_defer_ops structure with
each transaction and the associated state is migrated across to the
new transaction.

Fix up xfs_defer_finish() to handle the possibility of the current
dfops changing after a transaction roll. Since ->t_dfops is used
unconditionally in this path, it is no longer necessary to
attach/restore ->t_dfops and pass it explicitly down to
xfs_defer_trans_roll(). Update dop in the latter function and the
caller to ensure that it always refers to the current dfops
structure.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBill O'Donnell <billodo@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The following assertion was seen on generic/051:

XFS: Assertion failed: tp->t_firstblock == NULLFSBLOCK, file: fs/xfs/libxfs5
------------[ cut here ]------------
kernel BUG at fs/xfs/xfs_message.c:102!
invalid opcode: 0000 [#1] SMP PTI
CPU: 2 PID: 20757 Comm: fsstress Not tainted 4.18.0-rc4+ #3969
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.1-1 04/01/4
RIP: 0010:assfail+0x23/0x30
Code: c3 66 0f 1f 44 00 00 48 89 f1 41 89 d0 48 c7 c6 88 e0 8c 82 48 89 fa
RSP: 0018:ffff88012dc43c08 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff88012dc43ca0 RCX: 0000000000000000
RDX: 00000000ffffffc0 RSI: 000000000000000a RDI: ffffffff828480eb
RBP: ffff88012aa92758 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: f000000000000000 R12: 0000000000000000
R13: ffff88012dc43d48 R14: ffff88013092e7e8 R15: 0000000000000014
FS:  00007f8d689b8e80(0000) GS:ffff88013fd00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8d689c7000 CR3: 000000012ba6a000 CR4: 00000000000006e0
Call Trace:
 xfs_defer_init+0xff/0x160
 xfs_reflink_remap_extent+0x31b/0xa00
 xfs_reflink_remap_blocks+0xec/0x4a0
 xfs_reflink_remap_range+0x3a1/0x650
 xfs_file_dedupe_range+0x39/0x50
 vfs_dedupe_file_range+0x218/0x260
 do_vfs_ioctl+0x262/0x6a0
 ? __se_sys_newfstat+0x3c/0x60
 ksys_ioctl+0x35/0x60
 __x64_sys_ioctl+0x11/0x20
 do_syscall_64+0x4b/0x190
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The root cause of the assertion failure is that xfs_defer_finish doesn't
roll the transaction after processing all the deferred items.  Therefore
it returns a dirty transaction to the caller, which leaves the caller at
risk of exceeding the transaction reservation if it logs more items.

Brian Foster's patchset to move the defer_ops firstblock into the
transaction requires t_firstblock == NULLFSBLOCK upon defer_ops
initialization, which is how this was noticed at all.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>

All but one caller of xfs_defer_init() passes in the ->t_firstblock
of the associated transaction. The one outlier is
xlog_recover_process_intents(), which simply passes a dummy value
because a valid pointer is required. This firstblock variable can
simply be removed.

At this point we could remove the xfs_defer_init() firstblock
parameter and initialize ->t_firstblock directly. Even that is not
necessary, however, because ->t_firstblock is automatically
reinitialized in the new transaction on a transaction roll. Since
xfs_defer_init() should never occur more than once on a particular
transaction (since the corresponding finish will roll it), replace
the reinit from xfs_defer_init() with an assert that verifies the
transaction has a NULLFSBLOCK firstblock.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Most callers of xfs_defer_init() immediately attach the dfops
structure to a transaction. Add a transaction parameter to eliminate
much of this boilerplate code. This also helps self-document the
fact that many codepaths now expect a dfops pointer implicitly via
xfs_trans->t_dfops.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The ->t_agfl_dfops field is currently used to defer agfl block frees
from associated transaction contexts. While all known problematic
contexts have already been updated to use ->t_agfl_dfops, the
broader goal is defer agfl frees from all callers that already use a
deferred operations structure. Further, the transaction field
facilitates a good amount of code clean up where the transaction and
dfops have historically been passed down through the stack
separately.

Rename the field to something more generic to prepare to use it as
such throughout XFS. This patch does not change behavior.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Remove the verbose license text from XFS files and replace them
with SPDX tags. This does not change the license of any of the code,
merely refers to the common, up-to-date license files in LICENSES/

This change was mostly scripted. fs/xfs/Makefile and
fs/xfs/libxfs/xfs_fs.h were modified by hand, the rest were detected
and modified by the following command:

for f in `git grep -l "GNU General" fs/xfs/` ; do
	echo $f
	cat $f | awk -f hdr.awk > $f.new
	mv -f $f.new $f
done

And the hdr.awk script that did the modification (including
detecting the difference between GPL-2.0 and GPL-2.0+ licenses)
is as follows:

$ cat hdr.awk
BEGIN {
	hdr = 1.0
	tag = "GPL-2.0"
	str = ""
}

/^ \* This program is free software/ {
	hdr = 2.0;
	next
}

/any later version./ {
	tag = "GPL-2.0+"
	next
}

/^ \*\// {
	if (hdr > 0.0) {
		print "// SPDX-License-Identifier: " tag
		print str
		print $0
		str=""
		hdr = 0.0
		next
	}
	print $0
	next
}

/^ \* / {
	if (hdr > 1.0)
		next
	if (hdr > 0.0) {
		if (str != "")
			str = str "\n"
		str = str $0
		next
	}
	print $0
	next
}

/^ \*/ {
	if (hdr > 0.0)
		next
	print $0
	next
}

// {
	if (hdr > 0.0) {
		if (str != "")
			str = str "\n"
		str = str $0
		next
	}
	print $0
}

END { }
$
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

So it's clear in the trace where they are being called from.
Signed-Off-By: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Now that AGFL block frees are deferred when dfops is set in the
transaction, start deferring AGFL block frees from contexts that are
known to push the limits of existing log reservations.

The first such context is deferred operation processing itself. This
primarily targets deferred extent frees (such as file extents and
inode chunks), but in doing so covers all allocation operations that
occur in deferred operation processing context.

Update xfs_defer_finish() to set and reset ->t_agfl_dfops across the
processing sequence. This means that any AGFL block frees due to
allocation events result in the addition of new EFIs to the dfops
rather than being processed immediately. xfs_defer_finish() rolls
the transaction at least once more to process the frees of the AGFL
blocks back to the allocation btrees and returns once the AGFL is
rectified.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

In certain cases, defer_ops callers will lock a buffer and want to hold
the lock across transaction rolls.  Similar to ijoined inodes, we want
to dirty & join the buffer with each transaction roll in defer_finish so
that afterwards the caller still owns the buffer lock and we haven't
inadvertently pinned the log.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>

And instead require callers to explicitly join the inode using
xfs_defer_ijoin.  Also consolidate the defer error handling in
a few places using a goto label.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Split xfs_trans_roll into a low-level helper that just rolls the
actual transaction and a new higher level xfs_trans_roll_inode
that takes care of logging and rejoining the inode.  This gets
rid of the NULL inode case, and allows to simplify the special
cases in the deferred operation code.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

If the deferred ops transaction roll fails, we need to abort the intent
items if we haven't already logged a done item for it, regardless of
whether or not the deferred ops has had a transaction committed.  Dave
found this while running generic/388.

Move the tracepoint to make it easier to track object lifetimes.
Reported-by: NDave Chinner <david@fromorbit.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

When xfs_defer_finish calls ->finish_item, it's possible that
(refcount) won't be able to finish all the work in a single
transaction.  When this happens, the ->finish_item handler should
shorten the log done item's list count, update the work item to
reflect where work should continue, and return -EAGAIN so that
defer_finish knows to retain the pending item on the pending list,
roll the transaction, and restart processing where we left off.

Plumb in the code and document how this mechanism is supposed to work.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Christoph reports slab corruption when a deferred refcount update
aborts during _defer_finish().  The cause of this was broken log item
state tracking in xfs_defer_pending -- upon an abort,
_defer_trans_abort() will call abort_intent on all intent items,
including the ones that have already had a done item attached.

This is incorrect because each intent item has 2 refcount: the first
is released when the intent item is committed to the log; and the
second is released when the _done_ item is committed to the log, or
by the intent creator if there is no done item.  In other words, once
we log the done item, responsibility for releasing the intent item's
second refcount is transferred to the done item and /must not/ be
performed by anything else.

The dfp_committed flag should have been tracking whether or not we had
a done item so that _defer_trans_abort could decide if it needs to
abort the intent item, but due to a thinko this was not the case.  Rip
it out and track the done item directly so that we do the right thing
w.r.t. intent item freeing.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reported-by: NChristoph Hellwig <hch@infradead.org>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Add tracepoints for the internals of the deferred ops mechanism
and tracepoint classes for clients of the dops, to make debugging
easier.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

All the code around struct xfs_bmap_free basically implements a
deferred operation framework through which we can roll transactions
(to unlock buffers and avoid violating lock order rules) while
managing all the necessary log redo items.  Previously we only used
this code to free extents after some sort of mapping operation, but
with the advent of rmap and reflink, we suddenly need to do more than
that.

With that in mind, xfs_bmap_free really becomes a deferred ops control
structure.  Rename the structure and move the deferred ops into their
own file to avoid further bloating of the bmap code.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>