Some bad interaction between the idle and the suspend paths has been
identified: the idle code is called during the suspend enter and exit
sequences. This could cause corruption or lock-up of resources.

The solution is to move the calls to disable_hlt at the very beginning
of the suspend sequence (ex. in omap3_pm_begin instead of
omap3_pm_prepare), and the call to enable_hlt at the very end of
the suspend sequence (ex. in omap3_pm_end instead of omap3_pm_finish).

Tested with RET and OFF on Beagle and OMAP3EVM.
Signed-off-by: NJean Pihet <j-pihet@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can
be shared. Therefore board-stamp9g20.c is refactored to allow reusing the
SoM initialization and board-pcontrol-g20.c is modified to use it.
Signed-off-by: NChristian Glindkamp <christian.glindkamp@taskit.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The uhpck clock should be divided from the utmi clock, not its parent
(main). This change is mostly cosmetic as the uhpck rate value is not
used anywhere except for the debugfs clock output.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Fix interrupt priority level handling on SH-Mobile ARM.

SH-Mobile ARM platforms using multiple interrupt priority
levels need this patch to fix a potential dead lock that
may occur if multiple interrupts with different levels
are pending simultaneously.

The default INTC configuration is to use the same priority
level for all interrupts, so this issue does not trigger by
default. It is however common for board code to override the
interrupt priority for certain interrupt sources depending
on the application. Without this fix such boards may lock up.

In detail, this patch updates the INTC code in entry-macro.S
to make sure that the INTLVLA register gets set as expected.

To trigger this bug modify the board specific code to adjust
the interrupt priority level for the ethernet chip. After
changing the priority level simply use flood ping to drown
the board with interrupts.

This patch applies to INTCA-based processors such as sh7372,
sh7377 and sh7372. GIC-based processors are not affected.

Suitable for v2.6.37-rc and stable from v2.6.34 to v2.6.36.

Cc: stable@kernel.org
Signed-off-by: NMagnus Damm <damm@opensource.se>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Turn down the warning noise from the compiler,
basically a SH-Mobile specific version of the
patch located in the RMK patch tracker:

6484/1: "fix compile warning in mm/init.c",

Without this patch the following warning triggers:

 CC      arch/arm/kernel/sys_arm.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
  CC      arch/arm/kernel/traps.o
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds new entries required by the new version of MAX8998
driver. Without them, the driver fails to init. See commit 50f19a45Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

S3C2416 PM code uses low-level sleep routines from S3C2412 code,
but these routines are compiled only for S3C2412 SoC.

Split S3C2412_PM to two parts: S3C2412_PM, S3C2412_PM_SLEEP and
select last in S3C2416's Kconfig.
Signed-off-by: NYauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Should be CONFIG_S3C_DEV_NAND instead of CONFIG_S3C_DEVICE_NAND.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Cache ownership must be acquired by reading/writing data from the
cache line to make cache operation have the desired effect on the
SMP MPCore CPU. However, the ownership is never acquired in the
v6_dma_inv_range function when cleaning the first line and
flushing the last one, in case the address is not aligned
to D_CACHE_LINE_SIZE boundary.
Fix this by reading/writing data if needed, before performing
cache operations.
While at it, fix v6_dma_flush_range to prevent RWFO outside
the buffer.

Cc: stable@kernel.org
Signed-off-by: NValentine Barshak <vbarshak@mvista.com>
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Because the nwfpe support is unlikely to be used on new platforms
and requires CONFIG_OABI_COMPAT, which is not generally used with
ARMv7+, we shouldn't expect to build nwfpe support into a Thumb-2
kernel.

At present, nwfpe contains assembly code which isn't Thumb-2
compatible, and for now it doesn't appear useful to port this
code.

All ARMv7-A/R platforms necessarily have VFPv3 hardware floating-
point natively, making emulation unnecessary.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes sense, because Thumb-2 code can't execute on plain
ARMv6 processors.

This will avoid accidentally configuring a broken kernel where the
config otherwise would allow multiple architecture versions to
coexist in the same kernel.

Not adding !CPU_V5 etc., because the chance of anyone trying to
put v5 and v7 in the same kernel is low, and I'm not aware of
any mach which can do this.  These could be added later if it
matters.

Note that the rules may need to be refined if support for the
ARM1156J(F)-S processor is later added to the kernel, since this
processor supports the rare ARMv6T2 extensions, which add support
for Thumb-2 and a few other ARMv7 features.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current implementation of the v7_coherent_*_range function assumes
that the D and I cache lines have the same size, which is incorrect
architecturally. This patch adds the icache_line_size macro which reads
the CTR register. The main loop in v7_coherent_*_range is split in two
independent loops or the D and I caches. This also has the performance
advantage that the DSB is moved outside the main loop.
Reported-by: NKevin Sapp <ksapp@quicinc.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current implementation of the dcache_line_size macro reads the L1
cache size from the CCSIDR register. This, however, is not guaranteed to
be the smallest cache line in the cache hierarchy. The patch changes to
the macro to use the more architecturally correct CTR register.
Reported-by: NKevin Sapp <ksapp@quicinc.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

After Charu's GPIO hwmod patches, GPIO initialization on N800 emits
the following messages for all GPIO banks:

omap_hwmod: gpio1: cannot be enabled (3)

This is due to OMAP24XX_ST_GPIOS_SHIFT being defined as a bitmask.
Fix this and also fix two other macros that had the same problem.

Thanks to Tony Lindgren <tony@atomide.com> for originally reporting
this bug.

Signed-off-by: Paul Walmsley <paul@pwsan.com
Cc: Charulatha Varadarajan <charu@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit 0d8e2d0d (OMAP2+: PM/serial:
hold console semaphore while OMAP UARTs are disabled) added use of the
console semaphore to protect UARTs from being accessed after disabled
during idle, but this causes problems in suspend.

During suspend, the console semaphore is acquired by the console
suspend method (console_suspend()) so the try_acquire_console_sem()
will always fail and suspend will be aborted.

To fix, introduce a check so the console semaphore is only attempted
during idle, and not during suspend.  Also use the same check so that
the console semaphore is not prematurely released during resume.

Thanks to Paul Walmsley for suggesting adding the same check during
resume.

Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: NJean Pihet <j-pihet@ti.com>
Tested-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Kernel was failing to boot on omap1611 based OSK boards due to
mis-configured SRAM size.  Existing code was using a hard-coded value
for 250k, which was then rounded down by PAGE_SIZE.  Increasing this to
256k allows kernel to boot on omap1611 SoCs.

Problem reported by and initial fix suggested by Tim Bird.

Thanks to Tony Lindgren for helping diagnose the problem to being
specific to OMAP1611 and not affecting OMAP1610/OMAP1623.
Reported-by: NTim Bird <tim.bird@am.sony.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

clk_get() return value should be checked with IS_ERR().
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently the {set,get}_pull callbacks of the s3c24xx_gpiocfg_default structure
are initalized via s3c_gpio_{get,set}pull_1up. This results in a linker
error when only CONFIG_CPU_S3C2442 is selected:

arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f4): undefined reference to
`s3c_gpio_getpull_1up'
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f8): undefined reference to
`s3c_gpio_setpull_1up'

The s3c2442 has pulldowns instead of pullups compared to the s3c2440.
The method of controlling them is the same though.
So this patch modifies the existing s3c_gpio_{get,set}pull_1up helper functions
to take an additional parameter deciding whether the pin has a pullup or pulldown.
The s3c_gpio_{get,set}pull_1{down,up} functions then wrap that functions passing
either S3C_GPIO_PULL_UP or S3C_GPIO_PULL_DOWN.

Furthermore this patch sets up the s3c24xx_gpiocfg_default.{get,set}_pull fields
in the s3c244{0,2}_map_io function to the new pulldown helper functions.

Based on patch from "Lars-Peter Clausen" <lars@metafoo.de>
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Commit 0ea12930 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.

Fix that.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

clk_get() returns ERR_PTR() on error, not NULL.
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated to include err.h to compile on omap1]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch complements ed919b01 "mmc: sdio: fix runtime PM anomalies by
introducing MMC_CAP_POWER_OFF_CARD" by declaring MMC_CAP_POWER_OFF_CARD
on the ZOOM's wl1271 mmc slot.

This is required in order not to break runtime PM support for the wl1271
sdio driver.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

gic_set_cpu will directly use irq_desc[]. If CONFIG_SPARSE_IRQ is
enabled, there is no irq_desc[]. So we need use irq_to_desc(irq) to
get the descriptor for irq.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The existing code invokes the syscall with rubbish in r7,
due to what looks like an incorrect literal load idiom.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The MACH_MINI2440 entry requires the backlight LED driver, but this
subsystem has not been enabled and the select of LEDS_TRIGGER_BACKLIGHT
alone is insufficient to enable the necessary bits of the LED driver.

Add NEW_LEDS, LEDS_CLASS and LEDS_TRIGGER to the select to allow the
kernel to link.

This fixes the following error:

drivers/built-in.o: In function `led_trigger_set':
/home/ben/linux.git/drivers/leds/led-triggers.c:116: undefined reference to `led_brightness_set'
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Wakeup-on-timer code does not have/need debugfs dependency.  Move
the function out of debugfs ifdef.

Fixes compile error when CONFIG_DEBUG_FS is disabled but PM debug is
enabled.
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

to be a few more concistant with the other boards

as ek is for evaluation kit and dk for development kit
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>

Convert the following AT91RM9200-based boards to the new-style UART
initialization:
  - Ajeco 1ARM Single Board Computer
  - Sperry-Sun KAFA board
  - picotux 200

Remove the deprecated at91_init_serial
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>

Currently, the kprobes implementation for ARM only supports the ARM
instruction set, so it only works if CONFIG_THUMB2_KERNEL is not
enabled.

Until kprobes is updated to work with Thumb-2, turning it on will
cause horrible things to happen, so this patch disables it for now.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C.  If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.

In general, the following rules should be applied when using
data word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned data
words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume that
fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned, this
can cause impaired performance and stray alignment faults in some
circumstances.

In general, the following rules should be applied when using data word
declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The 32-bit conditional branches in Thumb-2 have a shorter range
(+/-512K) than their ARM counterparts (+/-32MB).  The linker does
not currently generate trampolines to extend the range of these
Thumb-2 conditional branches, resulting in link errors when vmlinux
is sufficiently large, e.g.:

head.o:(.text+0x464): relocation truncated to fit: R_ARM_THM_JUMP19

This patch forces the longer-range, unconditional branch encoding
by use of an explicit IT instruction.  The resulting branches are
triggered on the same conditions as before.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The code which makes up the zImage header intends to leave a
32-byte gap followed by a branch to the real entry point, a magic
number, and a word containing the absolute entry point address.

This gets messed up with with CONFIG_THUMB2_KERNEL, because the
size of the initial padding NOPs changes.

Instead, the header can be made fully compatible by restoring it to
ARM.

In the Thumb-2 case, we can replace the initial NOPs with a
sequence which switches to Thumb and jumps to the real entry point.

As a consequence, the zImage entry point is now always ARM, so no
special magic is needed any more for the uImage rules in the
Thumb-2 case.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some instruction operand combinations are used here which are nor
permitted in Thumb-2.

In particular, most uses of pc as an operand are disallowed in
Thumb-2, and deprecated in ARM from ARMv7 onwards.

The modified code introduced by this patch should be compatible
with all architecture versions >= v3, with or without
CONFIG_THUMB2_KERNEL.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.

In general, the following rules should be applied when using data
word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.

In this specific case, we can achieve the desired alignment by
forcing a 32-bit branch instruction using the W() macro, since the
assembler location counter is already 32-bit aligned in this case.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>