This patch adds checking for allocated DVMA memory and granted IRQ line.
Signed-off-by: NCyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In this driver, the default ethernet address is first set by by calling
eth_port_uc_addr_get() which reads the relevant registers of the
corresponding port as initially set by firmware. However that function
used the port_num field accessed through the private area of net_dev
before it was set.

The result was that one board I have ended up with the unicast address
set to 00:00:00:00:00:00 (only port 1 is connected on this board). The
problem appeared after commit 84dd619e.

This patch fixes the bug by setting mp->port_num prior to calling
eth_port_uc_get_addr().
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The tx timeout routine was waking the tx queue conditionally. However,
it must call it unconditionally since the dev_watchdog has halted the tx
queue before calling the timeout function.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The nic poll routine was missing the call to the optimized irq routine.
This patch adds the missing call for the optimized path.

See http://bugzilla.kernel.org/show_bug.cgi?id=7950 for more information.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixed rx checksum bits. Turn on TCP processing for rx checksum.
Fixed max frame length register write.  It wasn't getting set
in multi-port system. Set rx buffer queue length properly
for jumbo frames.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update the rx queue pointer when exiting NAPI poll rather than
at the end of each iteration.  Remove unnecessary PCI flushes
that occurred after every write.  Now write all regs and
flush once.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The proper header length was not being used.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This was removed in a previous patch to increase performance, but
caused a transmit error for the 4032 chip.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The original vendor driver contained a private ether_crc_le() function
that produced an inverted crc.  When we changed to the kernel version of
ether_crc_le(), we neglected to undo the inversion.  Let's do it now.
Discovered by and patch proffered by Jose Alberto Reguero.
Signed-off-by: NJose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Correctly detect when TSO should be used on transmit by looking at the
skb->gso_size rather than seeing if the frame was larger than our MTU.
The old method causes problems when a host with a large (jumbo) MTU is
sending to a host with a small (standard) MTU.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The user can generate console output if they cause do_mmap() to fail
during sys_io_setup().  This was seen in a regression test that does
exactly that by spinning calling mmap() until it gets -ENOMEM before
calling io_setup().

We don't need this printk at all, just remove it.
Signed-off-by: NZach Brown <zach.brown@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] gdth: fix oops in gdth_copy_cmd()
  [SCSI] mptsas: Fix oops for insmod during kexec
  [SCSI] lpfc: avoid double-free during PCI error failure

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (5472): Isl6421: don't reference freed memory
  V4L/DVB (5441): Saa7146: Fix allocation of clipping memory
  V4L/DVB (5421): Fix suspend/resume in msp3400 and tuner
  V4L/DVB (5415): Msp_attach must return 0 if no msp3400 was found.
  V4L/DVB (5408): Fix SECAM handling on saa7115
  V4L/DVB (5400): Core: fix several locking related problems
  V4L/DVB (5390): Radio: Fix error in Kbuild file
  V4L/DVB (5332): Ir_rc5_timer_end decoder lockup fix

* git://kvm.qumranet.com/home/avi/kvm:
  KVM: always reload segment selectors
  KVM: Prevent system selectors leaking into guest on real->protected mode transition on vmx

This reverts commit 94985134 and
insteads removes the WARN_ON() that caused that commit in the first
place.

The problem is that we call disable_nonboot_cpus() in swsusp before
powering down the system in order to avoid triggering the WARN_ON()
in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping() and this doesn't
work well on Thomas' system.

So instead, remove the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:
init_low_mapping(), which triggers every time during the suspend to disk
in the platform mode, as the potential problem it is related to doesn't
seem to occur in practice.

[ I think we might want to disallow the case of multiple users of that
  mm, or something.  Normally, playing with the current process page
  tables on the current CPU should be fine as long as we don't have
  other threads using those tables at the same time..

  Anyway, not pretty, but better than the warning or the lockup - Linus ]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The clockevents / tick management code expects an error value, when the
event is already expired. hpet_next_event() returns 1 in that case.

Fix it to return the proper -ETIME error code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
  Export __splice_from_pipe()
  2/2 splice: dont readpage
  1/2 splice: dont steal
  make elv_register() output atomic
  block: blk_max_pfn is somtimes wrong

Without attached patch against current -git I get following with
!PROC_SYSCTL (with EMBEDDED and PROC_FS set):

    CC      init/version.o
    LD      init/built-in.o
    LD      vmlinux
  fs/built-in.o: In function `do_proc_sys_lookup':
  proc_sysctl.c:(.text+0x26583): undefined reference to `sysctl_head_next'
  fs/built-in.o: In function `proc_sys_revalidate':
  proc_sysctl.c:(.text+0x265bb): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_readdir':
  proc_sysctl.c:(.text+0x26720): undefined reference to `sysctl_head_next'
  proc_sysctl.c:(.text+0x267d8): undefined reference to `sysctl_head_finish'
  proc_sysctl.c:(.text+0x268e7): undefined reference to `sysctl_head_next'
  proc_sysctl.c:(.text+0x26910): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_write':
  proc_sysctl.c:(.text+0x2695d): undefined reference to `sysctl_perm'
  proc_sysctl.c:(.text+0x2699c): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_read':
  proc_sysctl.c:(.text+0x269e9): undefined reference to `sysctl_perm'
  proc_sysctl.c:(.text+0x26a25): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_permission':
  proc_sysctl.c:(.text+0x26ad1): undefined reference to `sysctl_perm'
  proc_sysctl.c:(.text+0x26adb): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_lookup':
  proc_sysctl.c:(.text+0x26b39): undefined reference to `sysctl_head_finish'
  make: *** [vmlinux] Virhe 1

All those functions are in fs/proc/proc_sysctl.c, which has no CONFIG_
#define's in it, so the patch makes the compilation of that file to depend
on CONFIG_PROC_SYSCTL (the simplest choice).
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Because i don't have much time lately and my responses are pretty slow
it's probably best to remove me from MAINTAINERS to give someone else
the chance to jump in.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When CONFIG_IPC_NS=n, clone(CLONE_NEWIPC) claims success, but did not actually
clone a new IPC namespace.

Fix this to return -EINVAL so the caller knows his request was denied.
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I2O subsystem has been broken in mainstream several months ago (after
2.6.18).  Commit 4aff5e23 from Jens
Axboe split struct request ->flags into two parts: cmd_type and
cmd_flags.

In i2o layer this patch has replaced flag REQ_SPECIAL by the according
cmd_type.  However i2o has used REQ_SPECIAL not as command type but as
driver-specific flag for the debug purposes.  As result all i2o requests
have type "special" now, are not processed to the hardware and fail with
I/O error:

   i2o/hda:<3>Buffer I/O error on device i2o/hda, logical block 0
  Buffer I/O error on device i2o/hda, logical block 0
  Buffer I/O error on device i2o/hda, logical block 0
   unable to read partition table
  block-osm: device added (TID: 207): i2o/hda

The following patch removes the extra debug checks without any drawbacks and
restores the normal driver's work.
Signed-off-by: NVasily Averin <vvs@sw.ru>
Acked-by: NMarkus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  drivers/pcmcia/au1000_generic.c: In function 'au1x00_pcmcia_socket_probe':
  drivers/pcmcia/au1000_generic.c:375: error: 'struct device' has no member named 'dev'
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:eisa_root_register from .text between 'pci_eisa_init' (at offset 0xabf670) and 'virtual_eisa_release'

AFAIK a PCI to EISA bridge isn't anything hotpluggable, so
pci_eisa_init() can become __init.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I've been seeing some odd NTP behavior recently on a few boxes and
finally narrowed it down to time_offset overflowing when converted to
SHIFT_UPDATE units (which was a side effect from my HZfreeNTP patch).

This patch converts time_offset from a long to a s64 which resolves the
issue.

[tglx@linutronix.de: signedness fixes]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch uses MAX_REG_NR consistently to refer to the register file size.
 FRAME_SIZE isn't sufficient because on x86_64, it is smaller than the
ptrace register file size.  MAX_REG_NR was introduced as a consistent way
to get the number of registers, but wasn't used everywhere it should be.

When this causes a problem, it makes PTRACE_SETREGS fail on x86_64 because
of a corrupted segment register value in the known-good register file.  The
patch also adds a register dump at that point in case there are any future
problems here.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During a static link, ld has started putting a .note section in the
.uml.setup.init section.  This has the result that the UML setups begin
with 32 bytes of garbage and UML crashes immediately on boot.

This patch creates a specific .note section for ld to drop this stuff
into.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_register_master from .text between 'spi_bitbang_start' (at offset 0x84e11a) and 'bitbang_work'
  WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_alloc_master from .text between 'butterfly_attach' (at offset 0x84e681) and 'at25_remove'
  WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_new_device from .text between 'butterfly_attach' (at offset 0x84e7e4) and 'at25_remove'
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When CONFIG_UTS_NS=n, clone(CLONE_NEWUTS) quietly refuses.  So correctly does
not unshare a new uts namespace, but also does not return -EINVAL.

Fix this to return -EINVAL so the caller knows his request was denied.
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Its now used.. because we added the new definitions so enabled all the
goodies on i386
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

UML/x86_64 needs the same packing of struct epoll_event as x86_64.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

isar_bh() bh handler calls another (compatible) bh handler - BChannel_bh()
- but passes struct BCState* instead of struct work_struct*, which seems
wrong.

Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On Bob's machine clocksource is selecting PIT over the ACPI PM timer,
because he has the PIIX4 bug.  That bug drops the ACPI PM timers rating
to the same as the PIT, so that's why you're getting the PIT.

Realistically, the PIT is much slower then even the triple read ACPI PM,
so the de-ranking code is probably dropping it too far.

So don't drop ACPI PM quite so low if we see the PIIX4 bug.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Bob Tracy <rct@gherkin.frus.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit d720bc4b partially removed a
private implementation of baud speed decoding.  However it doesn't seem
to be complete: after the speed is decoded, it is still being used as an
index to a local speed table (array overrun, no doubt).

This was found by Graham Murray who noticed it caused a 2.6.19 regression
with the SX driver: https://bugs.gentoo.org/170554Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

...  still not sure why we need this ....
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If this mddev and queue got reused for another array that doesn't register a
congested_fn, this function would get called incorretly.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

All that is missing the the function pointers in raid4_pers.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This cancel_delayed_work call is called from a function that is only called
from a piece of code that immediate follows a cancel and destruction of the
workqueue, so it's clearly a mistake.

Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: N"J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The reused clientid here is a more of a problem for the client than the
server, and the client can report the problem itself if it's serious.
Signed-off-by: N"J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A regression introduced in the last set of acl patches removed the
INHERIT_ONLY flag from aces derived from the posix acl.  Fix.
Signed-off-by: N"J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

->readdir passes lofft_t offsets (used as nfs cookies) to
nfs3svc_encode_entry{,_plus}, but when they pass it on to encode_entry it
becomes an 'off_t', which isn't good.

So filesystems that returned 64bit offsets would lose.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>