The original code in omap2_clk_wait_ready() used to check the low 8
bits to determine whether they were within the FCLKEN or ICLKEN
registers.  Specifically, the test is satisfied when these offsets
are used:

 CM_FCLKEN, CM_FCLKEN1, CM_CLKEN, OMAP24XX_CM_FCLKEN2, CM_ICLKEN,
 CM_ICLKEN1, CM_ICLKEN2, CM_ICLKEN3, OMAP24XX_CM_ICLKEN4
 OMAP3430_CM_CLKEN_PLL, OMAP3430ES2_CM_CLKEN2

If one of these offsets isn't used, omap2_clk_wait_ready() merely
returns without doing anything.  So we should use the non-wait clkops
version instead and eliminate that conditional.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than employing run-time tests in omap2_clk_wait_ready() to
decide whether we need to wait for the clock to become ready, we
can set the .ops appropriately.

This change deals with the OMAP24xx and OMAP34xx conditionals only.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

PARENT_CONTROLS_CLOCK just makes enable/disable no-op, and is
functionally an alias for ALWAYS_ENABLED.  This can be handled
in the same way, using clkops_null.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

... and use it for clocks which are ALWAYS_ENABLED.  These clocks
use a non-NULL enable_reg pointer for other purposes (such as
selecting clock rates.)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Collect up all the common enable/disable clock operation functions
into a separate operations structure.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Nothing tests the clock flags for this bit, so it serves no purpose.
Remove it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

"flash" is a very generic name for a platform_driver that is only
available on SA11x0.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

SPIN_LOCK_UNLOCKED is deprecated as lockdep cannot properly work with
locks initialized with it.

This fix is necessary to compile the linux-rt tree for ARM.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Steven Rostedt <srostedt@redhat.com>

In omap24xx_cpu_suspend assembly routine, the r2 register which holds
the address of the SDRC_POWER reg is set to zero before the value is
written back triggering a fault due to writing to address zero.

It's hard to tell where this change was introduced since this file
has been moved and merged.

While this fix prevents a crash, suspend on my n810 is broken with
current kernels.  I never come out of suspend.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

By Ingo Molnar, interrupts are not masked by default.
(refer to 76d21601)

But if interrupts are not masked, the processor can wake up while in
Suspend-to-RAM state by an external interrupt. For example, if an
OMAP3 board is connected to Host PC by USB and entered to Suspend-to-RAM
state, it wake up automatically by M_IRQ_92. The disable_irq() function
can't disable the interrupt in H/W level, So I modified
arch/arm/mach-omap2/irq.c
Signed-off-by: NKim Kyuwon <chammoru@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When 32 kHz timer is used the min_delta_ns should be initialized so
that it reflects the timer programming cost. A write to the timer
device will be usually posted, but it takes roughly 3 cycles before
it is effective. If the timer is reprogrammed before that, the CPU
will stall until the previous write completes. This was pointed out by
Richard Woodruff.

Since the lower bound for min_delta_ns is 1000, the change is visible
only with tick rates less than 3 MHz.

Also note that the old value is incorrect for 32 kHz also due to
a rounding error, and it can cause the timer queue to hang (due to
clockevent code trying to program the timer with zero ticks).
Signed-off-by: NAaro Koskinen <Aaro.Koskinen@nokia.com>
Reviewed-by: NRichard Woodruff <r-woodruff2@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The naming accidentally broke while changing the name for the
driver to not to conflict with the other mmc driver.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix omap34xx revision detection for ES3.1
Signed-off-by: NTony Lindgren <tony@atomide.com>

This has similar symptoms than 66c23551
where just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch
can cause incorrect dump_stack(). Here it can happen if channel has been
used before and the channel flags variable holds old status.
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

CSR must be cleared before invoking the callback.

If the callback function starts a new, fast DMA transfer on the same
channel, the completion status might lost if CSR is cleared after
the callback invocation.
Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.

omap_mcbsp_request()
\- clk_enable(mcbsp->clk)         [takes and holds clockfw_lock]
    \- omap2_clk_enable()
       \- _omap2_clk_enable()
           \- omap_mcbsp_clk_enable()
              \- clk_enable(child clock)   [tries for clockfw_lock again]

mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.

The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When there are multiple L1-aliasing userland mappings of the same physical
page, we currently remap each of them uncached, to prevent VIVT cache
aliasing issues. (E.g. writes to one of the mappings not being immediately
visible via another mapping.)  However, when we do this remapping, there
could still be stale data in the L2 cache, and an uncached mapping might
bypass L2 and go straight to RAM.  This would cause reads from such
mappings to see old data (until the dirty L2 line is eventually evicted.)

This issue is solved by forcing a L2 cache flush whenever the shared page
is made L1 uncacheable.

Ideally, we would make L1 uncacheable and L2 cacheable as L2 is PIPT. But
Feroceon does not support that combination, and the TEX=5 C=0 B=0 encoding
for XSc3 doesn't appear to work in practice.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Aaro says:
> With spinlock debugs enabled I get might_sleep() warnings when using
> ptrace.

tracked down to a missing enable_irq before calling do_undefinstr().
Reported-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Tested-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-msm/board-halibut.c:45: error: implicit declaration of function 'MSM_GPIO_TO_INT'
arch/arm/mach-msm/board-halibut.c:45: error: initializer element is not constant
arch/arm/mach-msm/board-halibut.c:45: error: (near initialization for 'smc91x_resources[1].start')
arch/arm/mach-msm/board-halibut.c:46: error: initializer element is not constant
arch/arm/mach-msm/board-halibut.c:46: error: (near initialization for 'smc91x_resources[1].end')
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.

This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: NGerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE.  Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE.  Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system.  Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.

Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should.  Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Remove some leftover cruft from the arch/ppc days
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The 5329 ColdFire peripheral IO register addresses are not relative to
the MBAR register. So fix the serial platform setup array and IRQ acking
to use just the direct addresses.
Signed-off-by: NMatt Waddel <Matt.Waddel@freescale.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Make restart blocks working, required for proper syscall restarting.
Derived from same changes for m68k arch by Andreas Schwab <schwab@suse.de>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Greg Ungerer said about this board:
Only ever a handful where made, and that was in 1999.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

m68knommu does not set the Kconfig NO_DMA variable, but also does
not provide the required functions, resulting in the following
build error triggered by commit a40c24a1
(net: Add SKB DMA mapping helper functions.):

<--  snip  -->

..
  LD      vmlinux
net/built-in.o: In function `skb_dma_unmap':
(.text+0xac5e): undefined reference to `dma_unmap_single'
net/built-in.o: In function `skb_dma_unmap':
(.text+0xac7a): undefined reference to `dma_unmap_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xacdc): undefined reference to `dma_map_single'
net/built-in.o: In function `skb_dma_map':
(.text+0xace8): undefined reference to `dma_mapping_error'
net/built-in.o: In function `skb_dma_map':
(.text+0xad10): undefined reference to `dma_map_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xad82): undefined reference to `dma_unmap_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xadc6): undefined reference to `dma_unmap_single'
make[1]: *** [vmlinux] Error 1

<--  snip  -->
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Fix cache flushing for the 527x ColdFire processors
Its CACR register format is slightly different.

Along with this add support for flushing the 523x cache, which uses
the same format as the 527x ColdFire's, and was missing flush support.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Part of the code that did not make sense to me got removed by Greg.
This is part two:

The first compare is to check whether the interrupts are disabled or not.
Depending on the result we exectute the RESTORE_ALL macro is not only
restoring the stack but also returning to caller.
The test for pending softirq has been removed because it is allready done
in irq_exit().
Since system_call() is allso using the SAVE_ALL macro and returning via
ret_from_exception label I see no reason why we could not do this here
as well. This is also handy because if we return from the timer interrupt
and we need to resched than we check for this :)
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Probe the new mdio node added by b31a1d8b.  Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>