Add the MCP79 support to hda driver.
The patch base on kernel 2.6.23-rc7
Signed-off-by: NPeer Chen <peerchen@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Reading the signature of CS8427 over SPI/I2C fails on some devices
by mysterious reason.  In most cases, however, it succeeds at the
sequential read.  So, let's give a second chance to check the signature
again.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added the missing support for ASUS A7J [0x1043 0x1243]
Signed-off-by: NKailang Yang <kailang@realtek.com.tw>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

* Fixed ALC662 init verbs (wrong NIDs)
* Fixed ALC662 auto model issue (wrong DAC index)
Signed-off-by: NKailang Yang <kailang@realtek.com.tw>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The polling loop to check for ACI to go down was more convoluted than it
needed to be.  New loop should be more efficient and it is a lot simpler.  The
old loop checked for a timeout before checking for ACI down, which could
result in an erroneous timeout.  It's only a failure if the timeout expires
_and_ ACI is still high.  There is nothing wrong with the timeout expiring
while the task is sleeping if ACI went low.
A polling loop to check for the device to leaving INIT mode is removed.  The
device must have already left init for the previous ACI loop to have finished.
Acked-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Simplest fix.
Acked-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

These patches enable a few YMF743 controls (Tone/3D/IEC958) that won't
be detected with the current version of ALSA.
The second one contains following changes:
- A chip-specific SPDIF support for YMF743 (It doesn't have AC97
 standard SPDIF registers seen on YMF753).
- The implementation for 'IEC958 Playback Source' and 'IEC958 Mute'
 are identical to the ones for YMF753. But there is no 'IEC958 Output
 Pin' for YMF743.
Signed-off-by: NKeita Maehara <maehara@debian.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

These patches enable some YMF743 controls (Tone/3D/IEC958) that won't
be detected with the current version of ALSA.
The first one contains only cosmetic changes to share a few
YMF753-specific symbols with YMF743.
Signed-off-by: NKeita Maehara <maehara@debian.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Replace schedule_timeout() with schedule_timeout_uninterruptible()
to avoid signals in loop.
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Fix schedule_timeout() use in alsa-kernel. Mostly just
	schedule_timeout(1) --> schedule_timeout_uninterruptible(1)
The wavefront_synth one fixes the surrounding loop as well. In ymfpci_main,
delete a superfluous set_current_state() and in soc/soc-dapm.c replace an
_interruptible with _uninterruptible in some debug code; it's not waiting
for signals.

Signed-off-by: Rene Herman <rene.herman>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

More laptop BIOS changes the subsystem id for STAC9205 cards if the
microphone is toggled on/off in the settings.
The patch removes the old STAC_9205_M43xx and use STAC_9205_DELL_M43.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added the description about power-saving mode on AC97 and HD-audio drivers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added CONFIG_SND_AC97_POWER_SAVE_DEFAULT and CONFIG_SND_HDA_POWER_SAVE_DEFAULT
Kconfig options as the default values for power-saving mode of AC97 and
HD-audio drivers, respectively.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds support for audio part of the Ensoniq
SoundScape VIVO cards. The MIDI part is not supported.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The OPTi ISA-PnP chips advertise their OPL4 base at 0x380 (to 0x3f0) through
pnp and put their on-chip OPL3 at +8. The driver assumes the provided
value is the ALBase (OPL3 address) though and checks for an OPL4 at -8,
which means that simply adding 8 to the pnp provides value works to fix
detection of both OPL3 and OPL4.
Problem spotted on 931 and 933 by Krzysztof Helt and confirmed on 924 and
925 (together all OPTi ISA-PnP chips) by me.
Signed-off-by; Rene Herman <rene.herman@gmail.com>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Add descriptions for new module options of snd-sscape driver,
wss_port and dma2.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds second DMA channel and WSS port settings
to the sscape driver. Also, it adds internal card type setting.
The Ensoniq SoundScape VIVO PnP id is added but not handled
yet.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds support for Native Instrument's upcoming
RigKontrol3 sound interface.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch zeroes buffer for the card name and
fixes incorrect jump in the probe function.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch fixes MPU-401 irq values list in documentation.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Routines for effect processor FX8010: Use list_for_each_entry instead
of list_for_each
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Intel HD Audio: Use list_for_each_entry(_safe) instead of
list_for_each(_safe)
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

ESS Maestro 1/2/2E Sound Card: Use list_for_each_entry instead of
list_for_each
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch fixes ad1848_lib waiting loops to be the same as in the cs4231_lib.
Acked-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

sound/isa/sc6000.c: In function 'sc6000_dsp_reset':
sound/isa/sc6000.c:270: error: implicit declaration of function 'udelay'        sound/isa/sc6000.c: In function 'sc6000_init_mss':
sound/isa/sc6000.c:327: error: implicit declaration of function 'msleep'
{standard input}: Assembler messages:
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds a barrier() to prevent the compiler from
moving the read outside of the loop. It also fixes a comment.
Signed-off-by: NGiuliano Pochini <pochini@shiny.it>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds support for the Asus M2A-VM HDMI and Abit IP35-PRO
motherboards.
Signed-off-by: NTobin Davis <tdavis@dsl-only.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

I had a request for a 4 channel mode.  This should implement front
and surround outputs, leaving the 3rd plug for mic input.
Signed-off-by: NTobin Davis <tdavis@dsl-only.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

When playing multichannel data, the rear channels can get distorted if
the last sample of the last played stereo stream was not zero.  To avoid
this, add a hack to play a few silence samples after the stream is
stopped.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Remove some unused field from the struct cmipci_pcm, and change the type
of some others to save some space.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

When using one of the double sampling rates, use half the sample rate to
look up in the rates[] table, otherwise we stumble over the BUG().
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

By reorganizing the code that sets the CHB3DxC bits we can not only
simplify this code but also fix the bug where the CHB3D8C bit was not
reset when playing a stereo stream after a 7.1 stream.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Disallow playback of five channels because the hardware does not support
it (or nobody knows how to do it).
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Move the code that enables 96 kHz out of the if() that checks for
availability of both DMA channels so that it is enabled even when
another stream is playing on the front channels.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Initialize the registers at 0x90 and 0x91 with some undocumented values.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

When the chip is initialized, reset it.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Show a dump of all registers in the 0x00-0x27 and 0x90-0x93 ranges in
the 'cmipci' proc file.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Update comments for many register symbols, add some new register
symbols, and rename a few ones.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Use the proper value for the bit that identifies chip version 37.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Add an 'unknown' board type so that it is possible to differentiate
between unknown and generic boards.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>