The Virtual Functions should not be aware their function number.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.

2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
   IB or Ethernet.
   The driver will use this hint in case the user didn't specify explicitly the link layer
   type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
   and default the port to link sensing
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Added module parameters sr_iov and probe_vf for controlling enablement of
   SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
   SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
   ports configured as desired.
   In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
   for the case where the FW supports both port types (ETH and IB), the
   port_type_array parameter is used.
   By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
   to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
   mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
   modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
   VFs obtain their startup information from the PF (master) device via the
   comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
   aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership:  Currently, only one PF is supported by the driver.
   If the HCA is burned with FW which enables more than one PF, only one
   of the PFs is allowed to run.  The first one up grabs a FW ownership
   semaphone -- all other PFs will find that semaphore taken, and the
   driver will not allow them to run.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NLiran Liss <liranl@mellanox.co.il>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following commands are added here:
1. QUERY_FUNC_CAP and its wrapper.  This function is used by VFs when
   they start up to receive configuration information from the PF, such
   as resource quotas for this VF, which ports should be used (currently
   two), what protocol is running on the port (currently Ethernet ONLY,
   or port not active).

2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly
   by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now
   required here (the VF's MAC address must be substituted for the PFs
   MAC address returned by the FW). We changed the invocation
   in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper.

3. QUERY_HCA. Used by the VF to determine how the HCA was initialized.
   For now, we need only the multicast table member entry size
   (log2_mc_table_entry_sz, in the ConnectX PRM).  No wrapper is needed
   here, because the data may be passed as is to the VF without modification).

   In this command, we have added a GLOBAL_CAPS field for passing required
   configuration information from FW to a VF (this field is to allow safely
                   adding new SRIOV capabilities which require support in VF drivers, too).
   Bits will set here by FW in response to PF-driver configuration commands which
   will activate as yet undefined new SRIOV features. The VF will test to see that
   all required capabilities indicated by this field are supported (i.e., if a bit
   is set and the VF driver does not recognize that bit, it must abort
   its initialization).  Currently, no bits are set.

4. Added a CLOSE_PORT wrapper.  The PF context needs to keep track of how many VF contexts
   have the port open.  The PF context will not actually issue the FW close port command
   until the last port user issues a CLOSE_PORT request.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.

CC: Roland Dreier <roland@kernel.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ConnectX devices support a set of flow counters that can be attached
to a set containing one or more QPs.  Each such counter tracks receive
and transmit packets and bytes of these QPs.  This patch queries the
device to check support for counters, handles initialization of the
HCA to enable counters, and initializes a bitmap allocator to control
counter allocations.  Derived from patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Query another dword containing up to 32 extended device capabilities
and merge it into struct mlx4_caps.flags.  Update the code that
handles the current extended device capabilities (e.g UDP RSS, WoL,
vep steering, etc) to use the extended device cap flags field instead
of a field per extended capability.  Initial patch done by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The latest firmware adds a second dword containing more device flags,
so extend the device capabilities flags field from 32 to 64 bits.
Derived from patch by Eli Cohen <eli@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.
Signed-off-by: NIgor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The report now based on query from FW, giving the correct tranciever type
and link speed.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
   on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Multi-protocol adapters support different port types.  Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it.  Port type
is configured through a sysfs interface.  When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Get maximum ethernet MTU and default MAC address from the firmware
QUERY_DEV_CAP command.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

For ethernet support, we need to reserve QPs for the ethernet and
fibre channel driver.  The QPs are reserved at the end of the QP
table.  (This way we assure that they are aligned to their size)

We need to consider these reserved ranges in bitmap creation, so we
extend the mlx4 bitmap utility functions to allow reserved ranges at
both the bottom and the top of the range.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for the following operations to mlx4 when device firmware
supports them:

 - Send with invalidate and local invalidate send queue work requests;
 - Allocate/free fast register MRs;
 - Allocate/free fast register MR page lists;
 - Fast register MR send queue work requests;
 - Local DMA L_Key.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There was a bug in some versions of the mlx4 driver in
mlx4_alloc_fmr(), which hardcoded the minimum acceptable page_shift to
be 12.  However, new ConnectX firmware can support a minimum
page_shift of 9 (log_pg_sz of 9 returned by QUERY_DEV_LIM) -- so with
old drivers, ib_fmr_alloc() would fail for ULPs using the device
minimum when creating FMRs.

To preserve firmware compatibility with released mlx4 drivers, the
firmware will continue to return 12 as before for log_page_sz in
QUERY_DEV_CAP for these drivers.  However, to enable new drivers to
take advantage of the available smaller page size, the mlx4 driver now
first sets the log_pg_sz to the device minimum by setting a
log_page_sz value to 0 via the MOD_STAT_CFG command and then reading
the real minimum via QUERY_DEV_CAP.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add TSO support to the mlx4_ib driver.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.

Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set.  Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add an InfiniBand driver for Mellanox ConnectX adapters.  Because
these adapters can also be used as ethernet NICs and Fibre Channel 
HBAs, the driver is split into two modules: 
 
  mlx4_core: Handles low-level things like device initialization and 
    processing firmware commands.  Also controls resource allocation 
    so that the InfiniBand, ethernet and FC functions can share a 
    device without stepping on each other. 
 
  mlx4_ib: Handles InfiniBand-specific things; plugs into the 
    InfiniBand midlayer. 
Signed-off-by: NRoland Dreier <rolandd@cisco.com>