I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.

In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace code of the following form:

sizeof(*tx_msg) + le16_to_cpu(tx_msg->num_pls) * sizeof(tx_msg->pld[0]);

with:

struct_size(tx_msg, pld, le16_to_cpu(tx_msg->num_pls));

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for FEC encoding control, user can change
FEC mode by command ethtool --set-fec, and get FEC mode by command
ethtool --show-fec. The fec capability is changed follow the port
speed. If autoneg on, the user configure fec mode will be overwritten
by autoneg result.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, our driver only supports phydev to autoneg or change
port speed. This patch adds support for fibre port, driver gets
media speed capability and autoneg capability from firmware. If
the media supports multiple speeds, user can change port speed
with command "ethtool -s <devname> speed xxxx autoneg off duplex
full". If autoneg on, the user configuration may be overwritten
by the autoneg result.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.

The new port information looks like this:
Settings for eth0:
        Supported ports: [ FIBRE ]
        Supported link modes:   25000baseCR/Full
                                25000baseSR/Full
                                1000baseX/Full
                                10000baseCR/Full
                                10000baseSR/Full
                                10000baseLR/Full
        Supported pause frame use: Symmetric
        Supports auto-negotiation: No
        Supported FEC modes: None BaseR
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: Not reported
        Speed: 10000Mb/s
        Duplex: Full
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: off
        Current message level: 0x00000036 (54)
                               probe link ifdown ifup
        Link detected: yes

In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipheth_carrier_set() is called from two locations. In
ipheth_carrier_check_work(), its parameter 'dev' is set with
container_of(work, ...) and can not be NULL. In ipheth_open(),
dev is extracted from netdev_priv(net) and dereferenced before
the call to ipheth_carrier_set(). The NULL pointer check of dev
in ipheth_carrier_set() is therefore unnecessary and can be removed.

Cc: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces "recovery mode" to the i40e driver. It is
part of a new Any2Any idea of upgrading the firmware. In this
approach, it is required for the driver to have support for
"transition firmware", that is used for migrating from structured
to flat firmware image. In this new, very basic mode, i40e driver
must be able to handle particular IOCTL calls from the NVM Update
Tool and run a small set of AQ commands.

These additional AQ commands are part of the interface used by
the NVMUpdate tool.  The NVMUpdate tool contains all of the
necessary logic to reference these new AQ commands.  The end user
experience remains the same, they are using the NVMUpdate tool to
update the NVM contents.
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Signed-off-by: NPiotr Marczak <piotr.marczak@intel.com>
Tested-by: NDon Buchholz <donald.buchholz@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Printing each devices PCI vendor and device ID has the advantage of
easily revealing what hardware we're dealing with exactly. It's no
longer necessary to match the PCI bus information to the lspci output.

Helps with bug reports where no lspci output is available.

Output before
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0
and after
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0 [8086:1572] [8086:0004]
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A refactor of the i40e_vc_config_promiscuous_mode_msg function moved
the check for un-trusted VF into another function. We have to lie to
an un-trusted VF that its request to set promiscuous mode is
successful even when it is not because we don't want the VF to find
out its trust status this way. With the refactor, we were running into
a case where even though we were not setting promiscuous mode for an
un-trusted VF, we still printed a misleading message that it was
successful.

This patch fixes that by ensuring that a success message is printed
on the host side only when the promiscuous mode change has been
successful.
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just bumping the version number appropriately.
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function i40e_validate_cloud_filter checks that the destination and
source port numbers are valid by attempting to ensure that the number is
non-zero and no larger than 0xFFFF. However, the types for the dst_port
and src_port variable are __be16 which by definition cannot be larger
than 0xFFFF

Since these values cannot be larger than 2 bytes, the check to see if
they exceed 0xFFFF is meaningless.

One might consider these checks as some sort of defensive coding, in
case the type was later changed. However, these checks also byte-swap
the value before comparison using be16_to_cpu, which will truncate the
values to 16bits anyways. Additionally, changing the type would require
updating the opcodes to support new data layout of these virtchnl
commands.

Remove the check to silence the -Wtype-limits warning that was added to
GCC 8.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This code implements driver code changes necessary for LLDP
Agent support. Modified i40e_aq_start_lldp() and
i40e_aq_stop_lldp() adding false parameter whether LLDP state
should be persistent across power cycles.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add assignments for advertising 40GBase_LR4, 40GBase_CR4 and fibre
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to changes in FW the SW is required to perform double SR dump in
some cases.

Implementation adds two new steps to update nvm checksum function:
* recalculate checksum and check if checksum in NVM is correct
* if checksum in NVM is not correct then update it again
Signed-off-by: NMaciej Paczkowski <maciej.paczkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VF's attempt to delete vlan 0 when a port vlan is configured is harmless
in this case pf driver just does nothing.  If vf will try to remove
other vlans when a port vlan is configured it will still produce error
as before.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

TX MDD events reported on the PF are the result of the
PF misconfiguring a descriptor and not because of "bad actions"
by anything else.  No need to reset now because if it
results in a Tx hang, the Tx hang check will take care of it.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the driver behavior when detecting a VF MDD event.
It now disables the VF after one event, which indicates a hw detected
problem in the VF.  Before this change, the PF would allow a couple of
events before doing the reset.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ethernet flow control:

The switch MAC does not consume, nor does it emit pause frames. It
simply forwards them as any other Ethernet frame (and since the DMAC is,
per IEEE spec, 01-80-C2-00-00-01, it means they are filtered as
link-local traffic and forwarded to the CPU, which can't do anything
useful with them).

Duplex:

There is no duplex setting in the SJA1105 MAC. It is known to forward
traffic at line rate on the same port in both directions. Therefore it
must be that it only supports full duplex.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).

But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.

As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.

So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If STP is active, this setting is applied on bridged ports each time an
Ethernet link is established (topology changes).

Since the setting is global to the switch and a reset is required to
change it, resets are prevented if the new callback does not change the
value that the hardware already is programmed for.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.

Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/ethernet.txt is confusing because
it says what the MAC should not do, but not what it *should* do:

  * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
     should not add an RX delay in this case)

The gap in semantics is threefold:
1. Is it illegal for the MAC to apply the Rx internal delay by itself,
   and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before
   passing it to of_phy_connect? The documentation would suggest yes.
1. For "rgmii-rxid", while the situation with the Rx clock skew is more
   or less clear (needs to be added by the PHY), what should the MAC
   driver do about the Tx delays? Is it an implicit wild card for the
   MAC to apply delays in the Tx direction if it can? What if those were
   already added as serpentine PCB traces, how could that be made more
   obvious through DT bindings so that the MAC doesn't attempt to add
   them twice and again potentially break the link?
3. If the interface is a fixed-link and therefore the PHY object is
   fixed (a purely software entity that obviously cannot add clock
   skew), what is the meaning of the above property?

So an interpretation of the RGMII bindings was chosen that hopefully
does not contradict their intention but also makes them more applied.
The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings
if the port is in the PHY role (either explicitly, or if it is a
fixed-link). Otherwise it always passes the duty of setting up delays to
the PHY driver.

The error behavior that this patch adds is required on SJA1105E/T where
the MAC really cannot apply internal delays. If the other end of the
fixed-link cannot apply RGMII delays either (this would be specified
through its own DT bindings), then the situation requires PCB delays.

For SJA1105P/Q/R/S, this is however hardware supported and the error is
thus only temporary. I created a stub function pointer for configuring
delays per-port on RXC and TXC, and will implement it when I have access
to a board with this hardware setup.

Meanwhile do not allow the user to select an invalid configuration.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.

On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.

IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NGeorg Waibel <georg.waibel@sensor-technik.de>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This structure was used intensively for machine specific values
when DT was not used. Since the removal of AVR32 from the kernel,
this structure is only used for passing clocks from PCI macb wrapper, all
other fields being 0.
All other known platforms use DT.

Remove the leftovers but make sure that PCI macb still works as
expected by using default values:
- phydev->irq is set to PHY_POLL by mdiobus_alloc()
- mii_bus->phy_mask is cleared while allocating it
- bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found
in DT.

This simplifies driver probe path and particularly phy handling.
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While moving the chunk of code during 739de9a1
("net: macb: Reorganize macb_mii bringup"), the declaration of
struct phy_device declaration was kept. It's not useful in this
function as we alrady have a phydev pointer.
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: d84aec42 ("net: ll_temac: Fix support for 64-bit platforms")
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_err makes more sense than dev_info when this call fails.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the link event flow works, but can be much better.
Refactor the link event flow to make it cleaner and more clear
on what is going on.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PHY type ICE_PHY_TYPE_LOW_25G_AUI_C2C is missing from
ice_get_settings_link_up() which is causing a warning
message for unrecognized PHY.  Add the PHY type to
correctly set the settings and avoid the warning message.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Every time we want to re-enable interrupts and/or write to a register
that requires an interrupt vector's hardware index we do the following:

vsi->hw_base_vector + q_vector->v_idx

This is a wasteful operation, especially in the hot path. Fix this by
adding a u16 reg_idx member to the ice_q_vector structure and make the
necessary changes to make this work.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Runtime change of PFINT_OICR_ENA register is unnecessary.
The handlers should always clear the atomic bit for each
task as they start, because it will make sure that any late
interrupt will either 1) re-set the bit, or 2) be handled
directly in the "already running" task handler.
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes issue with non trusted VFs being able to add more than
permitted number of VLANs by adding a check in ice_vc_process_vlan_msg.
Also don't return an error in this case as the VF does not need to know
that it is not trusted.

Also rework ice_vsi_kill_vlan to use the right types.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In ice_vsi_ctrl_rx_rings() we are unnecessarily waiting for
QRX_CTRL_QENA_REQ and QRX_CTRL_QENA_STAT to be the same value prior to
disabling each Rx queue. There is no reason to do this so remove
this wait loop as we already have a wait loop after disabling/enabling
the Rx queue through the QRX_CTRL register to make sure it gets
successfully disabled/enabled.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the driver allows rx-usecs-high values to be set,
but when querying the device for rx-usecs-high the value
does not stick. This is because it was not yet implemented.
Add code to allow the user to change rx-usecs-high and
use this to set the q_vector's intrl value.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>