mlx4_en_select_queue() uses __skb_tx_hash to select the transmit queue.
XPS settings are ignored by this. Instead, we can use __netdev_pick_tx
to select the transmit queue.

Compile test only.
Signed-off-by: Ngovindarajulu.v <govindarajulu90@gmail.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4 driver has a suboptimal memory allocation strategy for regular
MTU=1500 frames, as it uses two page fragments :

One of 512 bytes and one of 1024 bytes.

This makes GRO less effective, as each GSO packet contains 8 MSS instead
of 16 MSS.

Performance of a single TCP flow gains 25 % increase with the following
patch.

Before patch :

A:~# netperf -H 192.168.0.2 -Cc
MIGRATED TCP STREAM TEST ...
Recv   Send    Send                          Utilization       Service Demand
Socket Socket  Message  Elapsed              Send     Recv     Send    Recv
Size   Size    Size     Time     Throughput  local    remote   local   remote
bytes  bytes   bytes    secs.    10^6bits/s  % S      % S      us/KB   us/KB

 87380  16384  16384    10.00      13798.47   3.06     4.20     0.436   0.598

After patch :

A:~# netperf -H 192.68.0.2 -Cc
MIGRATED TCP STREAM TEST ...
Recv   Send    Send                          Utilization       Service Demand
Socket Socket  Message  Elapsed              Send     Recv     Send    Recv
Size   Size    Size     Time     Throughput  local    remote   local   remote
bytes  bytes   bytes    secs.    10^6bits/s  % S      % S      us/KB   us/KB

 87380  16384  16384    10.00      17273.80   3.44     4.19     0.391   0.477
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch improves the logic used by the mvneta driver to find a MAC
address for a particular interface. Until now, it was only looking at
the Device Tree, and if no address was found, was falling back to
generating a random MAC address.

This patch adds the intermediate solution of reading the MAC address
from the hardware registers, in case it has been set by the
bootloader. So the order is now:

 1) MAC address from the Device Tree
 2) MAC address from the hardware registers
 3) Random MAC address

This requires moving the MAC address initialization a little bit later
in the ->probe() code, because it now requires the hardware registers
to be remapped.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just fixed a typo in emac_probe().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

76723bca "net: mv643xx_eth: add DT parsing support" added a
dummy mv643xx_eth_shared_of_probe() fallback function with a
typo.

This adds the missing semicolon so we can build without CONFIG_OF
again, and changes both dummy functions to the more conventional
"static inline" syntax, which can avoid potential problems with
the empty macro.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this is a pull-request for net-next/master. It consists of two patches
by Fabio Estevam, cleaning up the flexcan driver (remove default
pinctrl and switch to SIMPLE_DEV_PM_OPS). A patch by me to simplify the
Kconfig [1] handling for flexcan. And a patch by Jingoo Han that
converts the can drivers to use platform_{get,set}_drvdata().

[1] My patch touches arch/{arm,powerpc}, so I collected Acked-bys from
Arnd Bergmann, Shawn Guo and Benjamin Herrenschmidt.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we don't need scope id, we should initialize it to zero.
Same for ->sin6_flowinfo.

Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Acked-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_create_hash() is only called from netdev_init() which is marked
__net_init.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

s/allocal/allocate/
Signed-off-by: NJens Renner <renner@efe-gmbh.de>
Acked-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current code style.

Remove extern from function prototypes.
Align function arguments and reflow to 80 cols.
Use network comment styles.
Signed-off-by: NJoe Perches <joe@perches.com>
cc: Lorenzo Colitti <lorenzo@google.com>,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 202dc3fc (Documentation: remove
obsolete networking/multicast.txt file) deleted the obsolete file. After
the file has been removed, clean up a couple of places where references
to the deleted file were made so that users wouldn't be confused when
they consult the Help menu.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up unnecessary initialization of enumerators as the compiler takes
care of that.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up unnecessary assignment and jump. While there, fix up the label
name.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding phy-mode to CPSW node for beaglebone, EVM and EVMsk.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding phy-mode support to cpsw driver and updating the cpsw binding
documentation.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add phy_id device tree data to am335x-evmsk device to bring up CPSW
ethernet present on am335x starter kit.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable Atheros 803X phy driver support in defconfig which is present in
AM335x EVM and EVM Starter Kit.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for Atheros 8031 phy driver.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for RGMII TX delay configuration on Atheros 803X,
this can be enabled in debug registers. With this patch,
PHY_INTERFACE_MODE_RGMII_TXID modes are now supported.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WOL is initilized in phy config_init, but there are standard apis
(set_wol/get_wol) for WOL in phy frame work. So this patch moves
WOL specific code from config_init to wol standard apis.

Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of phy_drivers_register/phy_drivers_unregister to register/unregister
multiple phy drivers in a single module.

Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The format is based on /proc/net/icmp and /proc/net/{udp,raw}6.

Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Couldn't figure out how to test without CONFIG_PROC_FS enabled.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a ping_seq_afinfo structure (similar to its UDP
equivalent) and use it to make some of the ping /proc functions
address-family independent. Rename the remaining ping /proc
functions from ping_* to ping_v4_*.

Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

udp6_sock_seq_show and raw6_sock_seq_show are identical, except
the UDP version displays ports and the raw version displays the
protocol. Refactor most of the code in these two functions into
a new common ip6_dgram_sock_seq_show function, in preparation
for using it to display ICMPv6 sockets as well.

Also reduce the indentation in parts of include/net/transp_v6.h
to improve readability.

Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the indentation of most of the functions and make it a
bit more consistent. This allows longer function and arg names
to be consistently indented without wrapping.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch removes the Kconfig symbol HAVE_CAN_FLEXCAN from arch/{arm,powerpc}
and allowing compilation unconditionally on all arm and powerpc platforms.

This brings a bigger compile time coverage and removes the following dependency
warning found by Arnd Bergmann:

    warning: (SOC_IMX28 && SOC_IMX25 && SOC_IMX35 && IMX_HAVE_PLATFORM_FLEXCAN &&
        SOC_IMX53 && SOC_IMX6Q) selects HAVE_CAN_FLEXCAN
    which has unmet direct dependencies (NET && CAN && CAN_DEV)
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Using SIMPLE_DEV_PM_OPS can make the code smaller and simpler.

Also change CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.

Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: <linux-can@vger.kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Pci_enable_device() will set device pm state to D0, so
it's no need to do it again in tg3_init_one().
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct icmp_bxm is a large struct, reduce stack usage
by allocating it on heap.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ICMP_PARAMETERPROB is handled by icmp_unreach(); This patch adds
ICMP_PARAMETERPROB to the list of ICMP message types handled by icmp_unreach().
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MCA support has been removed but this dependency escaped removal.
Also, there is a duplicate PPC_PSERIES dependency that appeared
when the ethernet drivers were separated into vendor/model
specific directories, so we remove that here as well.
Reported-by: NRobert de Rooy <robert.de.rooy@gmail.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 13d82bf5 (ipv4: Fix flushing of cached routing informations)
added the support to flush learned pmtu information.

However, using rt_genid is quite heavy as it is bumped on route
add/change and multicast events amongst other places. These can
happen quite often, especially if using dynamic routing protocols.

While this is ok with routes (as they are just recreated locally),
the pmtu information is learned from remote systems and the icmp
notification can come with long delays. It is worthy to have separate
genid to avoid excessive pmtu resets.

Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tunnel devices call update_pmtu for each packet sent, this causes
contention on the fnhe_lock. Ignore the pmtu update if pmtu is not
actually changed, and there is still plenty of time before the entry
expires.
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>