Tested on i.MX25 and i.MX35 and i.MX51
Signed-off-by: NEric Bénard <eric@eukrea.com>

Signed-off-by: NEric Bénard <eric@eukrea.com>

the PHY is UTMI so don't create an ULPI viewpoint.
Signed-off-by: NEric Bénard <eric@eukrea.com>

* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID

* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: NEric Bénard <eric@eukrea.com>

So the correct clock will be taken for each of the two independent
controllers.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Addiontionally make the interrupt #defines match the base address
defines MX.._NFC_BASE_ADDR.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The driver recently learned to handle platform ids.  Make use of this
new feature.  The up side is that the driver needs less knowledge about
the spi interfaces used on different SoCs.
Acked-by: NJason Wang <jason77.wang@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

For mx1_defconfig this yields:

	add/remove: 1/0 grow/shrink: 1/4 up/down: 49/-108 (-59)
	function                                     old     new   delta
	imx1_imx_uart_data                             -      48     +48
	kernel_config_data                          7277    7278      +1
	imx_add_imx_uart_1irq                        132     128      -4
	imx_add_imx_uart_3irq                        164     156      -8
	scb9328_init                                  96      64     -32
	mx1ads_init                                  220     156     -64

for mx21_defconfig this yields:

	add/remove: 1/0 grow/shrink: 0/3 up/down: 64/-52 (12)
	function                                     old     new   delta
	imx21_imx_uart_data                            -      64     +64
	imx_add_imx_uart_3irq                        160     156      -4
	imx_add_imx_uart_1irq                        140     136      -4
	mx21ads_board_init                           220     176     -44

for a random mx25 config this yields:

	add/remove: 1/0 grow/shrink: 0/5 up/down: 80/-56 (24)
	function                                     old     new   delta
	imx25_imx_uart_data                            -      80     +80
	imx_add_imx_uart_3irq                        160     156      -4
	imx_add_imx_uart_1irq                        140     136      -4
	mx25pdk_init                                 288     272     -16
	eukrea_mbimxsd_baseboard_init                272     256     -16
	eukrea_cpuimx25_init                         252     236     -16

for mx27_defconfig this yields:

	add/remove: 1/0 grow/shrink: 0/10 up/down: 96/-280 (-184)
	function                                     old     new   delta
	imx27_imx_uart_data                            -      96     +96
	imx_add_imx_uart_3irq                        160     156      -4
	imx_add_imx_uart_1irq                        140     136      -4
	pca100_init                                  560     544     -16
	mx27pdk_init                                 112      96     -16
	mx27lite_init                                 92      76     -16
	eukrea_cpuimx27_init                         332     316     -16
	pcm038_init                                  388     348     -40
	mxt_td60_board_init                          320     280     -40
	eukrea_mbimx27_baseboard_init                476     436     -40
	mx27ads_board_init                           368     280     -88

and finally for mx3_defconfig:

	add/remove: 2/0 grow/shrink: 0/9 up/down: 128/-344 (-216)
	function                                     old     new   delta
	imx31_imx_uart_data                            -      80     +80
	imx35_imx_uart_data                            -      48     +48
	imx_add_imx_uart_1irq                        132     128      -4
	imx_add_imx_uart_3irq                        164     152     -12
	mx31moboard_devboard_init                    360     344     -16
	mx31lite_db_init                             176     160     -16
	mx31moboard_smartbot_init                    384     360     -24
	kzm_board_init                               232     208     -24
	armadillo5x0_init                            392     364     -28
	mx31lilly_db_init                            248     208     -40
	mxc_board_init                              3760    3580    -180
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Group soc specific data in a global struct instead of repeating it for
each call to imxXX_add_spi_imxX.  The structs holding the actual data
are placed in .init.constdata and so don't do much harm.  Compared to
the previous approach this reduces code size to call imx_add_spi_imx.
Acked-by: NJason Wang <jason77.wang@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

The build failure was introduced by

	13dd0c97 (USB: otg/ulpi: extend the generic ulpi driver.)
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Last change I did made a big mess in function names and CONFIG names,
this patch fixes this so that the baseboard support is really built
when selected.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The commit 9a763bfb "get rid of mxc_gpio_init" changed gpio_init
and irq_init sequence. Usually we will call set_irq_chained_handler
in gpio_init functions, this should be called after the irq_init
called, otherwise the chained irq can't get propoer irq_chip and this
irq will remain masked even we called set_irq_chained_handler.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Tested-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

as per suggested by Sascha
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch fixes the following Kconfig warning :
"arch/arm/mach-mx25/Kconfig:18:warning: choice value used outside its
choice group
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

In order to make this patch compile, even if the flexcan driver with
it's header defining the platform data isn't merged yet, two ifdefs have
been added. They effect that the "imx_add_flexcan" function results in a
no-op function if the driver hasn't been activated.

These ifdefs can be removed after the flexcan driver has been merged.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

DEBUG_LL is actually broken on i.MX25, this patch fix it.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host
and USB OTG
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* add clocks for audmux and ssi 1 & 2
* add irq for ssi 1 & 2
* add devices platform for ssi1 & 2
* update audmux-v2 for i.MX25
* add base addresses for audmux & ssi 1 & 2
* add iomux configuration for GPIO for AUD5 port
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

usb drivers need to get the right value for otg clock so
calculate and return it
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

the standard place for this define is include/mach/mx25.h
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The keymap is taken from the Freescale supplied kernel.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Make use of new mechanism to register a nand device.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This function is defined once for each imx family and so is in the way
when compiling a kernel for more than one SoC.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Additionally document all known names of that machine.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>