In 2.6.34, we transformed the PCI DMA API into the generic device
mode. The PCI DMA API is just the wrapper of the DMA API.

So we don't need HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_SIZE or
HAVE_ARCH_PCI_SET_DMA_SEGMENT_BOUNDARY (which enable architectures to
have the own implementations). Both haven't been used anyway.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.

A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.

Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

During suspend on an SMP system, {read,write}_msi_msg_desc() may be
called to mask and unmask interrupts on a device that is already in a
reduced power state.  At this point memory-mapped registers including
MSI-X tables are not accessible, and config space may not be fully
functional either.

While a device is in a reduced power state its interrupts are
effectively masked and its MSI(-X) state will be restored when it is
brought back to D0.  Therefore these functions can simply read and
write msi_desc::msg for devices not in D0.

Further, read_msi_msg_desc() should only ever be used to update a
previously written message, so it can always read msi_desc::msg
and never needs to touch the hardware.
Tested-by: N"Michael Chan" <mchan@broadcom.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The CONFIG_PCIEASPM option is confusing and potentially dangerous. ASPM is
a hardware mediated feature rather than one under direct OS control, and
even if the config option is disabled the system firmware may have turned
on ASPM on various bits of hardware. This can cause problems later -
various hardware that claims to support ASPM does a poor job of it and may
hang or cause other difficulties. The kernel is able to recognise this in
many cases and disable the ASPM functionality, but only if CONFIG_PCIEASPM
is enabled.

Given that in its default configuration this option will either leave the
hardware as it was originally or disable hardware functionality that may
cause problems, it should by default y. The only reason to disable it
ought to be to reduce code size, so make it dependent on CONFIG_EMBEDDED.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: lrodriguez@atheros.com
Cc: maximlevitsky@gmail.com
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

I encountered the problem that /proc/bus/pci/XX/YY is not removed even
after the corresponding device is hot-removed, if the file is still
being opened. In addtion, accessing this file in this situation causes
kernel panic (see below).

Becasue the pci_proc_detach_device() doesn't call remove_proc_entry()
if struct proc_dir_entry->count > 1, access to /proc/bus/pci/XX/YY
would refer to struct pci_dev that was already freed.

Though I don't know why the check for proc_dir_entry->count was added,
I don't think it is needed. Removing this check fixes the problem.

Steps to reproduce
------------------
# cd /sys/bus/pci/slots/2/
# PROC_BUS_PCI_FILE=/proc/bus/pci/`awk -F: '{print $2"/"$3}' < address`.0
# sleep 10000 < $PROC_BUS_PCI_FILE &
# echo 0 > power
# while true; do cat $PROC_BUS_PCI_FILE > /dev/null; done

Oops Messages
-------------
BUG: unable to handle kernel NULL pointer dereference at 00000042
IP: [<c05c82d5>] pci_user_read_config_dword+0x65/0xa0
*pdpt = 000000002185e001 *pde = 0000000476a79067
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1c.0/0000:10:00.0/local_cpus
Modules linked in: autofs4 sunrpc cpufreq_ondemand acpi_cpufreq ipv6 dm_mirror dm_region_hash dm_log dm_mod e1000e i2c_i801 i2c_core iTCO_wdt igb sg pcspkr dca iTCO_vendor_support ext4 mbcache jbd2 sd_mod crc_t10dif lpfc mptsas scsi_transport_fc mptscsih mptbase scsi_tgt scsi_transport_sas [last unloaded: microcode]

Pid: 2997, comm: cat Not tainted 2.6.34-kk #32 SB/PRIMEQUEST 1800E
EIP: 0060:[<c05c82d5>] EFLAGS: 00010046 CPU: 19
EIP is at pci_user_read_config_dword+0x65/0xa0
EAX: 00000002 EBX: e44f1800 ECX: e144df14 EDX: 155668c7
ESI: 00000087 EDI: 00000000 EBP: e144df40 ESP: e144df0c
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process cat (pid: 2997, ti=e144c000 task=e26f2570 task.ti=e144c000)
Stack:
 c09ceac0 c0570f72 ffffffff 08c57000 00000000 00001000 e44f1800 c05d2404
<0> e144df40 00001000 00000000 00001000 08c57000 3093ae50 e420cb40 e358d5c0
<0> c05d2300 fffffffb c054984f e144df9c 00008000 08c57000 e358d5c0 00008000
Call Trace:
 [<c0570f72>] ? security_capable+0x22/0x30
 [<c05d2404>] ? proc_bus_pci_read+0x104/0x220
 [<c05d2300>] ? proc_bus_pci_read+0x0/0x220
 [<c054984f>] ? proc_reg_read+0x5f/0x90
 [<c05497f0>] ? proc_reg_read+0x0/0x90
 [<c050694d>] ? vfs_read+0x9d/0x190
 [<c04958f4>] ? audit_syscall_entry+0x204/0x230
 [<c0506a81>] ? sys_read+0x41/0x70
 [<c0402f1f>] ? sysenter_do_call+0x12/0x28
Code: b4 26 00 00 00 00 b8 20 88 b1 c0 c7 44 24 08 ff ff ff ff e8 3e 52 22 00 f6 83 24 04 00 00 20 75 34 8b 43 08 8d 4c 24 08 8b 53 1c <8b> 70 40 89 4c 24 04 89 f9 c7 04 24 04 00 00 00 ff 16 89 c6 f0
EIP: [<c05c82d5>] pci_user_read_config_dword+0x65/0xa0 SS:ESP 0068:e144df0c
CR2: 0000000000000042
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove unnesessary casts from void*.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCI SIG documentation for the _OSC OS/firmware handshaking interface
states:

"If the _OSC control method is absent from the scope of a host bridge
device, then the operating system must not enable or attempt to use any
features defined in this section for the hierarchy originated by the host
bridge."

The obvious interpretation of this is that the OS should not attempt to use
PCIe hotplug, PME or AER - however, the specification also notes that an
_OSC method is *required* for PCIe hierarchies, and experimental validation
with An Alternative OS indicates that it doesn't use any PCIe functionality
if the _OSC method is missing. That arguably means we shouldn't be using
MSI or extended config space, but right now our problems seem to be limited
to vendors being surprised when ASPM gets enabled on machines when other
OSs refuse to do so. So, for now, let's just disable ASPM if the _OSC
method doesn't exist or refuses to hand over PCIe capability control.
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Found one PCIe Module with several bridges built-in where a "cold"
hotadd doesn't work.

If we end up reassigning bridge windows at hotadd time, and have to loop
through assigning new ranges, we won't end up enabling the child bridges
because the first assignment pass already tried to enable them, which
prevents __pci_bridge_assign_resource from updating the windows.

So try to move enabling of child bridges to the end, and only do it
once.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Removed check to prevent hotplug of display devices within shpchp.
Originally this was thought to have been required within the PCI
Hotplug specification for some legacy devices.  However there is
no such requirement in the most recent revision. The check prevents
hotplug of not only display devices but also computational GPUs
which require serviceability.
Signed-off-by: NPraveen Kalamegham <praveen@nextio.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pciehp_unconfigure_device() should return -EINVAL, not EINVAL.
Signed-off-by: NPraveen Kalamegham <praveen@nextio.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The aspm code will currently set the configured aspm policy before drivers
have had an opportunity to indicate that their hardware doesn't support it.
Unfortunately, putting some hardware in L0 or L1 can result in the hardware
no longer responding to any requests, even after aspm is disabled. It makes
more sense to leave aspm policy at the BIOS defaults at initial setup time,
reconfiguring it after pci_enable_device() is called. This allows the
driver to blacklist individual devices beforehand.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Use resource_size_t for MMIO address instead of unsigned long. Otherwise,
higher 32-bits of MMIO address are cleared unexpectedly in x86-32 PAE.
Acked-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pci_enable_device can fail. In that case, a printed warning would be
more appropriate.
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJunchang Wang <junchangwang@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Assigning zero where NULL should be used.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

MSI delivery from on-board ahci controller doesn't work on K8M800.  At
this point, it's unclear whether the culprit is with the ahci
controller or the host bridge.  Given the track record and considering
the rather minimal impact of MSI, disabling it seems reasonable.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NRainer Hurtado Navarro <publio.escipion.el.africano@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In all AMD 780 family northbridges, the vendor ID of the internal
graphics PCI/PCI bridge reads not as AMD but as that of the mainboard
vendor, because the hardware actually returns the value of the subsystem
vendor ID (erratum 18).

We currently have additional quirk entries for Asus and Acer, but it is
likely that we will encounter more systems with other vendor IDs.

Since we do not know in advance all possible vendor IDs, a better way to
find the device is to declare the quirk on the host bridge, whose ID is
always correct, and use that device as a stepping stone to find the PCI/
PCI bridge, if present.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The SLOT_REG_RSVDZ_MASK macro is normally used like this:
	slot_reg &= ~SLOT_REG_RSVDZ_MASK;
The ~ operator has higher precedence than the | operator from inside the
macro, so it needs parenthesis.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some compiler generates following warnings:

  In function 'aer_isr':
  warning: 'e_src.id' may be used uninitialized in this function
  warning: 'e_src.status' may be used uninitialized in this function

Avoid status flag "int ret" and return constants instead, so that
gcc sees the return value matching "it is initialized" better.
Acked-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch (as1388) changes the way the PCI core handles runtime PM
settings when probing or unbinding drivers.  Now the core will make
sure the device is enabled for runtime PM, with a usage count >= 1,
when a driver is probed.  It does the same when calling a driver's
remove method.

If the driver wants to use runtime PM, all it has to do is call
pm_runtime_pu_noidle() near the end of its probe routine (to cancel
the core's usage increment) and pm_runtime_get_noresume() near the
start of its remove routine (to restore the usage count).  It does not
need to mess around with setting the runtime state to enabled,
disabled, active, or suspended.

The patch updates e1000e and r8169, the only PCI drivers that already
use the existing runtime PM interface.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In TPS6507x, depending on the status of DEFDCDC{2,3} pin either
DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.

The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).

Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.
Signed-off-by: NAnuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.

Example spurious message:

	gpio_unexport: gpio0 status -22
Signed-off-by: NJon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NUwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The MPC85xx EDAC driver is missing module device aliases, so the driver
won't load automatically on boot.  This patch fixes the issue by adding
proper MODULE_DEVICE_TABLE() macros.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the logic while writing new date/time to the chip.  The driver
incorrectly wrote back register values to different registers and even
with wrong mask.  The patch adds clearing of the VLF register, which
should be cleared if all date/time values are set.
Signed-off-by: NRudolf Marek <rudolf.marek@sysgo.com>
Acked-by: NWan ZongShun <mcuos.com@gmail.com>
Cc: Martyn Welch <martyn.welch@gefanuc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A driver needs to be ready to take an interrupt as soon as it registers
an interrupt handler. I noticed the following oops when testing kdump:

ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
ibmvscsi 30000002: SRP_VERSION: 16.a
ibmvscsi 30000002: SRP_VERSION: 16.a
Unable to handle kernel paging request for data at address 0x00000000
...
pc: c000000004085e34: .tasklet_action+0xf4/0x1dc
...
c000000004086fe4 .__do_softirq+0x16c/0x2c0
c00000000403138c .call_do_softirq+0x14/0x24
c00000000400ee14 .do_softirq+0xa0/0x104
c00000000408690c .irq_exit+0x70/0xd0
c00000000400f190 .do_IRQ+0x214/0x2a8
c000000004004804 hardware_interrupt_entry+0x1c/0x98
--- Exception: 501 (Hardware Interrupt) at c00000000400c544 .raw_local_irq_restore+0x48/0x54
c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0
c0000000040e7f00 .__setup_irq+0x2ec/0x3f0
c0000000040e8198 .request_threaded_irq+0x194/0x22c
c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0
c00000000446c764 .ibmvscsi_probe+0x688/0x710
c00000000402903c .vio_bus_probe+0x37c/0x3e4
c000000004403f10 .driver_probe_device+0xec/0x1b8
c000000004404088 .__driver_attach+0xac/0xf4
c000000004403184 .bus_for_each_dev+0x98/0x104
c000000004403c98 .driver_attach+0x40/0x60
c0000000044026f0 .bus_add_driver+0x154/0x324
c0000000044045d0 .driver_register+0xe8/0x1ac
c00000000402b2a8 .vio_register_driver+0x54/0x74
c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0
c000000004009834 .do_one_initcall+0x98/0x1d8
c0000000049005b4 .kernel_init+0x27c/0x33c
c000000004031550 .kernel_thread+0x54/0x70

srp_task needs to be setup before request_irq. The patch below fixes the oops.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In the case of platform_device_add() fail, we should call
platform_device_put() instead of platform_device_del()
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

We use voltage selector as an array index for typ_voltages.
Thus the valid range for voltage selector should be 0..voltages_len-1.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Patch 9e39f7c5 changed the
DBG_PRINT() macro and the if clause was wrongly changed. It means
that currently all the DBG_PRINT are being printed, flooding the
kernel log buffer with things like:

s2io: eth6: Next block at: c0000000b9c90000
s2io: eth6: In Neterion Tx routine
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: NSreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix error from the last pull request.  Making sure we shut the panel off
is more correct and saves power.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We didn't free policy->related_cpus in error path err_unlock_policy.
This is catched by following kmemleak report:

unreferenced object 0xffff88022a0b96d0 (size 512):
  comm "modprobe", pid 886, jiffies 4294689177 (age 780.694s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8111ebe5>] create_object+0x186/0x281
    [<ffffffff814fad4f>] kmemleak_alloc+0x60/0xa7
    [<ffffffff8111127a>] kmem_cache_alloc_node_notrace+0x120/0x142
    [<ffffffff81262e4f>] alloc_cpumask_var_node+0x2c/0xd7
    [<ffffffff81262f0b>] alloc_cpumask_var+0x11/0x13
    [<ffffffff81262f1c>] zalloc_cpumask_var+0xf/0x11
    [<ffffffff8140fac0>] cpufreq_add_dev+0x11f/0x547
    [<ffffffff81334bda>] sysdev_driver_register+0xc2/0x11d
    [<ffffffff8140e334>] cpufreq_register_driver+0xcb/0x1b8
    [<ffffffffa032e040>] 0xffffffffa032e040
    [<ffffffff810021ba>] do_one_initcall+0x5e/0x15c
    [<ffffffff81087f94>] sys_init_module+0xa6/0x1e6
    [<ffffffff81009bc2>] system_call_fastpath+0x16/0x1b
    [<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: NXiaotian Feng <dfeng@redhat.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: NDave Jones <davej@redhat.com>

395913d0 ("[CPUFREQ] remove rwsem lock
from CPUFREQ_GOV_STOP call (second call site)") is not needed, because
there is no rwsem lock in cpufreq_ondemand and cpufreq_conservative
anymore.  Lock should not be released until the work done.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=1594Signed-off-by: NAndrej Gelenberg <andrej.gelenberg@udo.edu>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NMathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: NDave Jones <davej@redhat.com>

Drop the unnecessary empty stubs in tusb6010.c and avoid
a compile error when building kernel for n8x0.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

RT Systems has put out bunch of ham radio cables based on the FT232RL
chip.  Each cable type has a unique PID, this adds one for the Yaesu VX-7
radios.
Signed-off-by: NCorey Minyard <minyard@acm.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This device needs to be reset when resuming
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 0ede76fc, "USB: remove uses of
URB_NO_SETUP_DMA_MAP" introduced a regression by inadvertantly removing
initialization of the transfer flags.  This caused initialization
failures in the ums-karma driver.  Fix the regression by zeroing it.

While at it, as Alan Stern points out, the initializers for
actual_length and status are handled by the core and error_count
only matters for isochronous urbs, so they don't need to be set here.
Remove them.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bmAttributes field of the SuperSpeed Endpoint Companion Descriptor has
different meanings, depending on the endpoint type.  If the endpoint is
isochronous, the bmAttributes field is the maximum number of packets
within a service interval that this endpoint supports.  If the endpoint is
bulk, it's the number of stream IDs this endpoint supports.

Only set the Mult field of the xHCI endpoint context using the
bmAttributes field if the endpoint is isochronous, and the device is a
SuperSpeed device.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Super speed is also fast enough to let sisusbvga operate.
Therefor expand the checks.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When an attempt is made to read the interface strings of the Artisman
Watchdog USB dongle (idVendor:idProduct 04b4:0526) an error is written
to the dmesg log (uhci_result_common: failed with status 440000) and the
dongle resets itself, resulting in a disconnect/reconnect loop.

Adding the dongle to the list of devices in quirks.c, with the same
quirk Alan Stern's previous patch for the Saitek Cyborg Gold 3D
joystick, stops the device from resetting and allows it to be used with
no problems.
Signed-off-by: NPaul Mortier <mortier@btinternet.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a configured device is reset, the control endpoint's ring is reused.
If control transfers to the device were issued before the device is reset,
the dequeue pointer will be somewhere in the middle of the ring.  If the
device is then issued an address with the set address command, the xHCI
driver must provide a valid input context for control endpoint zero.

The original code would give the hardware the original input context,
which had a dequeue pointer set to the top of the ring.  This would cause
the host to re-execute any control transfers until it reached the ring's
enqueue pointer.  When issuing a set address command for a device that has
just been configured and then reset, use the control endpoint's enqueue
pointer as the hardware's dequeue pointer.

Assumption:  All control transfers will be completed or cancelled before
the set address command is issued to the device.  If there are any
outstanding control transfers, this code will not work.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Without this fix, a USB 3.0 port is downgraded to full speed after a port
reset of a configured device.  The USB 3.0 terminations will be disabled
permanently, and USB 3.0 devices will always enumerate as full speed
devices, until the host controller is unplugged (if it is an ExpressCard)
or the computer is rebooted.

Fajun Chen traced this traced the speed downgrade issue to the port reset
and the interpretation of port status in USB hub driver code.  The hub
code was not testing for the port being a SuperSpeed port, and it fell
through to the else case of Full Speed.

The following patch adds SuperSpeed mapping from the port status, and
fixes the speed downgrade issue.
Reported-by: NFajun Chen <fajun.chen@seagate.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 6c12db90 also seems to have
introduced a bug that is triggered when the command ring is about to wrap.
The inc_enq() function will not have moved the enqueue pointer past the
link TRB.  It is supposed to be moved past the link TRB in prepare_ring(),
which should be called before a TD is enqueued.  However, the
queue_command() function never calls the prepare_ring() function because
prepare_ring() is only supposed to be used for endpoint rings.  That means
the enqueue pointer will not be moved past the link TRB, and will get
overwritten.

The fix is to make queue_command() call prepare_ring() with a fake
endpoint status (set to running).  Then the enqueue pointer will get moved
past the link TRB.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>