Fail the connect and return the proper error code if a client
is started with local IP address and there is no corresponding
loopback listener.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

IRD is not populated on connect request and application is
getting 0 for the value. Fill in the correct value on
connect request.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Set the TOS field in IP header with the value passed in
from application. If there is mismatch between the remote
client's TOS and listener, set the listener Tos to the higher
of the two values.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add NULL check for ibqp event handler before calling it to report
QP events, as it might not initialized.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Use list_for_each_entry_safe macro for the IPv6 addr list
as IPv6 addresses can be deleted while going through the
list.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Disable listeners and disconnect all connected QPs on
a netdev interface down event. On an interface up event,
the listeners are re-enabled.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

On i40iw device close, disconnect all connected QPs by moving
them to error state; and block further QPs, PDs and CQs from
being created. Additionally, make sure all resources have been
freed before deallocating the ibdev as part of the device close.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add support to allow each independent memory region to
be configured for 2MB page size in addition to 4KB
page size.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add support to use physically mapped WQ's and MR's if determined
that the OS registered user-memory for the region is physically
contiguous. This feature will eliminate the need for unnecessarily
setting up and using PBL's when not required.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The SQ head is incorrectly incremented when the number
of WQEs required is greater than the number available.
The fix is to use the I40IW_RING_MOV_HEAD_BY_COUNT
macro. This checks for the SQ full condition first and
only if SQ has room for the request, then we move the
head appropriately.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The flush_code variable in i40iw_bld_terminate_hdr() is obsolete and
the check to set qp->sq_flush is unreachable. Currently flush code is
populated in setup_term_hdr() and both SQ and RQ are flushed always
as part of the tear down flow.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove unnecessary check for return code from
device_init_pestat() and change func to void.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

To be consistent, use the runtime check instead of
conditional compile.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In i40iw_post_send, use the actual page size instead of
encoded page size. This is to be consistent with the
rest of the file.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

It is not necessary to check cm_node->iwdev in
i40iw_rem_ref_cm_node() as it can never be NULL after
a successful call out of i40iw_make_cm_node().
Signed-off-by: NChien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove dead code, which isn't executed because we
return error if the data size is greater than 48 bytes.

Inline data size greater than 48 bytes isn't supported
and the maximum WQE size is 64 bytes.
Signed-off-by: NTatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Some resources are consumed internally and not available to the user.
After hw is initialized, figure out how many resources are consumed
and subtract those numbers from the initial max device capability in
i40iw_query_device().
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Use memcpy for inline data copy in sends
and writes instead of byte by byte copy.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If i40iw_open() fails for any reason, the LAN handler
is not being removed. Modify i40iw_deinit_device()
to always remove the handler.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When creating QPs, ensure init_attr->cap.max_recv_sge
is clipped to MAX_FRAG_COUNT.

Expose MAX_FRAG_COUNT for max_recv_sge and max_send_sge in
i40iw_query_qp().
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Reviewed-By: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Assign each CEQ vector to a different CPU when possible, then
when creating a CQ, use the vector for the CEQ id. This
allows completion work to be distributed over multiple cores.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Passed in page_size was used as encoded value for writing
the WQE and passed in value was usually 4096. This was
working out since bit 0 was 0 and implies 4KB pages,
but would not work for other page sizes.
Signed-off-by: NMustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Set the MAX_IRD and MAX_ORD size negotiated to the maximum
supported values.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Pre-production silicon incorrectly truncates 4 bytes of the MPA
packet in UDP loopback case. Remove the workaround as it is no
longer necessary.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove the parameter to disable message packing and
always enable it.
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add support for QoS on QPs. Upon device initialization,
a map is created from user priority to queue set
handles. On QP creation, use ToS to look up the queue
set handle for use with the QP.
Signed-off-by: NFaisal Latif <faisal.latif@intel.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When creating a FWD rule using tc create also a HW counter
for this rule.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

Currently the code supports only drop rules to possess counters,
add that ability also for fwd rules.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

Currently when calling mlx5_add_flow_rule we accept
only one flow destination, this commit allows to pass
multiple destinations.

This change forces us to change the return structure to a more
flexible one. We introduce a flow handle (struct mlx5_flow_handle),
it holds internally the number for rules created and holds an array
where each cell points the to a flow rule.

From the consumers (of mlx5_add_flow_rule) point of view this
change is only cosmetic and requires only to change the type
of the returned value they store.

From the core point of view, we now need to use a loop when
allocating and deleting rules (e.g given to us a flow handler).
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

When adding a new rule, if we can match it with compare_match_value and
flow tag we might be able to insert the rule to the same fte.
In order to do that, there must be an overlap between the actions of the
fte and the new rule.

When updating the action of an existing fte, we must tell the firmware
we are doing so.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

The way we compare between two dests will need to be used in other
places in the future, so we factor out the comparison logic
between two dests into a separate function.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

An fte status becomes FS_FTE_STATUS_EXISTING only after it was
created in HW. We can use this in order to simplify the logic on
what firmware command to use. If the status isn't FS_FTE_STATUS_EXISTING
we need to create the fte, otherwise we need only to update it.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

When adding a new rule to an fte, we need to hold the fte lock
until we add that rule to the fte and increase the fte ref count.

Fixes: 0c56b975 ("net/mlx5_core: Introduce flow steering API")
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

Implement the vf set rate ndo by modifying the TSAR vport rate limit.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

Add TSAR to the eswitch which will act as the vports rate limiter.
Create/Destroy TSAR on Enable/Dsiable SRIOV.
Attach/Detach vport to eswitch TSAR on Enable/Disable vport.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

TSAR (stands for Transmit Scheduling ARbiter) is a hardware component
that is responsible for selecting the next entity to serve on the
transmit path.
The arbitration defines the QoS policy between the agents connected to
the TSAR.
The TSAR is a consist two main features:
1) BW Allocation between agents:
The TSAR implements a defecit weighted round robin between the agents.
Each agent attached to the TSAR is assigned with a weight and it is
awarded transmission tokens according to this weight.
2) Rate limer per agent:
Each agent attached to the TSAR is (optionally) assigned with a rate
limit.
TSAR will not allow scheduling for an agent exceeding its defined rate
limit.

In this patch we implement the API of manipulating the TSAR.
Signed-off-by: NMohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

For the mlx5 driver to support ConnectX-5 PCIe 4.0 VFs, we add the
device ID "0x101a" to mlx5_core_pci_table.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

According to PRM async_event_mask have to be 64 bits long.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

SRQ physical address structure field should be in big-endian format.
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>

Update struct mlx5_ifc_xrqc_bits according to last specification
Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>