Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 27 1月, 2015 10 次提交
    • B
      sh_eth: Fix DMA-API usage for RX buffers · 52b9fa36
      由 Ben Hutchings 提交于 
      - Use the return value of dma_map_single(), rather than calling
  virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      52b9fa36
    • B
      sh_eth: Check for DMA mapping errors on transmit · aa3933b8
      由 Ben Hutchings 提交于 
      dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      aa3933b8
    • B
      sh_eth: Ensure DMA engines are stopped before freeing buffers · 740c7f31
      由 Ben Hutchings 提交于 
      Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers.  This is unsafe because:

- In general, register writes are not serialised with DMA, so we still
  have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
  be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
  RX DMA at the next packet boundary

I applied this patch to the driver to detect DMA writes to freed
buffers:

> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
>  	/* Free Rx skb ringbuffer */
>  	if (mdp->rx_skbuff) {
>  		for (i = 0; i < mdp->num_rx_ring; i++)
> +			memcpy(mdp->rx_skbuff[i]->data,
> +			       "Hello, world", 12);
> +		msleep(100);
> +		for (i = 0; i < mdp->num_rx_ring; i++) {
> +			WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> +				       "Hello, world", 12));
>  			dev_kfree_skb(mdp->rx_skbuff[i]);
> +		}
>  	}
>  	kfree(mdp->rx_skbuff);
>  	mdp->rx_skbuff = NULL;

then ran the loop:

    while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done

and 'ping -f' toward the sh_eth port from another machine.  The
warning fired several times a minute.

To fix these issues:

- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
  perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
  frame, disable egress and wait a reasonable time to reach a
  packet boundary before resetting
- Update statistics before resetting

(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      740c7f31
    • B
      sh_eth: Remove RX overflow log messages · dc1d0e6d
      由 Ben Hutchings 提交于 
      If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse.  These errors are visible in the
statistics anyway.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      dc1d0e6d
    • E
      net: mv643xx_eth: Fix highmem support in non-TSO egress path · 9e911414
      由 Ezequiel Garcia 提交于 
      Commit 69ad0dd7
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date:   Mon May 19 13:59:59 2014 -0300

    net: mv643xx_eth: Use dma_map_single() to map the skb fragments

caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.

This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.

This commit also fixes the error path in txq_init() to release the
resources properly.

Fixes: 69ad0dd7 ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9e911414
    • B
      sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers · 283e38db
      由 Ben Hutchings 提交于 
      In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq().  This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it.  Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.

I could easily trigger a crash by running the loop:

   while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done

and 'ping -f' toward the sh_eth port from another machine.

To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
  should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
  and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
  sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
  handlers before clearing EESIPR in sh_eth_close() and
  sh_eth_set_ringparam()

After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      283e38db
    • B
      sh_eth: Fix crash or memory leak when resizing rings on device that is down · 084236d8
      由 Ben Hutchings 提交于 
      If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      084236d8
    • B
      sh_eth: Detach net device when stopping queue to resize DMA rings · bd888916
      由 Ben Hutchings 提交于 
      We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned.  Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.

What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.

I could easily trigger this by running the loop:

   while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      bd888916
    • B
      sh_eth: Fix padding of short frames on TX · eebfb643
      由 Ben Hutchings 提交于 
      If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding.  This could result in leaking sensitive
data.  We also pass different lengths to dma_map_single() and
dma_unmap_single().

Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      eebfb643
    • M
      drivers: net: cpsw: discard dual emac default vlan configuration · 02a54164
      由 Mugunthan V N 提交于 
      In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.

Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.

Fixes: d9ba8f9e (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      02a54164
  3. 25 1月, 2015 2 次提交
  5. 24 1月, 2015 1 次提交
  7. 20 1月, 2015 5 次提交
  9. 16 1月, 2015 11 次提交
  11. 15 1月, 2015 6 次提交
  13. 14 1月, 2015 3 次提交
    • S
      net: fec: fix MDIO bus assignement for dual fec SoC's · 3d125f9c
      由 Stefan Agner 提交于 
      On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.

Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)

This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.

However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3d125f9c
    • M
      drivers: net: cpsw: fix multicast flush in dual emac mode · 25906052
      由 Mugunthan V N 提交于 
      Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.

Fixes: d9ba8f9e (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      25906052
    • H
      cxgb4vf: Initialize mdio_addr before using it · fd48e639
      由 Hariprasad Shenai 提交于 
      In commit 5ad24def ("cxgb4vf: Fix ethtool get_settings for VF driver")
mdio_addr of port_info structure was used unininitialzed. Fixing it.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fd48e639
  15. 13 1月, 2015 1 次提交
  17. 12 1月, 2015 1 次提交