o Earlier, set_drv_version was getting called after register_netdev.
  This was resulting in a race between set_drv_version and FLR called
  from open(). Moving set_drv_version before register_netdev avoids
  the race.

o Log response code in error message on CDRP failure.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Aggregating tx stats in adapter variable was resulting in
  an increase in stats even after no traffic was run and
  user runs ifconfig/ethtool command.
o qlcnic_update_stats used to accumulate stats in adapter
  struct at each function call, instead accumulate tx stats
  in local variable and then assign it to adapter structure.
Reported-by: NHolger Kiehl <holger.kiehl@dwd.de>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent commit "e29aa339 bna: Enable Multi Buffer RX" is causing
a performance regression. It does not properly update 'cmpl' pointer
at the end of the loop in NAPI handler bnad_cq_process(). The result is
only one packet / per NAPI-schedule is processed.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A driver should fill magic field of ethtool_eeprom struct in .get_eeprom
and validate it in .set_eeprom. The bna incorrectly validates it in both
and this makes its .get_eeprom interface unusable.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sunvnet driver doesn't check whether or not a port is connected when
transmitting packets, which results in failures if a port fails to connect
(e.g., due to a version mismatch). The original code also assumes
unnecessarily that the first port is up and a switch, even though there is
a flag for switch ports.

This patch only matches a port if it is connected, and otherwise uses the
switch_port flag to send the packet to a switch port that is up.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When TSO packet is transmitted additional BD w/o mapping is used
to describe the packed. The BD needs special handling in tx
completion.

kernel: Call Trace:
kernel: <IRQ>  [<ffffffff815e19ba>] dump_stack+0x19/0x1b
kernel: [<ffffffff8105dee1>] warn_slowpath_common+0x61/0x80
kernel: [<ffffffff8105df5c>] warn_slowpath_fmt+0x5c/0x80
kernel: [<ffffffff814a8c0d>] ? find_iova+0x4d/0x90
kernel: [<ffffffff814ab0e2>] intel_unmap_page.part.36+0x142/0x160
kernel: [<ffffffff814ad0e6>] intel_unmap_page+0x26/0x30
kernel: [<ffffffffa01f55d7>] bnx2x_free_tx_pkt+0x157/0x2b0 [bnx2x]
kernel: [<ffffffffa01f8dac>] bnx2x_tx_int+0xac/0x220 [bnx2x]
kernel: [<ffffffff8101a0d9>] ? read_tsc+0x9/0x20
kernel: [<ffffffffa01f8fdb>] bnx2x_poll+0xbb/0x3c0 [bnx2x]
kernel: [<ffffffff814d041a>] net_rx_action+0x15a/0x250
kernel: [<ffffffff81067047>] __do_softirq+0xf7/0x290
kernel: [<ffffffff815f3a5c>] call_softirq+0x1c/0x30
kernel: [<ffffffff81014d25>] do_softirq+0x55/0x90
kernel: [<ffffffff810673e5>] irq_exit+0x115/0x120
kernel: [<ffffffff815f4358>] do_IRQ+0x58/0xf0
kernel: [<ffffffff815e94ad>] common_interrupt+0x6d/0x6d
kernel: <EOI>  [<ffffffff810bbff7>] ? clockevents_notify+0x127/0x140
kernel: [<ffffffff814834df>] ? cpuidle_enter_state+0x4f/0xc0
kernel: [<ffffffff81483615>] cpuidle_idle_call+0xc5/0x200
kernel: [<ffffffff8101bc7e>] arch_cpu_idle+0xe/0x30
kernel: [<ffffffff810b4725>] cpu_startup_entry+0xf5/0x290
kernel: [<ffffffff815cfee1>] start_secondary+0x265/0x27b
kernel: ---[ end trace 11aa7726f18d7e80 ]---

Fixes: a848ade4 ("bnx2x: add CSUM and TSO support for encapsulation protocols")
Reported-by: NYulong Pei <ypei@redhat.com>
Cc: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow set_settings() to complete succesfully even if link is
not estabilished and port type isn't known yet.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the setting real tx queue
count error handling case instead of 0.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets shorter than ETH_ZLEN were not padded with zeroes, hence leaking
potentially sensitive information. This bug has been present since the
driver got accepted in commit 1c1008c7
("net: bcmgenet: add main driver file").
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a regression introduced by commit 35f6f453 ("net/mlx4_en: Don't use
irq_affinity_notifier to track changes in IRQ affinity map").
When core is started in legacy EQ's (number of IRQ's < rx rings), cq->irq_desc
was NULL.  This caused a kernel crash under heavy traffic - when having more
than rx NAPI budget completions.
Fixed to have it set for both EQ modes.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing cleans up the objects created by
vnet_new(), they are completely leaked.

vnet_exit(), after doing the vio_unregister_driver() to clean
up ports, should call a helper function that iterates over vnet_list
and cleans up those objects. This includes unregister_netdevice()
as well as free_netdev().
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NDave Kleikamp <dave.kleikamp@oracle.com>
Reviewed-by: NKarl Volz <karl.volz@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethernet port on my ASUS A88X Pro mainboard stopped working
several times a day, with messages like these in dmesg:

AMD-Vi: Event logged [IO_PAGE_FAULT device=05:00.0 domain=0x001e address=0x0000000000003000 flags=0x0050]

Searching the web for these messages led me to similar reports about
different hardware supported by r8169, and eventually to commits
3ced8c95 ('r8169: enforce RX_MULTI_EN
for the 8168f.') and eb2dc35d ('r8169:
RxConfig hack for the 8168evl'). So I tried this change, and it fixes
the problem for me.
Signed-off-by: NMichel Dänzer <michel@daenzer.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Napi id was not marked for gro_skb, this will lead rx busy loop won't
work correctly since they stack never try to call low latency receive
method because of a zero socket napi id. Fix this by marking napi id
for gro_skb.

The transaction rate of 1 byte netperf tcp_rr gets about 50% increased
(from 20531.68 to 30610.88).

Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RGMII_MODE_EN bit was defined to 0, while it is actually 6. It was not
much of a problem on older designs where this was a no-op, and the RGMII
data-path would always be enabled, but newer GENET controllers need to
explicitely enable their RGMII data-pad using this bit.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some devices, the internal PLL circuit occasionally provides the
wrong clock frequency after power up. The probability of failure is less
than one failure per 1000 power cycles. When the failure occurs, the
internal clock frequency is around 1/20 of the correct frequency.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In mlx5_core_destroy_mkey(), we must first remove the mr from the
radix tree and then destroy it.  Otherwise we might hit a race if the
key was reallocated and we attempted to insert it to the radix tree.

Also handle radix tree insert/delete failures.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NEli Cohen <elic@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

For RTL8411, RTL8111G, RTL8402, RTL8105, and RTL8106, disable the feature
of entering the L2/L3 link state of the PCIe. When the nic starts the process
of entering the L2/L3 link state and the PCI reset occurs before the work
is finished, the work would be queued and continue after the next the PCI
reset occurs. This causes the device stays in L2/L3 link state, and the system
couldn't find the device.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit fixes the command value generated for CSUM calculation
when running in big endian mode.  The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode.  This patch byte-swaps the ID conditionally with
htons.

Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: NThomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.

This problem exists since c5aff182 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.

Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: NMaggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is recommended that TX work not count against the quota.
The cost of TX packet liberation is a minute percentage of what it costs to
process an RX frame. Furthermore, that SKB freeing makes memory available for
other paths in the stack.

Give the TX a larger budget and be more aggressive about cleaning up the Tx
descriptors this budget could be changed using ethtool:
$ ethtool -C eth1 tx-frames-irq <budget>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The add_vxlan_port ndo driver code was wrongly testing whether HW vxlan offloads
are supported by the device instead of checking if they are currently enabled.

This causes the driver to configure the HW parser to conduct matching for vxlan
packets but since no steering rules were set, vxlan packets are dropped on RX.

Fix that by doing the right test, as done in the del_vxlan_port ndo handler.

Fixes: 1b136de1 ('net/mlx4: Implement vxlan ndo calls')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 0acf1676.

Breaks the build due to missing reference to phy_resume in
the resulting dwmac-socfpga.o object.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

deal with a compile warning: comparison between
'enum qe_fltr_largest_external_tbl_lookup_key_size'
and 'enum qe_fltr_tbl_lookup_key_size'

the code:
	"if (ug_info->largestexternallookupkeysize ==
	     QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES)"
is warned because different enum, so modify it.

	"enum qe_fltr_largest_external_tbl_lookup_key_size
	             largestexternallookupkeysize;

	enum qe_fltr_tbl_lookup_key_size {
		 QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES
			 = 0x3f,         /* LookupKey parsed by the Generate LookupKey
					    CMD is truncated to 8 bytes */
		 QE_FLTR_TABLE_LOOKUP_KEY_SIZE_16_BYTES
			 = 0x5f,         /* LookupKey parsed by the Generate LookupKey
					    CMD is truncated to 16 bytes */
	 };

	 /* QE FLTR extended filtering Largest External Table Lookup Key Size */
	 enum qe_fltr_largest_external_tbl_lookup_key_size {
		 QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_NONE
			 = 0x0,/* not used */
		 QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_8_BYTES
			 = QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES,        /* 8 bytes */
		 QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_16_BYTES
			 = QE_FLTR_TABLE_LOOKUP_KEY_SIZE_16_BYTES,       /* 16 bytes */
	 };"
Signed-off-by: NZhao Qiang <B45475@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cppcheck found a case where a local variable was being assigned a value,
but not used. There seems to be no reason to read this register before
assigning a new value, so addressing thie issue.

cppcheck --force --enable=all --inline-suppr . shows ...

Variable 'value' is reassigned a value before the old one has been used.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cppcheck found a duplicate if/then/else case where a receive descriptor
was being processed. This patch corrects that issue.

cppcheck --force --enable=all --inline-suppr .
...
Checking enh_desc.c...
[enh_desc.c:148] -> [enh_desc.c:144]: (style) Found duplicate if expressions.
...
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to remove affinity hint at mlx4_en_deactivate_cq() and not at
mlx4_en_destroy_cq() - since affinity_mask might be free'd while still
being used by procfs.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQ affinity notifier can only have a single notifier - cpu_rmap
notifier. Can't use it to track changes in IRQ affinity map.
Detect IRQ affinity changes by comparing CPU to current IRQ affinity map
during NAPI poll thread.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2eacc23c ("net/mlx4_core: Enforce irq affinity changes immediatly")
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware will provide this information as soon as we will start
processing incoming packets, so there is no need to set the RX buffer
length during buffer allocation.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use the PHY library which will determine the link state for us, make
sure we start with a carrier off until libphy has completed the link
training.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As soon as register_netdev() is called, the network device notifiers are
running which means that other parts of the kernel, or user-space
programs can call the network device ndo_open() callback and use the
interface.

Disable the Ethernet device clock before we register the network device
such that we do not create the following situation:

CPU0				CPU1
register_netdev()
				bcmgenet_open()
				clk_prepare_enable()
clk_disable_unprepare()

and leave the hardware block gated off, while we think it should be
gated on.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although we do not limit the number of packets the TX completion
function bcm_sysport_tx_reclaim() is allowed to reclaim, we were still
using its return value as-is. This means that we could hit the WARN() in
net/core/dev.c where work_done >= budget.

Make sure we do exit the NAPI context when the TX ring is empty, and
pretend there was no work to do.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The UniMAC CMD_SW_RESET bit is not a self-clearing bit, so we need to
assert it, wait a bit and clear it manually. As a result, umac_reset()
is updated not to return any value. The previous version of the code
simply wrote 0 to the CMD register, which would make the busy-waiting
loop exit immediately, having zero effect.

By writing 0 to the CMD register, we were clearing all bits in the CMD
register, and not using the hardware reset default values which are
set on purpose.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SYSTEMPORT Ethernet MAC supports multicast just fine, it just lacks
any sort of Unicast/Broadcast/Multicasting filtering at the Ethernet MAC
level since that is handled by the front end Ethernet switch, but that
is properly handled by bcm_sysport_set_rx_mode().

Some user-space applications might be relying on the presence of this
flag to prevent using multicast sockets, this also prevents that
interface from joining the IPv6 all-router mcast group.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While it is legal to kfree(NULL), it is not wise to use :
put_page(virt_to_head_page(NULL))

 BUG: unable to handle kernel paging request at ffffeba400000000
 IP: [<ffffffffc01f5928>] virt_to_head_page+0x36/0x44 [bnx2x]
Reported-by: NMichel Lespinasse <walken@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Fixes: d46d132c ("bnx2x: use netdev_alloc_frag()")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MSI-X should use PCI_MSIX_FLAGS not PCI_MSI_FLAGS.
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the mdio probe function fails in emac_open, the interrupt we just requested
isn't freed. If emac_open is called again, for example because we try to set up
the interface again, the kernel will oops because the interrupt wasn't properly
released.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3f85944f ("net: Add sysfs file
for port number") introduce dev_port to network devices. cxgb4 adapters
have multiple ports on the same PCI function, and used dev_id to
identify those ports. That use was removed by commit
8c367fcb ("cxgb4: Do not set
net_device::dev_id to VI index"), since dev_id should be used only when
devices share the same MAC address.

Using dev_port for cxgb4 allows different ports on the same PCI function
to be identified.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>