The Icom ID-1 1.2 GHz band digital transceiver is a new radio
that has a USB interface. With this patch, the ftdi_sio driver
will report "Detected FT8U232AM" and provide a serial device
interface.
Signed-off-by: N"A. Maitland Bottoms" <bottoms@debian.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a new device ID to the cp2101 driver
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

check_ctrlrecip() disallows any control transfers if the device is
deconfigured (in configuration 0, ie.  state ADDRESS).  This for example
makes it impossible to read the device descriptors without configuring the
device, although most standard device requests are allowed in this state by
the spec.  This patch allows control transfers for the ADDRESS state, too.
Signed-off-by: NHorst Schirmeier <horst@schirmeier.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a NULL pointer dereference spotted by the Coverity
checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ZC0301 driver bugfix.

Use correct PID/VID USB entries.
Signed-off-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NWolfgang Rohdewald <wolfgang@rohdewald.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as661) adds an unusual_devs entry for the Mitsumi 7in1 Card
Reader.

From: Rodolfo Quesada <rquesada@roqz.net>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Ref
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=176584Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The following adds an unusual_devs entry for the SanDisk ImageMate CompactFlash
USB drive, for the US_FL_FIX_CAPACITY flag. Additionally, it removes trailing
whitespace from the previous entry. It's based on the patch sent by Roman Hodek
<roman@hodek.net>.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As found by Sam's scripts.

Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When trying to deconfigure a device via usb_set_configuration(dev, 0),
2.6.16-rc kernels after 55c52718 oops
with "Unable to handle NULL pointer dereference at...". This is due to
an unchecked dereference of cp in the power budget part.
Signed-off-by: NHorst Schirmeier <horst@schirmeier.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In a couple of places, usbcore assumes that a USB device configuration
will have a nonzero number of interfaces.  Having no interfaces may or
may not be allowed by the USB spec; in any event we shouldn't die if we
encounter such a thing.  This patch (as662) removes the assumptions.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Matt mentioned that a very old ZIP-100 actually does need this, but I am
yet to see anyone who actually has one still working and uses ub with it.
He/she must be a retrocomputing geek, who can easily bias it to usb-storage
with libusual, if needed. Meanwhile, common folks have trouble with poorly
designed USB keys and some el-cheapo European music players. I think we
better drop this for now.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove the "diag" file from the sysfs. The usbmon is good enough these days
so I do not need this feature anymore. Also, sysfs is a pain. Al Viro caught
a race in this, which I thought too bothersome to fix.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The first_open was long overdue for removal, but I wanted to keep this
separate for other changes in case of regressions.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as657) increases the port-reset completion delay in uhci-hcd
for HP's embedded controllers.  Unlike other UHCI controllers, the HP
chips can take as long as 250 us to carry out the processing associated
with finishing a port reset.

This fixes Novell bug #148761.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The USB data cable for my Samsung GSM phone contains the USB-to-serial
converter chip MS3303H from Speed Dragon Multimedia, Inc.  that appears to
be compatible with the PL2303 chip.  The following patch adds support for
this chip to the pl2303 driver.
Signed-off-by: NDick Streefland <dick@streefland.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A while ago, I posted about TIOCMIWAIT not working with the PL2303
USB-serial adapter.

After a brief exchange with Greg, I tracked this to a missing wake-up
in the USB interrupt procedures. I got our systems staff to install
the enclosed very simple patch to our 2.6.12 kernels, and it all works
fine as expected. I guess this should also apply to the latest version
and go into the mainstream.

Apologies for the long delay in posting the result.

The routine being patched is pl2303_update_line_status
Signed-off-by: NJulian Bradfield <jcb+luu@inf.ed.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the Nokia ca42 version 2 cable to the
cypress_m8 driver.  The device was tested by others with this patch and
found to be compatible with the cypress_m8 driver.  A special note
should be taken that this cable seems to vary in the type of chipset
used.  This patch supports the cable with product id 0x4101.
Signed-off-by: NLonnie Mendez <lmendez19@austin.rr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ZC0301 driver updates.

Changes: + new, - removed, * cleanup, @ bugfix

@ Need usb_get|put_dev() when disconnecting, if the device is open
* Cleanups and updates in the documentation
+ Use per-device sensor structures
+ Add frame_timeout module parameter
Signed-off-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: ET61X[12]51 driver updates

Changes: + new, - removed, * cleanup, @ bugfix

@ Fix stream_interrupt()
@ Fix vidioc_enum_input() and split vidioc_gs_input()
@ Need usb_get|put_dev() when disconnecting, if the device is open
* Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
  when waiting for video frames
* replace wake_up_interruptible(&wait_stream) with wake_up(&wait_stream)
* Cleanups and updates in the documentation
* Use mutexes instead of semaphores
+ Use per-device sensor structures
+ Add support for PAS202BCA image sensors
+ Add frame_timeout module parameter
Signed-off-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

SN9C10x driver updates.

Changes: + new, - removed, * cleanup, @ bugfix

@ Fix stream_interrupt()
@ Fix vidioc_enum_input() and split vidioc_gs_input()
@ Need usb_get|put_dev() when disconnecting, if the device is open
* Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
  when waiting for video frames
* replace wake_up_interruptible(&wait_stream) with wake_up(&wait_stream)
* Cleanups and updates in the documentation
+ Use per-device sensor structures
+ Add support for PAS202BCA image sensors
+ Add frame_timeout module parameter
Signed-off-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this patch converts drivers/usb to kzalloc usage.
Compile tested with allyes config.

I think there was a bug in drivers/usb/gadget/inode.c because
it used sizeof(*data) for the kmalloc() and sizeof(data) for
the memset(), since sizeof(data) just returns the size for a pointer.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds credits about the ZC0301 and ET61X[12]51 USB drivers
which have been included in the mainline kernel recently.
Signed-off-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

"Cosmetic" driver updates for the ZC0301 driver:

- Fix stream_interrupt() (and work around a possible kernel bug);

- Fix vidioc_enum_input() and split vidioc_gs_input() in two parts;
- Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
  when waiting for video frames;
- replace erroneous wake_up_interruptible(&wait_stream) with
  wake_up(&wait_stream);
- Cosmetic cleanups in the documentation.
Signed-off-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Gcc 4.0.2 had the warning:

drivers/usb/media/ov511.c: In function 'show_exposure':
drivers/usb/media/ov511.c:5642: warning: 'exp' may be used uninitialized
in this function

Here is the patch to fix that warning.
Signed-off-by: NMatthew Martin <lihnucks@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch allows you to set the iSerialNumber field in the
usb_device_descriptor structure for your USB ethernet gadget.

It also changes the parameters shown through sysfs so they're
no longer declared as __initdata, preventing potential oopses.

That's most useful for the Ethernet addresses, which may in
some cases be random "locally administered" addresses.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds __init section annotations to gadget driver bind() routines to
remove calls from .text into .init sections (for endpoint autoconfig).
Likewise it adds __exit section annotations to their unbind() routines.

The specification of the gadget driver register/unregister functions is
updated to explicitly allow use of those sections.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as647) fixes a small error introduced by a recent change to
the USB core suspend/resume code.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as640) removes several put_device and the corresponding
get_device calls from the USB core and HCDs.  Some of the puts were done
in atomic contexts, and none of them are needed since the core now
guarantees that every endpoint will be disabled and every URB completed
before a USB device is released.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A recent update to the uhci-hcd driver invoked the list_prepare_entry
macro incorrectly.  This patch (as646) corrects it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Even when the URB_SHORT_NOT_OK flag is set, a short transfer shouldn't
generate a debugging log message.  Especially not one with the confusing
claim that the transfer "failed with status 0".  This patch (as627)
fixes that behavior in uhci-hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as626) makes some improvements to the debugging code in
uhci-hcd.  The main change is that now the code won't get compiled if
CONFIG_USB_DEBUG isn't set.  But there are other changes too, like
adding a missing .owner field and printing a debugging dump if the
controller dies.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As part of reorienting uhci-hcd away from URBs and toward endpoint
queues, this patch (as625) eliminates the driver's main list of URBs.
The list wsa used mainly in checking for URB completions; now the driver
goes through the list of active endpoints and checks the members of the
queues.

As a side effect, I had to remove the code that looks for FSBR timeouts.
For now, FSBR will remain on so long as any URBs on a full-speed control
or bulk queue request it, even if the queue isn't advancing.  A later
patch can add more intelligent handling.  This isn't a huge drawback;
it's pretty rare for an URB to get stuck for more than a fraction of a
second.  (And it will help the people trying to use those insane HP USB
devices.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as624) fixes a hardware race in uhci-hcd by adding a dummy
TD to the end of each endpoint's queue.  Without the dummy the host
controller will effectively turn off the queue when it reaches the end,
which happens asynchronously.  This leads to a potential problem when
new transfer descriptors are added to the end of the queue; they may
never get used.

With a dummy TD present the controller never turns off the queue;
instead it just stops at the dummy and leaves the queue on but inactive.
When new TDs are added to the end of the queue, the first new one gets
written over the dummy.  Thus there's never any question about whether
the queue is running or needs to be restarted.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as623) changes the uhci-hcd driver to make it use one QH per
device endpoint, instead of a QH per URB as it does now.  Numerous areas
of the code are affected by this.  For example, the distinction between
"queued" URBs and non-"queued" URBs no longer exists; all URBs belong to
a queue and some just happen to be at the queue's head.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In setting up the of PHY we masked off too many bits, instead just
initialize PORTSC for the type of PHY we are using.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NFranck Bui-Huu <vagabon.xyz@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>