When operating in client mode, the short period of time between scanning
and associating is often enough to put the hardware through several
FULL-SLEEP <-> AWAKE transitions, each wakeup requiring a reset to fully
recover the hardware.
This is completely unnecessary and can easily be avoided by deferring
the switch to full sleep.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use CONFIG_ATH9K_TX99 to properly enclose the tx99 code
and make sure that it is not compiled as part of the driver
when it is not selected. Move the tx99 code to a new file tx99.c
and also add ATH9K_DEBUGFS as a dependency in Kconfig.

This reduces the module size on platforms like OpenWrt where
ATH9K_DEBUGFS is selected, but TX99 might be disabled.

Cc: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the PLL is turned off for AR9485 when
switching to a low power state, but AR9485 has an issue
where the card will become unresponsive if left idle
for a long time without any traffic. To fix this,
force the PLL to always be on using a different initval
array, ar9485_1_1_pll_on_cdr_on_clkreq_disable_L1.

This is done for most of the AR9485 based cards
like HB125, WB225 etc. but certain models require the
feature to be turned off. Identify such cards and use
default values for them.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX99 support enables Specific Absorption Rate (SAR) testing.
SAR is the unit of measurement for the amount of radio frequency(RF)
absorbed by the body when using a wireless device. The RF
exposure limits used are expressed in the terms of SAR, which is a
measure of the electric and magnetic field strength and power density
for transmitters operating at frequencies from 300 kHz to 100 GHz.

Regulatory bodies around the world require that wireless device
be evaluated to meet the RF exposure limits set forth in the
governmental SAR regulations.

In the examples below, for more bit rate options see the iw TX bitrate
setting documentation:

http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates

Example usage:

iw phy phy0 interface add moni0 type monitor
ip link set dev moni0 up

iw dev moni0 set channel 36 HT40+
iw set bitrates mcs-5 4

echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power
echo 1  > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add spectral scan feature on HT40 channels for ath9k. This patch extends
previous capability added by Simon Wunderlich
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Reviewed-by: NSimon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Tested-by: NSimon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not exposed as a configuration option anyway
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no shared code for handling both rx and tx buffers, and tx
buffers require a lot more metadata than rx buffers.
Using a separate data structure for rx reduces memory usage and improves
cache footprint.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever the return value of snprintf() is used to calculate
remaining buffer-space, we wanted to use sncprintf() instead.

Indentation is adapted where possible. Some lines exceed the
line width limit, either they did it already before, or
since they can not be broken reasonably well.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are 2 types of WB335 cards, 1-antenna and 2-antenna.
Identify them based on PCI subsystem IDs, this will be used
for MCI/BTCOEX tweaks.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These cards are based on WB335/AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: NJoe Perches <joe@perches.com>

The PCIE Workaround register (AR_WA/0x4004) is used to handle
various hardware quirks. For AR9002 chips, AR_WA_D3_L1_DISABLE
is used to prevent the HW from automatically entering L1 state
when D3 is enforced.

AR_WA_D3_L1_DISABLE has to be enabled for a few AR9280 based
cards, mark them based on their PCI subdevice/subvendor IDs
and enforce it in ar9002_hw_configpcipowersave().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CSA is only enabled for one interface, but the same limitation applies
for mac80211 too. It checks whether the beacon has been sent (different
approaches for non-EDMA-enabled and EDMA-enabled devices), and completes
the channel switch after that.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 uses debugfs_remove_recursive, so there's no need for the
driver to do an explicit cleanup of its sta debugfs entry.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also reduce the size of a few fields where possible
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar to a race condition that exists in the tx path, the hardware
might re-read the 'next' pointer of a descriptor of the last completed
frame. This only affects non-EDMA (pre-AR93xx) devices.

To deal with this race, defer clearing and re-linking a completed rx
descriptor until the next one has been processed.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Create a per-vif dummy node entry for keeping the multicast software
queues. This helps in setups with a lot of mulitcast traffic that could
otherwise potentially drown out unicast traffic to stations.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a first step for improving fairness between legacy and 802.11n
traffic, and it should also improve reliability of resets and channel
changes by keeping the hardware queue depth very short.

When an aggregation session is torn down, all packets in the retry queue
will be removed from the BAW and freed.

For all subframes that have not been transmitted yet, the A-MPDU flag
will be cleared, and a sequence number allocated. This ensures that the
next A-MPDU session will get the correct initial sequence number.
This happens both on aggregation session start and stop.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a packet has been tracked as part of the BlockAck window and added
to the hardware queue, it can end up back in the TID queue again with
fi->retries still set to 0 (e.g. if the frame was filtered). Keep an
extra bit for the BAW tracking status to fix this corner case.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The check for ATH_AMPDU_SUBFRAME_DEFAULT is unnecessary, since it's set
to half the maximum BlockAck Window size, which is already the maximum
value that h_baw could possibly have. Also remove unnecessary variables.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Improves packet retry order and helps with further tx queueing
improvements.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During a HW reset, the diversity config is programmed
in the set_board_values() eeprom callback, there is no
need to do it again by calling ath_ant_comb_update().

Fixed antenna support is not fully handled for 1-stream
cards, it can be done later.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make use of this capability to restrict the usage of the
debugfs file and modparam using which this feature can
be enabled.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS198/CUS230 need a few tweaks in the antenna diversity
algorithm to accomodate RSSI variation. Add a couple
of knobs to control low RSSI threshold and fast antenna
diversity bias values.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Right now, it is being done for all cases.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When antenna diversity combining is enabled in the EEPROM,
the initial values for the MAIN/ALT config have to be
programmed correctly. This patch adds it for AR9285.

Since the diversity combining macros are common to all chip
families, remove the redundant AR9285 macros and move the
definitions to phy.h.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since platform support is required for WoW, identify and
and enable Wow only for supported cards.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS217 is a card based on AR9462.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS198 and CUS230 are similar cards, both
are AR9485 + xLNA solutions. But, the subsystem IDs
differ - identify CUS230 explicitly to make things
clearer.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.

Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201

Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The CAB (Content after Beacon) queue is used for beacon-triggered
transmission of buffered multicast frames. If lots of multicast frames
were buffered and this queue fills up, it drowns out all regular
traffic. To limit the damage that buffered traffic can do, try to limit
the queued data to becaon_interval / 8.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for PS-Poll and U-APSD driver-buffered frames (part of
an aggregation session).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the UAPSD hardware queue to get PS-Poll responses out as fast as
possible and without backoff.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Waiting for all subframes of an existing aggregation session to drain
before allowing mac80211 to start a new one is fragile and deadlocks
caused by this behavior have been observed.

Since mac80211 has proper synchronization for aggregation session
start/stop handling, a better approach to session handling is to simply
allow mac80211 to start a new session at any time. This requires
changing the code to discard any packets outside of the BlockAck window
in the A-MPDU software retry code.

This patch implements the above and also simplifies the code.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>