Make sure MTU mask flag is set using new field upon set port
request. In addition, move this code into a helper function for better
code readability.
Signed-off-by: NShaker Daibes <shakerd@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When starting the port, driver will inform Firmware about the actual MTU
which does not include implicit headers, such as FCS or VLAN tags.
Signed-off-by: NShaker Daibes <shakerd@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This feature will allow the user to disable auto negotiation
on the port for mlx4 devices while setting the speed is limited
to 1GbE speeds.
Other speeds will not be accepted in autoneg off mode.

This functionality is permitted providing that the firmware
is compatible with this feature.
The above is determined by querying a new dedicated capability
bit in the device.
Signed-off-by: NAriel Levkovich <lariel@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid reading num_tc directly from struct net_device, but use
the helper function netdev_get_num_tc.

Fixes: bc6a4744 ("net/mlx4_en: num cores tx rings for every UP")
Fixes: f5b6345b ("net/mlx4_en: User prio mapping gets corrupted when changing number of channels")
Signed-off-by: NAlaa Hleihel <alaa@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to aid debugging of functions that take a resource but
don't put it, add the last function name that successfully grabbed
this resource.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device revision field returned by the NodeInfo MAD is incorrect
on ConnectX3 devices.

This patch is driver side handling to complete a FW fix added at 2.11.1172.
INIT_HCA - bit at offset 0x0C.12 is set to 1 so that FW will report
correct device revision.

Older FW versions won't be affected from turning on that bit,
no capability bit is needed.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conform the following warning:
WARNING: ENOSYS means 'invalid syscall nr' and nothing else.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing about lwt state requires a device reference, so remove the
input argument.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d303
("net: gro: add a per device gro flush timer")

This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets arriving in a VRF currently are delivered to UDP sockets that
aren't bound to any interface. TCP defaults to not delivering packets
arriving in a VRF to unbound sockets. IP route lookup and socket
transmit both assume that unbound means using the default table and
UDP applications that haven't been changed to be aware of VRFs may not
function correctly in this case since they may not be able to handle
overlapping IP address ranges, or be able to send packets back to the
original sender if required.

So add a sysctl, udp_l3mdev_accept, to control this behaviour with it
being analgous to the existing tcp_l3mdev_accept, namely to allow a
process to have a VRF-global listen socket. Have this default to off
as this is the behaviour that users will expect, given that there is
no explicit mechanism to set unmodified VRF-unaware application into a
default VRF.
Signed-off-by: NRobert Shearman <rshearma@brocade.com>
Acked-by: NDavid Ahern <dsa@cumulusnetworks.com>
Tested-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: CFP support

This patch series adds support for the Broadcom Compact Field Processor (CFP)
which is a classification and matching engine built into most Broadcom switches.

We support that using ethtool::rxnfc because it allows all known uses cases from
the users I support to work, and more importantly, it allows the selection of a
target rule index, which is later used by e.g: offloading hardware, this is an
essential feature that I could not find being supported with cls_* for instance.

Thanks!

Changes in v3:

- rebased against latest net-next/master after Vivien's changes

Changes in v2:

- fixed modular builds reported by kbuild test robot
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for configuring classification rules using the
ethtool::rxnfc API.  This is useful to program the switch's CFP/TCAM to
redirect specific packets to specific ports/queues for instance. For
now, we allow any kind of IPv4 5-tuple matching.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Compact Field Processor definitions for the Broadcom Starfighter 2
and compatible versions of the switch.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, all traffic goes to queue 0, re-configure the traffic
classes to quality of service mapping such that priority X maps to queue
X, where X is from 0 through 7.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for adding support for CFP/TCAMP in the bcm_sf2 driver add the
plumbing to call into driver specific {get,set}_rxnfc operations.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds devm_alloc_etherdev_mqs function and devm_alloc_etherdev
macro. These can be used for simpler netdev allocation without having to
care about calling free_netdev.

Thanks to this change drivers, their error paths and removal paths may
get simpler by a bit.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are two fixes for batman-adv for net-next:

 - fix double call of dev_queue_xmit(), caused by the recent introduction
   of net_xmit_eval(), by Sven Eckelmann

 - Fix includes for IS_ERR/ERR_PTR, by Sven Eckelmann
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the retransmission stats are not incremented if the
retransmit fails locally. But we always increment the other packet
counters that track total packet/bytes sent.  Awkwardly while we
don't count these failed retransmits in RETRANSSEGS, we do count
them in FAILEDRETRANS.

If the qdisc is dropping many packets this could under-estimate
TCP retransmission rate substantially from both SNMP or per-socket
TCP_INFO stats. This patch changes this by always incrementing
retransmission stats on retransmission attempts and failures.

Another motivation is to properly track retransmists in
SCM_TIMESTAMPING_OPT_STATS. Since SCM_TSTAMP_SCHED collection is
triggered in tcp_transmit_skb(), If tp->total_retrans is incremented
after the function, we'll always mis-count by the amount of the
latest retransmission.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two stats in SCM_TIMESTAMPING_OPT_STATS:

TCP_NLA_DATA_SEGS_OUT: total data packets sent including retransmission
TCP_NLA_TOTAL_RETRANS: total data packets retransmitted

The names are picked to be consistent with corresponding fields in
TCP_INFO. This allows applications that are using the timestamping
API to measure latency stats to also retrive retransmission rate
of application write.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Timur Tabi says:

====================
net: qcom/emac:

Although not related, these patches affect the same files, so they should
be applied in order.

The first patch cleans up logging of when the the phy driver is attached.

The second patch always configures the SGMII to use autonegotiation mode.

The third patch removes a redundant call to emac_mac_start().

The fourth patch removes some extraneous non-functioning WOL code.

The fifth patch adds an error handler for the SGMII block.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SGMII (internal PHY) can report decode errors via an interrupt.  It
can also report autonegotiation status changes, but we don't need to track
those.  The SGMII can recover automatically from most decode errors, so
we only reset the interface if we get multiple consecutive errors.

It's possible for bogus decode errors to be reported while the link is
being brought up.  The interrupt is registered when the interface is
opened, and it's enabled after the link is up.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EMAC driver does not support wake-on-lan, but there is still
code left-over that partially enables it.  Remove that code and a few
macros that support it.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

emac_mac_start() uses information from the external PHY to program
the MAC, so it makes no sense to call it before the link is up.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Regardless of how the external PHY is configured, the internal PHY
(the "SGMII" block) is capable of configuring the SGMII link automatically.
When the external PHY link comes up, regardless of how it is configured,
the SGMII link is configured automatically.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY driver is attached only when the driver calls
phy_connect_direct().  Calling phy_attached_print() to display
information about the PHY driver prior to that point is meaningless.
The interface can be brought down, a new PHY driver can be loaded,
and the interface then brought back up.  This is the correct time
to display information about the attached driver.

Since phy_attached_print() also prints information about the
interrupt, that needs to be set as well.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

do_execute_actions() implements a worthwhile optimization: in case
an output action is the last action in an action list, skb_clone()
can be avoided by outputing the current skb. However, the
implementation is more complicated than necessary.  This patch
simplify this logic.
Signed-off-by: NAndy Zhou <azhou@ovn.org>
Acked-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: preparatory patches for multi-chip

In order to introduce support for multi-chip configuration, we need to
do a few enhancements. This patchset makes the number of ports in a
switch dynamic (instead of capping to DSA_MAX_PORTS), stores the switch
and index of a port in the dsa_port structure, uses it in the slave
private structure, and exposes the bridge device a port belongs to.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.

Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.

Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the bridge_dev pointer from dsa_slave_priv to dsa_port so that DSA
drivers can access this information and remove the need to cache it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store a pointer to the dsa_port structure in the dsa_slave_priv
structure, instead of the switch/port index.

This will allow to store more information such as the bridge device,
needed in DSA drivers for multi-chip configuration.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the physical switch instance and port index a DSA port belongs to to
the dsa_port structure.

That can be used later to retrieve information about a physical port
when configuring a switch fabric, or lighten up struct dsa_slave_priv.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dsa_switch structure contains the number of ports. Use it where the
structure is valid instead of the DSA_MAX_PORTS value.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.

This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Horman says:

====================
ravb: Support 1Gbps on R-Car H3 ES1.1+ and R-Car M3-W

this series adds support for gigabit communication to the Renesas
EthernetAVB controller when used in conjunction with R-Car Gen3 H3
ES1.1+ and M3-W SoCs.  Gigabit is already supported with R-Car Gen 2
SoCs.

The patch from Geert was previously posted for inclusion in v4.10 and
acked by Dave for that purpose. It was, however, not accepted by the
ARM SoC maintainers.

The path from Mizuguchi-san is to address timing problems observed
with gigabit transfers. I would like it considered although my own
testing on M3-W did not show any timing problems.

Changes since v1:
* Address various feedback for "APSR" patch as noted in its changelog
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The limitation to 10/100Mbit speeds on R-Car Gen3 is valid for R-Car H3
ES1.0 only. Check for the exact SoC model to allow 1Gbps on newer
revisions of R-Car H3, and on R-Car M3-W.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables tx and rx clock internal delay modes (TDM and RDM).

This is to address a failure in the case of 1Gbps communication using the
by salvator-x board with the KSZ9031RNX phy. This has been reported to
occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.

With this change APSR internal delay modes are enabled for
"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows:

phy mode   | ASPR delay mode
-----------+----------------
rgmii-id   | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macro is returning ETIME which means various checks to see if
the returned err is less than zero never work. I believe a -ETIME
should be returned instead.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>