It will be used later on by bpf-jit

[ralf@linux-mips.org: Fixed conflict with
49e9529b [MIPS: uasm: add jalr instruction].
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6725/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later one for the jalr and wsbh instructions.

[ralf@linux-mips.org: Dropped arch/mips/include/asm/uasm.h segment because
that was already added by 49e9529b
[MIPS: uasm: add jalr instruction].
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6724/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by the sllv and srlv instructions.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6723/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Sometimes it's useful to let the user, while doing performance research,
know what in the IEEE754 exceptions has caused many times of FP emulation
when running a specific application. This patch adds 5 more files to
/sys/kernel/debug/mips/fpuemustats/, whose filenames begin with "ieee754".
These stats are in addition to the existing cp1ops, cp1xops, errors, loads
and stores, which may not be useful in understanding the reasons of ieee754
exceptions.

[ralf@linux-mips.org: Fixed reject due to other changes to the kernel
FP assist software.]
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Cc: james.hogan@imgtec.com
Patchwork: http://patchwork.linux-mips.org/patch/7044/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Patch was tested on devices with 64 MiB and 256 MiB of RAM.
It documents every part nicely and drops this hacky part of code:
max = off | ((128 << 20) - 1);
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/6808/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add interface mode detection for Octeon II. This is necessary to detect
the interface modes correctly on the UBNT E200 board. Code is taken
from the UBNT GPL source release, with some alterations: SRIO, ILK and
RXAUI interface modes are removed and instead return disabled as these
modes are not currently supported.
Signed-off-by: NAlex Smith <alex.smith@imgtec.com>
Tested-by: NDavid Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7039/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The CONFIG_MIPS_CPS SMP implementation should be able to handle all
cases the CONFIG_MIPS_CMP implementation does, but without requiring
bootloader assistance. It is also required in order to make use of
features such as hotplug & cpuidle core power gating. Enable it by
default for Malta configs that previously enabled the now deprecated
CONFIG_MIPS_CMP, and disable the latter. The local version suffix "cmp"
is removed rather than replaced with "cps" since there are other ways to
tell that the CPS SMP implementation is in use (the "VPE topology" line
in the boot log being one).
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch adds a cpuidle driver for systems based around the MIPS
Coherent Processing System (CPS) architecture. It supports four idle
states:

  - The standard MIPS wait instruction.

  - The non-coherent wait, clock gated & power gated states exposed by
    the recently added pm-cps layer.

The pm-cps layer is used to enter all the deep idle states. Since cores
in the clock or power gated states cannot service interrupts, the
gic_send_ipi_single function is modified to send a power up command for
the appropriate core to the CPC in cases where the target CPU has marked
itself potentially incoherent.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

Declaring this allows drivers which need to initialise each struct
cpuidle_device at initialisation time to make use of the structures
already defined in cpuidle.c, rather than having to wastefully define
their own.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch simply includes the cpuidle Kconfig entries in preparation
for cpuidle drivers used on MIPS systems.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

Defines a macro intended to allow trivial use of the regular MIPS wait
instruction from cpuidle drivers, which may simply invoke the macro
within their array of states.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

Rather than hardcoding CCA=0x5 for secondary cores, re-use the CCA from
the boot CPU. This allows overrides of the CCA using the cca= kernel
parameter to take effect on all CPUs for consistency.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch sets a default CCA suited for use with multi-core SMP on all
current MIPS CPS based systems. It may still be overriden by the cca=
argument on the kernel command line.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

If the user or bootloader sets the CCA to a value which is not suited
for multi-core SMP (ie. anything non-coherent) then limit the system to
using only a single core and warn the user.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch adds support for offlining CPUs via hotplug when using the
CONFIG_MIPS_CPS SMP implementation. When a CPU is offlined one of 2
things will happen:

  - If the CPU is part of a core which implements the MT ASE and there
    is at least one other VPE online within that core then the VPE will
    be halted by settings its TCHalt bit.

  - Otherwise if supported the core will be powered down via the CPC.

  - Otherwise the CPU will hang by executing an infinite loop.

Bringing CPUs back online is then a process of either clearing the
appropriate VPEs TCHalt bit or powering up the appropriate core via the
CPC. Throughout the process the struct core_boot_config vpe_mask field
must be maintained such that mips_cps_boot_vpes will start & stop the
correct VPEs.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch adds code to generate entry & exit code for various low power
states available on systems based around the MIPS Coherent Processing
System architecture (ie. those with a Coherence Manager, Global
Interrupt Controller & for >=CM2 a Cluster Power Controller). States
supported are:

  - Non-coherent wait. This state first leaves the coherent domain and
    then executes a regular MIPS wait instruction. Power savings are
    found from the elimination of coherency interventions between the
    core and any other coherent requestors in the system.

  - Clock gated. This state leaves the coherent domain and then gates
    the clock input to the core. This removes all dynamic power from the
    core but leaves the core at the mercy of another to restart its
    clock. Register state is preserved, but the core can not service
    interrupts whilst its clock is gated.

  - Power gated. This deepest state removes all power input to the core.
    All register state is lost and the core will restart execution from
    its BEV when another core powers it back up. Because register state
    is lost this state requires cooperation with the CONFIG_MIPS_CPS SMP
    implementation in order for the core to exit the state successfully.

The code will detect which states are available on the current system
during boot & generate the entry/exit code for those states. This will
be used by cpuidle & hotplug implementations.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

The core which the CPC core-other region relates to is based upon the
core-local core-other addressing register. As its name suggests this
register is shared between all VPEs within a core, and if there is a
possibility that multiple VPEs within a core will attempt to access
another core simultaneously then locking is required. This wasn't
previously a problem with the only user being cpu0 during boot, but will
be an issue once hotplug is implemented & may race with other users such
as cpuidle.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

The start of mips_cps_core_entry is patched in order to provide the code
with the address of the CM register region at a point where it will be
running non-coherent with the rest of the system. However the cache
wasn't being flushed after that patching which could in principle lead
to secondary cores using an invalid CM base address.

The patching is moved to cps_prepare_cpus since local_flush_icache_range
has not been initialised at the point cps_smp_setup is called.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

The core power down state for cpuidle will require that the CPS SMP
implementation is in use. This patch provides a mips_cps_smp_in_use
function which determines whether or not the CPS SMP implementation is
currently in use.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

When hotplug and/or a powered down idle state are supported cases will
arise where a non-zero VPE must be brought online without VPE 0, and it
where multiple VPEs must be onlined simultaneously. This patch prepares
for that by:

  - Splitting struct boot_config into core & VPE boot config structures,
    allocated one per core or VPE respectively. This allows for multiple
    VPEs to be onlined simultaneously without clobbering each others
    configuration.

  - Indicating which VPEs should be online within a core at any given
    time using a bitmap. This allows multiple VPEs to be brought online
    simultaneously and also indicates to VPE 0 whether it should halt
    after starting any non-zero VPEs that should be online within the
    core. For example if all VPEs within a core are offlined via hotplug
    and the user onlines the second VPE within that core:

      1) The core will be powered up.

      2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to
         initialise the core.

      3) VPE 0 will start VPE 1 because its bit is set in the cores
         bitmap.

      4) VPE 0 will halt itself because its bit is clear in the cores
         bitmap.

  - Moving the core & VPE initialisation to assembly code which does not
    make any use of the stack. This is because if a non-zero VPE is to
    be brought online in a powered down core then when VPE 0 of that
    core runs it may not have a valid stack, and even if it did then
    it's messy to run through parts of generic kernel code on VPE 0
    before starting the correct VPE.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch allows use of the MT ASE yield instruction from uasm. It will
be used by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch allows use of the wait instruction from uasm. It will be used
by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch allows use of the sync instruction from uasm. It will be used
by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch allows use of the jalr instruction from uasm. It will be used
by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This patch allows for use of the beq instruction with labels from uasm,
much as bne & others already do. It will be used by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

The opcode for the wait instruction within POOL32AXf was missing. This
patch adds it for use by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

The opcode for the sync instruction within POOL32AXf was missing. This
patch adds it for use by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

The opcode for the MT ASE yield instruction within the spec3 group was
missing. This patch adds it for use by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

The func field for the wait instruction was missing from inst.h - this
patch adds it.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

Define a macro to write to the current TCs TCHalt register. This will be
used by a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

This is identical to kmap_coherent apart from the cache coherency
attribute used for the TLB entry, so kmap_coherent is abstracted to
kmap_prot which is then called for both kmap_coherent &
kmap_noncoherent. This will be used by a subsequent patch.
Suggested-by: NLeonid Yegoshin <leonid.yegoshin@imgtec.com>
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>

SNI RM code has its own EARLY_PRINTK support no need for some generic 8250
stuff.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6715/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

CONFIG_DMA_COHERENT is no longer set; default to noncoherent io on
Au1200 revision AB to make USB work.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6745/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In arch_setup_msi_irq(), there is no case for PCIe2. So board which have PCIe2 functionality
fails to boot with "Kernel panic - not syncing: arch_setup_msi_irq: Invalid octeon_dma_bar_type"
message. This patch solve this problem.
Signed-off-by: NEunbong Song <eunb.song@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6747/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

These defconfigs contain the CONFIG_M25P80 symbol, which is now
dependent on the MTD_SPI_NOR symbol. Add CONFIG_MTD_SPI_NOR to satisfy
the new dependency.

At the same time, drop the now-nonexistent CONFIG_MTD_CHAR symbol.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Huang Shijie <b32955@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-mtd@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/6878/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Allow 64-bit userspace programs to use ll64 types. The define name
comes from commit 2c9c6ce0 (powerpc:
Add __SANE_USERSPACE_TYPES__ to asm/types.h for LL64).

The patch allows to compile perf on MIPS64 and eliminates the following
warnings:

tests/attr.c:74:4: error: format '%llu' expects argument of type 'long
long unsigned int', but argument 6 has type '__u64' [-Werror=format=]
Signed-off-by: NAaro Koskinen <aaro.koskinen@nsn.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6890/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This timer does not support oneshot mode and as such the system remains
in periodic mode and won't support high res timers.
This patch adds a note about this in Kconfig and lets it depend on
!highres so users which want to use high timers don' stuck with this
timer.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Hua Yan <yanh@lemote.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Hongliang Tao <taohl@lemote.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6935/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Nothing was using the method and there isn't any need for this hook.  This
leaves smp_cpus_done() empty for the moment.

As suggested by Paul Bolle <pebolle@tiscali.nl>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

A few platforms lack a 'device_type = "memory"' for their memory
nodes, relying on an old ppc quirk in order to discover its memory.
Add the missing data so that all parsing code can find memory nodes
correctly.
Signed-off-by: NLeif Lindholm <leif.lindholm@linaro.org>
Acked-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Cc: gaurav.minocha@alumni.ubc.ca
Patchwork: https://patchwork.linux-mips.org/patch/6989/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>