It is necessary to clear MC13892_SWITCHERS0_SWxHI bit when set voltage to the
voltage range from 1100000 to 1375000. Leaving MC13892_SWITCHERS0_SWxHI bit
untouched may result in wrong voltage setting.

For example, currently switch voltage from 1400000 to 1300000 will set the
voltage to 1800000 because the HI bit is still set.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@sirena.org.uk>

It's safe to call regulator_unregister() with NULL, thus remove the NULL test
before regulator_unregister() calls.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@sirena.org.uk>

Patch adds device tree probe support for mc13783-regulator driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMark Brown <broonie@sirena.org.uk>

This patch adds a warning about incorrect regulators instead of
printing the names of non-information message about the wrong amount.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMark Brown <broonie@sirena.org.uk>

Ensure max77686->opmode always has correct status.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@sirena.org.uk>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure to unregister all regulators before return error in probe().

The regulator register order depends on the regulator ID pass to
ab3100_regulator_register() function. Thus we need to scan ab3100_regulator_desc
and find the index of successfully registered regulators, or alternatively just
call ab3100_regulators_remove() to unregister all registered regulators.

Since current code uses a static ab3100_regulators table, explicitly set
reg->rdev = NULL after regulator_unregister() call to ensure calling
ab3100_regulators_remove() in the unwind path always work.

Also move ab3100_regulators_remove() to avoid forward declaration.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Use regulator_map_voltage_ascend for them.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Use regulator_map_voltage_ascend for them.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Use regulator_map_voltage_ascend for them.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Both mc13892_sw1 and mc13892_sw voltage table have ascendant voltage list.
Use regulator_map_voltage_ascend for them.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Use regulator_map_voltage_ascend for them.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

tps65020 ldo1 and ldo2 vsel tables are identical, merge them.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Use regulator_map_voltage_ascend for them.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is necessary to clear MC13892_SWITCHERS0_SWxHI bit when set voltage to the
voltage range from 1100000 to 1375000. Leaving MC13892_SWITCHERS0_SWxHI bit
untouched may result in wrong voltage setting.

For example, currently switch voltage from 1400000 to 1300000 will set the
voltage to 1800000 because the HI bit is still set.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This implements device tree support for the AB3100 regulators
driver. The initial settings are moved out of platform data
and into the driver for the device tree case, as it appears
that there is no way to supply this as AUXDATA for an I2C
device. The style and bindings are heavily inspired by
Lee Jones' style for AB8500.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This refactors the AB3100 regulator probe to use regulator IDs
and pass this to a separate registration function. This works
much smoother when migrating to device tree, as we can use a
match table with this regulator ID encoded in the .driver_data.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current code overrides control1 variable when setting ramp delay bits.
Fix it by just setting ramp_delay bits.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently we have a special code in tps80031_ldo_set_voltage_sel() to handle
LDO2 track mode for TPS80031 or TPS80032-ES1.0. The purpose is to address below
issues:

Issue description:
- LDO2 traking mode is enabled
- LDO2 tracks SMPS2 voltage.
- LDO2 automatically switch-off when LDO2_CFG_VOLTAGE is changed to some discrete values (non exhaustive list):
            00011001, 00011010, 00011011, 00011100, .
- LDO2 switch-on again when LDO2_CFG_VOLTAGE is changed to other values (non exhaustive list):
        00011000, 00010111, .

LDOs have reserved codes. For these codes, LDO is switch-off.

In tracking, LDO2 ref comes from SMPS2.
However LDO2 enable is still gated by LDO2 VSEL decoding.
As a result, in tracking mode LDO2 will be disabled for following code (SMPS VSEL format):
000000 & 100000 (MSB not decoded)
011001 & 111001 (MSB not decoded)
011010 & 111010 (MSB not decoded)
011100 & 111100 (MSB not decoded)
011101 & 111101 (MSB not decoded)
011110 & 111110 (MSB not decoded)

However, current code has below bugs:
1. It uses regulator_list_voltage_linear, so list_voltage() still shows above
   invalid selectors have supported voltage.
2. Current code may return -EINVAL in tps80031_ldo_set_voltage_sel() for
   supported voltage. This is because when we use regulator_list_voltage_linear
   as list_voltage callback, regulator core will default use
   regulator_map_voltage_linear(). regulator_map_voltage_linear() has an
   assumption that the voltages are linear which is not true for this case.

   For example,
   when request voltage range is: min_uV=950000 uV && max_uV=1200000 uV
   regulator_map_voltage_linear() returns the selector is 29 (0x1D),
   set_voltage_sel() returns -EINVAL.
   (The selector is in invalid range, 0x19 ~ 0x1f).

   In above case, map_voltage() should find the lowest valid voltage within
   specific range (selector = 0x20) and set_voltage_sel() should successfully
   set the voltage to 987500 uV.

This patch fixes these issues by:
1. Add checking valid setting for LDO2 track mode of TPS80031 or TPS80032-ES1.0
   in list_voltage.  So it returns -EINVAL for invalid selectors.
2. Implement tps80031_ldo_map_voltage, use regulator_map_voltage_iterate()
   to find the lowest voltage within specific range for TPS80031 or
   TPS80032-ES1.0. This is required when the voltage map is no longer linear.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Thus use regulator_map_voltage_ascend is more efficient than the default
regulator_map_voltage_iterate.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Some regulators have more than 200 supported voltages.
e.g.
For TPS65910_REG_VDD1 and TPS65910_REG_VDD2:
n_voltages = VDD1_2_NUM_VOLT_FINE * VDD1_2_NUM_VOLT_COARSE
           = 73 * 3
           = 219

Thus it worth converting to regulator_map_voltage_ascend rather than use
default regulator_map_voltage_iterate.

For consistent, convert all regulators to regulator_map_voltage_ascend.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Thus use regulator_map_voltage_ascend is more efficient than the default
regulator_map_voltage_iterate.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All regulators have ascendant voltage list in this driver.
Thus use regulator_map_voltage_ascend is more efficient than the default
regulator_map_voltage_iterate.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Simply the [get|set]_voltage_sel implementation by using
regulator_[set|get]_voltage_sel_regmap instead of open coded.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet[1]

Register 0x06h Description: RmpCtrl (REGISTER ADDRESS: 0x06h Read/Write)
BIT[5..7]:
        RMP[2:0] Output voltage ramp timing
        D7-D5   Slope
        000     32mV/us
        001     16mV/us
        010     8mV/us
        ...
        110     0.5mV/us
        111     0.25mV/us

Thus to get correct ramp_ctrl value, we need to right-shift 5 bits.

[1] http://www.ti.com/lit/ds/symlink/tps62360.pdfSigned-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Datasheet says:
Time Step (TSTEP) selection, when changing the output voltage, the new value is
reached through successive voltage steps (if not bypassed). The equivalent
programmable slew rate of the output voltage is:

TSTEP[1:0]: 00 Jump (no slope control)
TSTEP[1:0]: 01 10mV/us
TSTEP[1:0]: 10 5mV/us (default)
TSTEP[1:0]: 11 2.5mV/us
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The ctrl_addr setting for SMPS10 is missed, thus palmas_smps_init() read/write
wrong register for SMPS10 in current code. Fix it.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When building ax88796 on an ARM platform with 64-bit resource_size_t,
we currently get

drivers/net/ethernet/8390/ax88796.c:875: undefined reference to `__aeabi_uldivmod'

because we do a division on the length of the MMIO resource.
Since we know that this resource is very short, using an
"unsigned long" instead of "resource_size_t" is entirely
sufficient, and avoids this link-time error.

Cc: Ben Dooks <ben-linux@fluff.org>
Cc: netdev@vger.kernel.org
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Autoneg is supported on specific port types only. Fix the driver to advertise
autoneg based on the port type.
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Fix the driver to drop error frames in the receive path
o Update error counter which was not getting incremented
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We normally trust and use the CDC functional descriptors provided by a
number of devices.  But some of these will erroneously list the address
reserved for the device end of the link.  Attempting to use this on
both the device and host side will naturally not work.

Work around this bug by ignoring the functional descriptor and assign a
random address instead in this case.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Received packets are sometimes addressed to 00:a0:c6:00:00:00
instead of the address the device firmware should have learned
from the host:

321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request  id=0x4025, seq=64/16384, ttl=64

0000  82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00   .....g.....g..E.
0010  00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a   .T..@.@.W.M.U..z
0020  ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00   ....b.@%.@..nQ..
0030  00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15   ..k.............
0040  16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25   .......... !"#$%
0050  26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35   &'()*+,-./012345
0060  36 37                                             67

321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply    id=0x4025, seq=64/16384, ttl=55

0000  00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00   .......P......E.
0010  00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10   .T.V..7..v.z..M.
0020  55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00   U...j.@%.@..nQ..
0030  00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15   ..k.............
0040  16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25   .......... !"#$%
0050  26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35   &'()*+,-./012345
0060  36 37                                             67

The bogus address is always the same, and matches the address
suggested by many devices as a default address.  It is likely a
hardcoded firmware default.

The circumstances where this bug has been observed indicates that
the trigger is related to timing or some other factor the host
cannot control. Repeating the exact same configuration sequence
that caused it to trigger once, will not necessarily cause it to
trigger the next time. Reproducing the bug is therefore difficult.
This opens up a possibility that the bug is more common than we can
confirm, because affected devices often will work properly again
after a reset.  A procedure most users are likely to try out before
reporting a bug.

Unconditionally rewriting the destination address if the first digit
of the received packet is 0, is considered an acceptable compromise
since we already have to inspect this digit.  The simplification will
cause unnecessary rewrites if the real address starts with 0, but this
is still better than adding additional tests for this particular case.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of LTE devices from different vendors all suffer from the
same firmware bug: Most of the packets received from the device while
it is attached to a LTE network will not have an ethernet header. The
devices work as expected when attached to 2G or 3G networks, sending
an ethernet header with all packets.

This driver is not aware of which network the modem attached to, and
even if it were there are still some packet types which are always
received with the header intact.

All devices supported by this driver have severely limited
networking capabilities:
 - can only transmit IPv4, IPv6 and possibly ARP
 - can only support a single host hardware address at any time
 - will only do point-to-point communcation with the host

Because of this, we are able to reliably identify any bogus raw IP
packets by simply looking at the 4 IP version bits.  All we need to
do is to avoid 4 or 6 in the first digit of the mac address.  This
workaround ensures this, and fix up the received packets as necessary.

Given the distribution of the bug, it is believed that the source is
the chipset vendor.  The devices which are verified to be affected are:
 Huawei E392u-12 (Qualcomm MDM9200)
 Pantech UML290  (Qualcomm MDM9600)
 Novatel USB551L (Qualcomm MDM9600)
 Novatel E362    (Qualcomm MDM9600)

It is believed that the bug depend on firmware revision, which means
that possibly all devices based on the above mentioned chipset may be
affected if we consider all available firmware revisions.

The information about affected devices and versions is likely
incomplete.  As the additional overhead for packets not needing this
fixup is very small, it is considered acceptable to apply the
workaround to all devices handled by this driver.
Reported-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use netif_addr_lock_bh() to acquire the appropriate lock before walking.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

slave_disable_netpoll() is not called upon enslave failure which would
lead to a memory leak. Call slave_disable_netpoll() after err_detach as
that's the first error path after enabling netpoll on that slave.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On enslave failure primary_slave can point to new_slave which is to be
freed, and the same applies to curr_active_slave. So check if this is
the case and clean up properly after err_detach because that's the first
error code path after they're set.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The main problem is with vid refcount which only gets bumped up.
Delete the vlans after err_detach as that's the first error path
after the vlans are added.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.

v2: update log message and don't move code unnecessarily
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>