Decode and log port module error, unknown modules and unsupported
modules.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There could be race between t4_eth_xmit() and t4_free_sge_resources() while
freeing tx descriptors, take txq lock in t4_free_sge_resources(). We need
to stop the xmit frame path which runs in bottom half context while
unloading the driver using _bh variant of the lock. This is to prevent
the deadlock between xmit and driver unload.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new routine to print out general adapter information (various version
numbers, adapter name, part number, serial number, etc.) and remove
redundant information dumped in the Port Information.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Chelsio adapters have two VPD structures stored in the VPD:

  - offset 0x000: an abbreviated VPD, and
  - offset 0x400: the complete VPD.

After 104daa71 ("PCI: Determine actual VPD size on first access"), the
PCI core computes the valid VPD size by parsing the VPD starting at offset
0x0.  That size only includes the abbreviated VPD structure, so reads of
the complete VPD at 0x400 fail.

Explicitly set the VPD size with pci_set_vpd_size() so the driver can read
both VPD structures.

[bhelgaas: changelog, split patches, rename to pci_set_vpd_size() and
return int (not ssize_t)]
Fixes: 104daa71 ("PCI: Determine actual VPD size on first access")
Tested-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Stop all Ethernet RX Queues before freeing up various Ingress/Egress
Queues, etc. We were seeing cases of Ingress Queues not getting serviced
during the shutdown process leading to Ingress Paths jamming up through
the chip and blocking the shutdown effort itself.

One such case involved the Firmware sending a "Flush Token" through the
ULP-TX -> ULP-RX path for an Ethernet TX Queue being freed in order to
make sure there weren't any remaining TX Work Requests in the pipeline.
But the return path was stalled by Ingress Data unable to be delivered to
the Host because those Ingress Queues were no longer being serviced.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Message level can be set through ethtool, so deprecate module parameter
which is used to set the same.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

update Kconfig and Makefile for enabling iSCSI
DDP page pod manager.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

add files for common page pod manager,
both iSCSI initiator and target ULDs will
use common ppod manager for DDP.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

move delayed ack macro definitions to common
header file t4_msg.h.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

move VLAN_NONE macro definition from l2t.c
to l2t.h
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

add members for iSCSI DDP.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

add structure, macro and constant definitions
for iSCSI Tx and Rx.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

move struct cpl_rx_data_ddp definition to
common header file t4_msg.h.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

move struct ulptx_idata definition to
common header file t4_msg.h.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

move struct tcp_options, struct cpl_pass_accept_req,
enum defining congestion control algorithms
and associated macros to common header file t4_msg.h
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

add large receive offload(LRO) support
for upper layer drivers.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

allocate rxqs for non T4 adapters,
dump rxqs sge qinfo through debugfs.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Chelsio iSCSI target offload driver
will register with cxgb4 driver as ULD of type
CXGB4_ULD_ISCSIT.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Acked-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Queue Set Configuration code was always reserving room for a
Forwarded interrupt Queue even in the cases where we weren't using it.
Figure out how many Ports and Queue Sets we can support. This depends on
knowing our Virtual Function Resources and may be called a second time
if we fall back from MSI-X to MSI Interrupt Mode. This change fixes that
problem.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids a race condition where a system that has network devices set up
to be automatically configured and we get the first Port Link Status
message from the firmware on the Asynchronous Firmware Event Queue before
we've enabled interrupts. If that happens, we end up losing the interrupt
and never realizing that the links has actually come up.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function t4vf_wait_dev_ready() is already called in t4vf_prep_adapter(),
no need to call it again in adap_init0().
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds a new function t4vf_fl_pkt_align() and use the same in SGE
initialization code to find out freelist packet alignment
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T4 and T5 hardware will not coalesce Free List PCI-E Fetch Requests if
the Host Driver provides more Free List Pointers than the Fetch Burst
Minimum value.  So if we set FBMIN to 64 bytes and the Host Driver
supplies 128 bytes of Free List Pointer data, the hardware will issue two
64-byte PCI-E Fetch Requests rather than a single coallesced 128-byte
Fetch Request. T6 fixes this. So, for T4/T5 we set the FBMIN value to 128
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use freelist capacity instead of freelist size while checking, if
freelist needs to be refilled
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.

In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The vpd strings are left justified, in a fixed length array, with possible
trailing white space and no NUL.  So fix them up before calling kstrto*().

This is a recent regression which causes cxgb3 to fail to load.

Fixes: e72c932d ("cxgb3: Convert simple_strtoul to kstrtox")
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.

In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 115b56af ("cxgb4: Update mps_tcam output to include T6
fields") from Dec 23, 2015, leads to the following static checker
warning:

        drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:1735
mps_tcam_show()
        warn: we tested 'lookup_type' before and it was 'true'

Fixing it.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cphy_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since t4_alloc_mem can be failed in memory pressure,
if not properly handled, NULL dereference could be happened.
Signed-off-by: NInsu Yun <wuninsu@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove deprecated module parameters, and mark one parameter as
deprecated.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CLIP is always enabled and hardware uses 2 TID entries instead of 4 for
IPv6 in CLIP mode.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>