The i2c failures were caused by enabling both i2c gates
at the same time while putting the tuners asleep.

This patch removes the init() and sleep() callbacks from the tuner,
to prevent frontend.c from calling
  i2c_gate_ctrl
  tuner init / sleep
  i2c_gate_ctrl
without holding the lock.
tuner init() and sleep() are instead called in frontend init() and
sleep().
Signed-off-by: NGordon Hecker <ghecker@gmx.de>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Reported by kmemleak.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

struct dvb_usb_device *d can never be NULL so don't waste time
checking for this.

Rationale: the urb's context is set when usb_fill_bulk_urb() is called
in dib0700_rc_setup(), and never changes after that. d is dereferenced
unconditionally in dib0700_rc_setup() so it can't be NULL or the
driver would crash right away.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Support for m88rs2000 module.

The driver also attempts to overcome occasional lock problems.

Call backs are now used for read_status, signal level and SNR.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

These were in the original lme2510 device driver.

Removing them significantly speeds up the driver.

All tuners tested.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch add CI support to az6007 driver.
Signed-off-by: NJose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove delays added for STV0288 frontend.

This patch significantly speeds up channel change and scan.

It requires patch 10161-STV0288 increase delay between carrier search.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Besides sticks with the usb id 14AA:0160, there exists also some
with 14AA:0161 - this is the output in /var/log/messages:

usb 1-1: new high-speed USB device number 2 using ehci_hcd
usb 1-1: New USB device found, idVendor=14aa, idProduct=0161
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: Freecom DVB-T
usb 1-1: Manufacturer: Freecom DVB-T
usb 1-1: SerialNumber: 00000000000036742

The patch is based on the code at
http://git.linuxtv.org/anttip/media_tree.git/shortlog/refs/heads/realtekSigned-off-by: NPaolo Pantò <munix9@googlemail.com>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
  cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Read signal strength using VAR_P_INBAND and apply FEC preferred values.

Note this does not work on IT9137 devices even with dvb-usb-it9135-01.fw
firmware.

Config read_sl allows switch between read signal strength and signal
level.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Allow PID 8192 to turn PID filter off in USB high speed.

The PID number is still written to the PID index and will only
turn on again if that index is set to 0.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some virtual I2C commands are missed along some PID filtering
commands resulting complete stall of driver.

Since dvb-usb cannot handle the -EAGAIN error and commands
generally should not be missed mutex_lock is used instead.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hardware is not accessible when device is sleeping.
Preventing such IOCTLs when sleep should be job of DVB CORE...
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

* some style issues
* remove rtl2832u device IDs
* move USB IDs to correct place
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is almost perfect now!
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Do not return error for demod attach in case of mxl5005s tuner.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For now it supports only Realtek RTL2831U chip.
RTL2831U is integrated DVB USB interface and DVB-T demod.
DVB-T demod integrated to RTL2831U is Realtek RTL2830.
Supported tuners are QT1010, MT2060 and MXL5005S.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
[mchehab@redhat.com: fix a small typo]
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Problems with the PID setting stalling demux on applications like VDR and MythTV.

The PID filter is now defaulted to OFF.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Support for different types of remote.

ITE remotes share common device IDs with differently assigned keys.

Two versions of remote maps have been created there are likely to be more.
v1 for all other IDs
v2 for USB_PID_ITETECH_IT9135_9005.

This patch also separates the configuration parts from it913x_identify_state function.

TODO
remotes for HID interfaces.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some version 2 devices have different tuner IDs. ID 0x38
appears to have weak signal strength.

Apply default 0x60 to unknown IDs.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Correct spelling "reseting" to "resetting" in
drivers/media/dvb/dvb-usb/lmedm04.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Control message load increased heavily after CI/CAM support due
to dvb_ca_en50221. It looks like CI/CAM drops to non-working
state easily after error is returned to its callbacks. Due to
that, add some logic to avoid errors repeating failed messages.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changeset 7830bbaf mangled the bandwidth field for CinergyT2.
Properly fill it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

No more error that error seen when device is plugged:
dvb_ca adapter 0: Invalid PC card inserted :(
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix bug introduced by multi-frontend to single-frontend change.
This parameter is no longer used after multi-frontend to single-frontend change.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As recommended by Jason at ITE, the chip version should select firmware.

However, to continue to support IT9137 firmware with different configuration
the driver will use udev->descriptor.idVendor to select the difference
between IT9135 and IT9137.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changeset 7830bbaf mangled the bandwidth field for CinergyT2.
Properly fill it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the corresponding entries to allow building this driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of using a fake keycode, just for testing, use the
right one, for Terratec H7.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

USB data transfers may not work if the buffer is allocated at
the stack. Be sure to use kmalloc on all places where a buffer
is needed.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This will avoid interference with CI and IR I/O operations.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove commented test code, remove unused poweroff stuff, and
fix the copyright data.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Several changes were needed to make az6007 to work, producing
the same commands as the original driver. This patch does
that.

While here, be less verbose when debug is not enabled.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>