stable inclusion
from linux-4.19.232
commit 28ca082153794cf5c98e7bb93d7f30f8ba46bec4

--------------------------------

commit 737b0ef3 upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.

This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.

Fixes: e1eaea46 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-1-daniel.starke@siemens.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.232
commit 400c2f361c25bc092d0636cfa32d0549a181e653

--------------------------------

commit e386dfc5 upstream.

Commit 054aa8d4 ("fget: check that the fd still exists after getting
a ref to it") fixed a race with getting a reference to a file just as it
was being closed.  It was a fairly minimal patch, and I didn't think
re-checking the file pointer lookup would be a measurable overhead,
since it was all right there and cached.

But I was wrong, as pointed out by the kernel test robot.

The 'poll2' case of the will-it-scale.per_thread_ops benchmark regressed
quite noticeably.  Admittedly it seems to be a very artificial test:
doing "poll()" system calls on regular files in a very tight loop in
multiple threads.

That means that basically all the time is spent just looking up file
descriptors without ever doing anything useful with them (not that doing
'poll()' on a regular file is useful to begin with).  And as a result it
shows the extra "re-check fd" cost as a sore thumb.

Happily, the regression is fixable by just writing the code to loook up
the fd to be better and clearer.  There's still a cost to verify the
file pointer, but now it's basically in the noise even for that
benchmark that does nothing else - and the code is more understandable
and has better comments too.

[ Side note: this patch is also a classic case of one that looks very
  messy with the default greedy Myers diff - it's much more legible with
  either the patience of histogram diff algorithm ]

Link: https://lore.kernel.org/lkml/20211210053743.GA36420@xsang-OptiPlex-9020/
Link: https://lore.kernel.org/lkml/20211213083154.GA20853@linux.intel.com/Reported-by: Nkernel test robot <oliver.sang@intel.com>
Tested-by: NCarel Si <beibei.si@intel.com>
Cc: Jann Horn <jannh@google.com>
Cc: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NBaokun Li <libaokun1@huawei.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.232
commit a6fcced73d15ab57cd97813999edf6f19d3032f8

--------------------------------

commit c94afc46 upstream.

memblock.{reserved,memory}.regions may be allocated using kmalloc() in
memblock_double_array(). Use kfree() to release these kmalloced regions
indicated by memblock_{reserved,memory}_in_slab.
Signed-off-by: NMiaohe Lin <linmiaohe@huawei.com>
Fixes: 3010f876 ("mm: discard memblock data later")
Signed-off-by: NMike Rapoport <rppt@linux.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.232
commit 337e49675ce55c23a50b92aae889ec5d910d6dc7

--------------------------------

commit e3b7468f upstream.

Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.

This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.

Fixes: e1eaea46 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-3-daniel.starke@siemens.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.232
commit e9ffbe63f6f32f526a461756309b61c395168d73

--------------------------------

commit cc20cced upstream.

We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
 -> ipip encap -> net_failover tx -> virtio_net tx

When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.

Call Trace:
 tcp4_gso_segment        ------> return NULL
 inet_gso_segment        ------> inner iph, network_header points to
 ipip_gso_segment
 inet_gso_segment        ------> outer iph
 skb_mac_gso_segment

Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.

Call Trace:
 inet_gso_segment        ------> inner iph, outer iph is skipped
 skb_mac_gso_segment
 __skb_gso_segment
 validate_xmit_skb
 validate_xmit_skb_list
 sch_direct_xmit
 __qdisc_run
 __dev_queue_xmit        ------> virtio_net
 dev_hard_start_xmit
 __dev_queue_xmit        ------> net_failover
 ip_finish_output2
 ip_output
 iptunnel_xmit
 ip_tunnel_xmit
 ipip_tunnel_xmit        ------> ipip
 dev_hard_start_xmit
 __dev_queue_xmit
 ip_finish_output2
 ip_output
 ip_forward
 ip_rcv
 __netif_receive_skb_one_core
 netif_receive_skb_internal
 napi_gro_receive
 receive_buf
 virtnet_poll
 net_rx_action

The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.

This patch also includes ipv6_gso_segment(), considering SIT, etc.

Fixes: cb32f511 ("ipip: add GSO/TSO support")
Signed-off-by: NTao Liu <thomas.liu@ucloud.cn>
Reviewed-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.232
commit 1f4ae0f158dafa74133108bfa07b8053eb2a7898

--------------------------------

commit ef527f96 upstream.

Whenever one of these functions pull all data from an skb in a frag_list,
use consume_skb() instead of kfree_skb() to avoid polluting drop
monitoring.

Fixes: 6fa01ccd ("skbuff: Add pskb_extract() helper function")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220220154052.1308469-1-eric.dumazet@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.232
commit 4eec5fe1c680a6c47a9bc0cde00960a4eb663342

--------------------------------

commit 05c7b7a9 upstream.

As previously discussed(https://lkml.org/lkml/2022/1/20/51),
cpuset_attach() is affected with similar cpu hotplug race,
as follow scenario:

     cpuset_attach()				cpu hotplug
    ---------------------------            ----------------------
    down_write(cpuset_rwsem)
    guarantee_online_cpus() // (load cpus_attach)
					sched_cpu_deactivate
					  set_cpu_active()
					  // will change cpu_active_mask
    set_cpus_allowed_ptr(cpus_attach)
      __set_cpus_allowed_ptr_locked()
       // (if the intersection of cpus_attach and
         cpu_active_mask is empty, will return -EINVAL)
    up_write(cpuset_rwsem)

To avoid races such as described above, protect cpuset_attach() call
with cpu_hotplug_lock.

Fixes: be367d09 ("cgroups: let ss->can_attach and ss->attach do whole threadgroups at a time")
Cc: stable@vger.kernel.org # v2.6.32+
Reported-by: NZhao Gongyi <zhaogongyi@huawei.com>
Signed-off-by: NZhang Qiao <zhangqiao22@huawei.com>
Acked-by: NWaiman Long <longman@redhat.com>
Reviewed-by: NMichal Koutný <mkoutny@suse.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit 8f8c9e71e192823e4d76fdc53b4391642291bafc

--------------------------------

[ Upstream commit 3203ce39 ]

The kernel parameter "tp_printk_stop_on_boot" starts with "tp_printk" which is
the same as another kernel parameter "tp_printk". If "tp_printk" setup is
called before the "tp_printk_stop_on_boot", it will override the latter
and keep it from being set.

This is similar to other kernel parameter issues, such as:
  Commit 745a600c ("um: console: Ignore console= option")
or init/do_mounts.c:45 (setup function of "ro" kernel param)

Fix it by checking for a "_" right after the "tp_printk" and if that
exists do not process the parameter.

Link: https://lkml.kernel.org/r/20220208195421.969326-1-jsyoo5b@gmail.comSigned-off-by: NJaeSang Yoo <jsyoo5b@gmail.com>
[ Fixed up change log and added space after if condition ]
Signed-off-by: NSteven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit 783d70c94e513ca715643c00c6c275d9eb3b1a9e

--------------------------------

commit 2d21543e upstream.

Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.

Fixes: dc312349 ("dmaengine: rcar-dmac: Widen DMA mask to 40 bits")
Signed-off-by: NJiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220106030939.2644320-1-jiasheng@iscas.ac.cnSigned-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit f63c9fa36bd7548fd07792127057cccb68a7e274

--------------------------------

commit 5740d068 upstream.

We have been living dangerously, at the mercy of malicious users,
abusing TC_ACT_REPEAT, as shown by this syzpot report [1].

Add an arbitrary limit (32) to the number of times an action can
return TC_ACT_REPEAT.

v2: switch the limit to 32 instead of 10.
    Use net_warn_ratelimited() instead of pr_err_once().

[1] (C repro available on demand)

rcu: INFO: rcu_preempt self-detected stall on CPU
rcu:    1-...!: (10500 ticks this GP) idle=021/1/0x4000000000000000 softirq=5592/5592 fqs=0
        (t=10502 jiffies g=5305 q=190)
rcu: rcu_preempt kthread timer wakeup didn't happen for 10502 jiffies! g5305 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
rcu:    Possible timer handling issue on cpu=0 timer-softirq=3527
rcu: rcu_preempt kthread starved for 10505 jiffies! g5305 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0
rcu:    Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt     state:I stack:29344 pid:   14 ppid:     2 flags:0x00004000
Call Trace:
 <TASK>
 context_switch kernel/sched/core.c:4986 [inline]
 __schedule+0xab2/0x4db0 kernel/sched/core.c:6295
 schedule+0xd2/0x260 kernel/sched/core.c:6368
 schedule_timeout+0x14a/0x2a0 kernel/time/timer.c:1881
 rcu_gp_fqs_loop+0x186/0x810 kernel/rcu/tree.c:1963
 rcu_gp_kthread+0x1de/0x320 kernel/rcu/tree.c:2136
 kthread+0x2e9/0x3a0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
 </TASK>
rcu: Stack dump where RCU GP kthread last ran:
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
CPU: 0 PID: 3646 Comm: syz-executor358 Not tainted 5.17.0-rc3-syzkaller-00149-gbf8e59fd #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:rep_nop arch/x86/include/asm/vdso/processor.h:13 [inline]
RIP: 0010:cpu_relax arch/x86/include/asm/vdso/processor.h:18 [inline]
RIP: 0010:pv_wait_head_or_lock kernel/locking/qspinlock_paravirt.h:437 [inline]
RIP: 0010:__pv_queued_spin_lock_slowpath+0x3b8/0xb40 kernel/locking/qspinlock.c:508
Code: 48 89 eb c6 45 01 01 41 bc 00 80 00 00 48 c1 e9 03 83 e3 07 41 be 01 00 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8d 2c 01 eb 0c <f3> 90 41 83 ec 01 0f 84 72 04 00 00 41 0f b6 45 00 38 d8 7f 08 84
RSP: 0018:ffffc9000283f1b0 EFLAGS: 00000206
RAX: 0000000000000003 RBX: 0000000000000000 RCX: 1ffff1100fc0071e
RDX: 0000000000000001 RSI: 0000000000000201 RDI: 0000000000000000
RBP: ffff88807e0038f0 R08: 0000000000000001 R09: ffffffff8ffbf9ff
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000004c1e
R13: ffffed100fc0071e R14: 0000000000000001 R15: ffff8880b9c3aa80
FS:  00005555562bf300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffdbfef12b8 CR3: 00000000723c2000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 pv_queued_spin_lock_slowpath arch/x86/include/asm/paravirt.h:591 [inline]
 queued_spin_lock_slowpath arch/x86/include/asm/qspinlock.h:51 [inline]
 queued_spin_lock include/asm-generic/qspinlock.h:85 [inline]
 do_raw_spin_lock+0x200/0x2b0 kernel/locking/spinlock_debug.c:115
 spin_lock_bh include/linux/spinlock.h:354 [inline]
 sch_tree_lock include/net/sch_generic.h:610 [inline]
 sch_tree_lock include/net/sch_generic.h:605 [inline]
 prio_tune+0x3b9/0xb50 net/sched/sch_prio.c:211
 prio_init+0x5c/0x80 net/sched/sch_prio.c:244
 qdisc_create.constprop.0+0x44a/0x10f0 net/sched/sch_api.c:1253
 tc_modify_qdisc+0x4c5/0x1980 net/sched/sch_api.c:1660
 rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5594
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x539/0x7e0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:725
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2413
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2496
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f7ee98aae99
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 41 15 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffdbfef12d8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007ffdbfef1300 RCX: 00007f7ee98aae99
RDX: 0000000000000000 RSI: 0000000020000000 RDI: 0000000000000003
RBP: 0000000000000000 R08: 000000000000000d R09: 000000000000000d
R10: 000000000000000d R11: 0000000000000246 R12: 00007ffdbfef12f0
R13: 00000000000f4240 R14: 000000000004ca47 R15: 00007ffdbfef12e4
 </TASK>
INFO: NMI handler (nmi_cpu_backtrace_handler) took too long to run: 2.293 msecs
NMI backtrace for cpu 1
CPU: 1 PID: 3260 Comm: kworker/1:3 Not tainted 5.17.0-rc3-syzkaller-00149-gbf8e59fd #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: mld mld_ifc_work
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
 nmi_cpu_backtrace.cold+0x47/0x144 lib/nmi_backtrace.c:111
 nmi_trigger_cpumask_backtrace+0x1b3/0x230 lib/nmi_backtrace.c:62
 trigger_single_cpu_backtrace include/linux/nmi.h:164 [inline]
 rcu_dump_cpu_stacks+0x25e/0x3f0 kernel/rcu/tree_stall.h:343
 print_cpu_stall kernel/rcu/tree_stall.h:604 [inline]
 check_cpu_stall kernel/rcu/tree_stall.h:688 [inline]
 rcu_pending kernel/rcu/tree.c:3919 [inline]
 rcu_sched_clock_irq.cold+0x5c/0x759 kernel/rcu/tree.c:2617
 update_process_times+0x16d/0x200 kernel/time/timer.c:1785
 tick_sched_handle+0x9b/0x180 kernel/time/tick-sched.c:226
 tick_sched_timer+0x1b0/0x2d0 kernel/time/tick-sched.c:1428
 __run_hrtimer kernel/time/hrtimer.c:1685 [inline]
 __hrtimer_run_queues+0x1c0/0xe50 kernel/time/hrtimer.c:1749
 hrtimer_interrupt+0x31c/0x790 kernel/time/hrtimer.c:1811
 local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1086 [inline]
 __sysvec_apic_timer_interrupt+0x146/0x530 arch/x86/kernel/apic/apic.c:1103
 sysvec_apic_timer_interrupt+0x8e/0xc0 arch/x86/kernel/apic/apic.c:1097
 </IRQ>
 <TASK>
 asm_sysvec_apic_timer_interrupt+0x12/0x20 arch/x86/include/asm/idtentry.h:638
RIP: 0010:__sanitizer_cov_trace_const_cmp4+0xc/0x70 kernel/kcov.c:286
Code: 00 00 00 48 89 7c 30 e8 48 89 4c 30 f0 4c 89 54 d8 20 48 89 10 5b c3 0f 1f 80 00 00 00 00 41 89 f8 bf 03 00 00 00 4c 8b 14 24 <89> f1 65 48 8b 34 25 00 70 02 00 e8 14 f9 ff ff 84 c0 74 4b 48 8b
RSP: 0018:ffffc90002c5eea8 EFLAGS: 00000246
RAX: 0000000000000007 RBX: ffff88801c625800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003
RBP: ffff8880137d3100 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff874fcd88 R11: 0000000000000000 R12: ffff88801d692dc0
R13: ffff8880137d3104 R14: 0000000000000000 R15: ffff88801d692de8
 tcf_police_act+0x358/0x11d0 net/sched/act_police.c:256
 tcf_action_exec net/sched/act_api.c:1049 [inline]
 tcf_action_exec+0x1a6/0x530 net/sched/act_api.c:1026
 tcf_exts_exec include/net/pkt_cls.h:326 [inline]
 route4_classify+0xef0/0x1400 net/sched/cls_route.c:179
 __tcf_classify net/sched/cls_api.c:1549 [inline]
 tcf_classify+0x3e8/0x9d0 net/sched/cls_api.c:1615
 prio_classify net/sched/sch_prio.c:42 [inline]
 prio_enqueue+0x3a7/0x790 net/sched/sch_prio.c:75
 dev_qdisc_enqueue+0x40/0x300 net/core/dev.c:3668
 __dev_xmit_skb net/core/dev.c:3756 [inline]
 __dev_queue_xmit+0x1f61/0x3660 net/core/dev.c:4081
 neigh_hh_output include/net/neighbour.h:533 [inline]
 neigh_output include/net/neighbour.h:547 [inline]
 ip_finish_output2+0x14dc/0x2170 net/ipv4/ip_output.c:228
 __ip_finish_output net/ipv4/ip_output.c:306 [inline]
 __ip_finish_output+0x396/0x650 net/ipv4/ip_output.c:288
 ip_finish_output+0x32/0x200 net/ipv4/ip_output.c:316
 NF_HOOK_COND include/linux/netfilter.h:296 [inline]
 ip_output+0x196/0x310 net/ipv4/ip_output.c:430
 dst_output include/net/dst.h:451 [inline]
 ip_local_out+0xaf/0x1a0 net/ipv4/ip_output.c:126
 iptunnel_xmit+0x628/0xa50 net/ipv4/ip_tunnel_core.c:82
 geneve_xmit_skb drivers/net/geneve.c:966 [inline]
 geneve_xmit+0x10c8/0x3530 drivers/net/geneve.c:1077
 __netdev_start_xmit include/linux/netdevice.h:4683 [inline]
 netdev_start_xmit include/linux/netdevice.h:4697 [inline]
 xmit_one net/core/dev.c:3473 [inline]
 dev_hard_start_xmit+0x1eb/0x920 net/core/dev.c:3489
 __dev_queue_xmit+0x2985/0x3660 net/core/dev.c:4116
 neigh_hh_output include/net/neighbour.h:533 [inline]
 neigh_output include/net/neighbour.h:547 [inline]
 ip6_finish_output2+0xf7a/0x14f0 net/ipv6/ip6_output.c:126
 __ip6_finish_output net/ipv6/ip6_output.c:191 [inline]
 __ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170
 ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201
 NF_HOOK_COND include/linux/netfilter.h:296 [inline]
 ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224
 dst_output include/net/dst.h:451 [inline]
 NF_HOOK include/linux/netfilter.h:307 [inline]
 NF_HOOK include/linux/netfilter.h:301 [inline]
 mld_sendpack+0x9a3/0xe40 net/ipv6/mcast.c:1826
 mld_send_cr net/ipv6/mcast.c:2127 [inline]
 mld_ifc_work+0x71c/0xdc0 net/ipv6/mcast.c:2659
 process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307
 worker_thread+0x657/0x1110 kernel/workqueue.c:2454
 kthread+0x2e9/0x3a0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
 </TASK>
----------------
Code disassembly (best guess):
   0:   48 89 eb                mov    %rbp,%rbx
   3:   c6 45 01 01             movb   $0x1,0x1(%rbp)
   7:   41 bc 00 80 00 00       mov    $0x8000,%r12d
   d:   48 c1 e9 03             shr    $0x3,%rcx
  11:   83 e3 07                and    $0x7,%ebx
  14:   41 be 01 00 00 00       mov    $0x1,%r14d
  1a:   48 b8 00 00 00 00 00    movabs $0xdffffc0000000000,%rax
  21:   fc ff df
  24:   4c 8d 2c 01             lea    (%rcx,%rax,1),%r13
  28:   eb 0c                   jmp    0x36
* 2a:   f3 90                   pause <-- trapping instruction
  2c:   41 83 ec 01             sub    $0x1,%r12d
  30:   0f 84 72 04 00 00       je     0x4a8
  36:   41 0f b6 45 00          movzbl 0x0(%r13),%eax
  3b:   38 d8                   cmp    %bl,%al
  3d:   7f 08                   jg     0x47
  3f:   84                      .byte 0x84

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220215235305.3272331-1-eric.dumazet@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit 891484112f4ffd0b576e88407bbd3653abf3faba

--------------------------------

commit 5c23b3f9 upstream.

Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.

This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.

If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is

qcom_nandc_unalloc(nandc);

clk_disable_unprepare(nandc->aon_clk);
clk_disable_unprepare(nandc->core_clk);

dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res),
		   DMA_BIDIRECTIONAL, 0);

Tweaking probe() to both bring up and tear-down in that order removes the
reset if we end up deferring elsewhere.

Fixes: c76b78d8 ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: NBryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: NManivannan Sadhasivam <mani@kernel.org>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit d2ba21f271eb167ac2b0581598e55222b89f0f32

--------------------------------

commit d19e0183 upstream.

The result of the writeback, whether it is an ENOSPC or an EIO, or
anything else, does not inhibit the NFS client from reporting the
correct file timestamps.

Fixes: 79566ef0 ("NFS: Getattr doesn't require data sync semantics")
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit 67552482aee7a139ed957595db8668d28ddc2c42

--------------------------------

commit e0caaf75 upstream.

Commit ac795161 (NFSv4: Handle case where the lookup of a directory
fails) [1], part of Linux since 5.17-rc2, introduced a regression, where
a symbolic link on an NFS mount to a directory on another NFS does not
resolve(?) the first time it is accessed:
Reported-by: NPaul Menzel <pmenzel@molgen.mpg.de>
Fixes: ac795161 ("NFSv4: Handle case where the lookup of a directory fails")
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: NDonald Buczek <buczek@molgen.mpg.de>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit 4218e6995c19970aa7b32914be6c8e059837cbdf

--------------------------------

commit 9ceaf6f7 upstream.

syzbot reported that two threads might write over agg_select_timer
at the same time. Make agg_select_timer atomic to fix the races.

BUG: KCSAN: data-race in bond_3ad_initiate_agg_selection / bond_3ad_state_machine_handler

read to 0xffff8881242aea90 of 4 bytes by task 1846 on cpu 1:
 bond_3ad_state_machine_handler+0x99/0x2810 drivers/net/bonding/bond_3ad.c:2317
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x1bf/0x1e0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30

write to 0xffff8881242aea90 of 4 bytes by task 25910 on cpu 0:
 bond_3ad_initiate_agg_selection+0x18/0x30 drivers/net/bonding/bond_3ad.c:1998
 bond_open+0x658/0x6f0 drivers/net/bonding/bond_main.c:3967
 __dev_open+0x274/0x3a0 net/core/dev.c:1407
 dev_open+0x54/0x190 net/core/dev.c:1443
 bond_enslave+0xcef/0x3000 drivers/net/bonding/bond_main.c:1937
 do_set_master net/core/rtnetlink.c:2532 [inline]
 do_setlink+0x94f/0x2500 net/core/rtnetlink.c:2736
 __rtnl_newlink net/core/rtnetlink.c:3414 [inline]
 rtnl_newlink+0xfeb/0x13e0 net/core/rtnetlink.c:3529
 rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5594
 netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2494
 rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5612
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x602/0x6d0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x728/0x850 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmsg+0x195/0x230 net/socket.c:2496
 __do_sys_sendmsg net/socket.c:2505 [inline]
 __se_sys_sendmsg net/socket.c:2503 [inline]
 __x64_sys_sendmsg+0x42/0x50 net/socket.c:2503
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x00000050 -> 0x0000004f

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 25910 Comm: syz-executor.1 Tainted: G        W         5.17.0-rc4-syzkaller-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit e294bc65746b779e4ad50f95ed04926cf72d1454

--------------------------------

commit dcd54265 upstream.

trace_napi_poll_hit() is reading stat->dev while another thread can write
on it from dropmon_net_event()

Use READ_ONCE()/WRITE_ONCE() here, RCU rules are properly enforced already,
we only have to take care of load/store tearing.

BUG: KCSAN: data-race in dropmon_net_event / trace_napi_poll_hit

write to 0xffff88816f3ab9c0 of 8 bytes by task 20260 on cpu 1:
 dropmon_net_event+0xb8/0x2b0 net/core/drop_monitor.c:1579
 notifier_call_chain kernel/notifier.c:84 [inline]
 raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:392
 call_netdevice_notifiers_info net/core/dev.c:1919 [inline]
 call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
 call_netdevice_notifiers net/core/dev.c:1945 [inline]
 unregister_netdevice_many+0x867/0xfb0 net/core/dev.c:10415
 ip_tunnel_delete_nets+0x24a/0x280 net/ipv4/ip_tunnel.c:1123
 vti_exit_batch_net+0x2a/0x30 net/ipv4/ip_vti.c:515
 ops_exit_list net/core/net_namespace.c:173 [inline]
 cleanup_net+0x4dc/0x8d0 net/core/net_namespace.c:597
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x1bf/0x1e0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30

read to 0xffff88816f3ab9c0 of 8 bytes by interrupt on cpu 0:
 trace_napi_poll_hit+0x89/0x1c0 net/core/drop_monitor.c:292
 trace_napi_poll include/trace/events/napi.h:14 [inline]
 __napi_poll+0x36b/0x3f0 net/core/dev.c:6366
 napi_poll net/core/dev.c:6432 [inline]
 net_rx_action+0x29e/0x650 net/core/dev.c:6519
 __do_softirq+0x158/0x2de kernel/softirq.c:558
 do_softirq+0xb1/0xf0 kernel/softirq.c:459
 __local_bh_enable_ip+0x68/0x70 kernel/softirq.c:383
 __raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
 _raw_spin_unlock_bh+0x33/0x40 kernel/locking/spinlock.c:210
 spin_unlock_bh include/linux/spinlock.h:394 [inline]
 ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
 wg_packet_decrypt_worker+0x73c/0x780 drivers/net/wireguard/receive.c:506
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x1bf/0x1e0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30

value changed: 0xffff88815883e000 -> 0x0000000000000000

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 26435 Comm: kworker/0:1 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: wg-crypt-wg2 wg_packet_decrypt_worker

Fixes: 4ea7e386 ("dropmon: add ability to detect when hardware dropsrxpackets")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit b0e55a57df7deed5f0682b584e4da913db2f6e84

--------------------------------

commit 35a79e64 upstream.

When 'ping' changes to use PING socket instead of RAW socket by:

   # sysctl -w net.ipv4.ping_group_range="0 100"

There is another regression caused when matching sk_bound_dev_if
and dif, RAW socket is using inet_iif() while PING socket lookup
is using skb->dev->ifindex, the cmd below fails due to this:

  # ip link add dummy0 type dummy
  # ip link set dummy0 up
  # ip addr add 192.168.111.1/24 dev dummy0
  # ping -I dummy0 192.168.111.1 -c1

The issue was also reported on:

  https://github.com/iputils/iputils/issues/104

But fixed in iputils in a wrong way by not binding to device when
destination IP is on device, and it will cause some of kselftests
to fail, as Jianlin noticed.

This patch is to use inet(6)_iif and inet(6)_sdif to get dif and
sdif for PING socket, and keep consistent with RAW socket.

Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: NJianlin Shi <jishi@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit c6055df602b9e9ed9427b7bb9088c75cb5cf6350

--------------------------------

commit 1b5a42d9 upstream.

In the function bacct_add_task the code reading task->exit_code was
introduced in commit f3cef7a9 ("[PATCH] csa: basic accounting over
taskstats"), and it is not entirely clear what the taskstats interface
is trying to return as only returning the exit_code of the first task
in a process doesn't make a lot of sense.

As best as I can figure the intent is to return task->exit_code after
a task exits.  The field is returned with per task fields, so the
exit_code of the entire process is not wanted.  Only the value of the
first task is returned so this is not a useful way to get the per task
ptrace stop code.  The ordinary case of returning this value is
returning after a task exits, which also precludes use for getting
a ptrace value.

It is common to for the first task of a process to also be the last
task of a process so this field may have done something reasonable by
accident in testing.

Make ac_exitcode a reliable per task value by always returning it for
every exited task.

Setting ac_exitcode in a sensible mannter makes it possible to continue
to provide this value going forward.

Cc: Balbir Singh <bsingharora@gmail.com>
Fixes: f3cef7a9 ("[PATCH] csa: basic accounting over taskstats")
Link: https://lkml.kernel.org/r/20220103213312.9144-5-ebiederm@xmission.comSigned-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
[sudip: adjust context]
Signed-off-by: NSudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit bbf7a1a2fc64d89896ba5eba494a40ca151a2675

--------------------------------

commit 23e7b1bf upstream.

Similar to commit 94e22389 ("xfrm4: strip ECN bits from tos field"),
clear the ECN bits from iph->tos when setting ->flowi4_tos.
This ensures that the last bit of ->flowi4_tos is cleared, so
ip_route_output_key_hash() isn't going to restrict the scope of the
route lookup.

Use ~INET_ECN_MASK instead of IPTOS_RT_MASK, because we have no reason
to clear the high order bits.

Found by code inspection, compile tested only.

Fixes: 4da3089f ("[IPSEC]: Use TOS when doing tunnel lookups")
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
[sudip: manually backport to previous location]
Signed-off-by: NSudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit a25e460fbb0340488d119fb2e28fe3f829b7417e

--------------------------------

[ Upstream commit 0fa0f99f ]

Unlike .queue_rq, in .submit_async_event drivers may not check the ctrl
readiness for AER submission. This may lead to a use-after-free
condition that was observed with nvme-tcp.

The race condition may happen in the following scenario:
1. driver executes its reset_ctrl_work
2. -> nvme_stop_ctrl - flushes ctrl async_event_work
3. ctrl sends AEN which is received by the host, which in turn
   schedules AEN handling
4. teardown admin queue (which releases the queue socket)
5. AEN processed, submits another AER, calling the driver to submit
6. driver attempts to send the cmd
==> use-after-free

In order to fix that, add ctrl state check to validate the ctrl
is actually able to accept the AER submission.

This addresses the above race in controller resets because the driver
during teardown should:
1. change ctrl state to RESETTING
2. flush async_event_work (as well as other async work elements)

So after 1,2, any other AER command will find the
ctrl state to be RESETTING and bail out without submitting the AER.
Signed-off-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit a1a41571f06e2b66229738bd0c92c1d57dd793e2

--------------------------------

[ Upstream commit dd5532a4 ]

Strangely, dquot_quota_sync ignores the return code from the ->sync_fs
call, which means that quotacalls like Q_SYNC never see the error.  This
doesn't seem right, so fix that.
Signed-off-by: NDarrick J. Wong <djwong@kernel.org>
Reviewed-by: NJan Kara <jack@suse.cz>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NChristian Brauner <brauner@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit d5c33270b8b2c274eb8df7b92d166166102528c6

--------------------------------

[ Upstream commit 2719c716 ]

If we fail to synchronize the filesystem while preparing to freeze the
fs, abort the freeze.
Signed-off-by: NDarrick J. Wong <djwong@kernel.org>
Reviewed-by: NJan Kara <jack@suse.cz>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NChristian Brauner <brauner@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.231
commit 592b1b5ad3ee6cce1381111cfd69c6dc868050a3

--------------------------------

commit 6e879367 upstream.

There is a build error when using a kernel .config file from
'kernel test robot' for a different build problem:

hppa64-linux-ld: drivers/tty/serial/8250/8250_gsc.o: in function `.LC3':
(.data.rel.ro+0x18): undefined reference to `iosapic_serial_irq'

when:
  CONFIG_GSC=y
  CONFIG_SERIO_GSCPS2=y
  CONFIG_SERIAL_8250_GSC=y
  CONFIG_PCI is not set
    and hence PCI_LBA is not set.
  IOSAPIC depends on PCI_LBA, so IOSAPIC is not set/enabled.

Make the use of iosapic_serial_irq() conditional to fix the build error.
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Reported-by: Nkernel test robot <lkp@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Suggested-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NHelge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 30d9f3cbe47e1018ddc8069ac5b5c9e66fbdf727

--------------------------------

commit 5f4e5ce6 upstream.

There's list corruption on cgrp_cpuctx_list. This happens on the
following path:

  perf_cgroup_switch: list_for_each_entry(cgrp_cpuctx_list)
      cpu_ctx_sched_in
         ctx_sched_in
            ctx_pinned_sched_in
              merge_sched_in
                  perf_cgroup_event_disable: remove the event from the list

Use list_for_each_entry_safe() to allow removing an entry during
iteration.

Fixes: 058fe1c0 ("perf/core: Make cgroup switch visit only cpuctxs with cgroup events")
Signed-off-by: NSong Liu <song@kernel.org>
Reviewed-by: NRik van Riel <riel@surriel.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220204004057.2961252-1-song@kernel.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 255264d81da6edaf4cd4fab836d1ef3ba09af6aa

--------------------------------

commit 495ac306 upstream.

If seccomp tries to kill a process, it should never see that process
again. To enforce this proactively, switch the mode to something
impossible. If encountered: WARN, reject all syscalls, and attempt to
kill the process again even harder.

Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Fixes: 8112c4f1 ("seccomp: remove 2-phase API")
Cc: stable@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 031ec2d7fabb5c01601490671666c55cf92e1b98

--------------------------------

commit c816b2e6 upstream.

The poll man page says POLLRDNORM is equivalent to POLLIN when used as
an event.
$ man poll
<snip>
              POLLRDNORM
                     Equivalent to POLLIN.

However, in n_tty driver, POLLRDNORM does not return until timeout even
if there is terminal input, whereas POLLIN returns.

The following test program works until kernel-3.17, but the test stops
in poll() after commit 57087d51 ("tty: Fix spurious poll() wakeups").

[Steps to run test program]
  $ cc -o test-pollrdnorm test-pollrdnorm.c
  $ ./test-pollrdnorm
  foo          <-- Type in something from the terminal followed by [RET].
                   The string should be echoed back.

  ------------------------< test-pollrdnorm.c >------------------------
  #include <stdio.h>
  #include <errno.h>
  #include <poll.h>
  #include <unistd.h>

  void main(void)
  {
	int		n;
	unsigned char	buf[8];
	struct pollfd	fds[1] = {{ 0, POLLRDNORM, 0 }};

	n = poll(fds, 1, -1);
	if (n < 0)
		perror("poll");
	n = read(0, buf, 8);
	if (n < 0)
		perror("read");
	if (n > 0)
		write(1, buf, n);
  }
  ------------------------------------------------------------------------

The attached patch fixes this problem.  Many calls to
wake_up_interruptible_poll() in the kernel source code already specify
"POLLIN | POLLRDNORM".

Fixes: 57087d51 ("tty: Fix spurious poll() wakeups")
Cc: stable@vger.kernel.org
Signed-off-by: NKosuke Tatsukawa <tatsu-ab1@nec.com>
Link: https://lore.kernel.org/r/TYCPR01MB81901C0F932203D30E452B3EA5209@TYCPR01MB8190.jpnprd01.prod.outlook.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 8f0ea3777590c16222d4251a49e31dd376ff5ac1

--------------------------------

[ Upstream commit 68468d8c ]

veth being NETIF_F_LLTX enabled, we need to be more careful
whenever we read/write rq->rx_notify_masked.

BUG: KCSAN: data-race in veth_xmit / veth_xmit

write to 0xffff888133d9a9f8 of 1 bytes by task 23552 on cpu 0:
 __veth_xdp_flush drivers/net/veth.c:269 [inline]
 veth_xmit+0x307/0x470 drivers/net/veth.c:350
 __netdev_start_xmit include/linux/netdevice.h:4683 [inline]
 netdev_start_xmit include/linux/netdevice.h:4697 [inline]
 xmit_one+0x105/0x2f0 net/core/dev.c:3473
 dev_hard_start_xmit net/core/dev.c:3489 [inline]
 __dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
 dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
 br_dev_queue_push_xmit+0x3ce/0x430 net/bridge/br_forward.c:53
 NF_HOOK include/linux/netfilter.h:307 [inline]
 br_forward_finish net/bridge/br_forward.c:66 [inline]
 NF_HOOK include/linux/netfilter.h:307 [inline]
 __br_forward+0x2e4/0x400 net/bridge/br_forward.c:115
 br_flood+0x521/0x5c0 net/bridge/br_forward.c:242
 br_dev_xmit+0x8b6/0x960
 __netdev_start_xmit include/linux/netdevice.h:4683 [inline]
 netdev_start_xmit include/linux/netdevice.h:4697 [inline]
 xmit_one+0x105/0x2f0 net/core/dev.c:3473
 dev_hard_start_xmit net/core/dev.c:3489 [inline]
 __dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
 dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
 neigh_hh_output include/net/neighbour.h:525 [inline]
 neigh_output include/net/neighbour.h:539 [inline]
 ip_finish_output2+0x6f8/0xb70 net/ipv4/ip_output.c:228
 ip_finish_output+0xfb/0x240 net/ipv4/ip_output.c:316
 NF_HOOK_COND include/linux/netfilter.h:296 [inline]
 ip_output+0xf3/0x1a0 net/ipv4/ip_output.c:430
 dst_output include/net/dst.h:451 [inline]
 ip_local_out net/ipv4/ip_output.c:126 [inline]
 ip_send_skb+0x6e/0xe0 net/ipv4/ip_output.c:1570
 udp_send_skb+0x641/0x880 net/ipv4/udp.c:967
 udp_sendmsg+0x12ea/0x14c0 net/ipv4/udp.c:1254
 inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff888133d9a9f8 of 1 bytes by task 23563 on cpu 1:
 __veth_xdp_flush drivers/net/veth.c:268 [inline]
 veth_xmit+0x2d6/0x470 drivers/net/veth.c:350
 __netdev_start_xmit include/linux/netdevice.h:4683 [inline]
 netdev_start_xmit include/linux/netdevice.h:4697 [inline]
 xmit_one+0x105/0x2f0 net/core/dev.c:3473
 dev_hard_start_xmit net/core/dev.c:3489 [inline]
 __dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
 dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
 br_dev_queue_push_xmit+0x3ce/0x430 net/bridge/br_forward.c:53
 NF_HOOK include/linux/netfilter.h:307 [inline]
 br_forward_finish net/bridge/br_forward.c:66 [inline]
 NF_HOOK include/linux/netfilter.h:307 [inline]
 __br_forward+0x2e4/0x400 net/bridge/br_forward.c:115
 br_flood+0x521/0x5c0 net/bridge/br_forward.c:242
 br_dev_xmit+0x8b6/0x960
 __netdev_start_xmit include/linux/netdevice.h:4683 [inline]
 netdev_start_xmit include/linux/netdevice.h:4697 [inline]
 xmit_one+0x105/0x2f0 net/core/dev.c:3473
 dev_hard_start_xmit net/core/dev.c:3489 [inline]
 __dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
 dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
 neigh_hh_output include/net/neighbour.h:525 [inline]
 neigh_output include/net/neighbour.h:539 [inline]
 ip_finish_output2+0x6f8/0xb70 net/ipv4/ip_output.c:228
 ip_finish_output+0xfb/0x240 net/ipv4/ip_output.c:316
 NF_HOOK_COND include/linux/netfilter.h:296 [inline]
 ip_output+0xf3/0x1a0 net/ipv4/ip_output.c:430
 dst_output include/net/dst.h:451 [inline]
 ip_local_out net/ipv4/ip_output.c:126 [inline]
 ip_send_skb+0x6e/0xe0 net/ipv4/ip_output.c:1570
 udp_send_skb+0x641/0x880 net/ipv4/udp.c:967
 udp_sendmsg+0x12ea/0x14c0 net/ipv4/udp.c:1254
 inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x00 -> 0x01

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 23563 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00064-gc36c04c2 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 948d4f21 ("veth: Add driver XDP")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 0be943916d781df2b652793bb2d3ae4f9624c10a

--------------------------------

[ Upstream commit 9eeabdf1 ]

When uncloning an skb dst and its associated metadata, a new
dst+metadata is allocated and later replaces the old one in the skb.
This is helpful to have a non-shared dst+metadata attached to a specific
skb.

The issue is the uncloned dst+metadata is initialized with a refcount of
1, which is increased to 2 before attaching it to the skb. When
tun_dst_unclone returns, the dst+metadata is only referenced from a
single place (the skb) while its refcount is 2. Its refcount will never
drop to 0 (when the skb is consumed), leading to a memory leak.

Fix this by removing the call to dst_hold in tun_dst_unclone, as the
dst+metadata refcount is already 1.

Fixes: fc4099f1 ("openvswitch: Fix egress tunnel info.")
Cc: Pravin B Shelar <pshelar@ovn.org>
Reported-by: NVlad Buslov <vladbu@nvidia.com>
Tested-by: NVlad Buslov <vladbu@nvidia.com>
Signed-off-by: NAntoine Tenart <atenart@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 040e92ea3d7d6f27c1b71d6502e35c54a0939cb7

--------------------------------

[ Upstream commit cfc56f85 ]

When uncloning an skb dst and its associated metadata a new dst+metadata
is allocated and the tunnel information from the old metadata is copied
over there.

The issue is the tunnel metadata has references to cached dst, which are
copied along the way. When a dst+metadata refcount drops to 0 the
metadata is freed including the cached dst entries. As they are also
referenced in the initial dst+metadata, this ends up in UaFs.

In practice the above did not happen because of another issue, the
dst+metadata was never freed because its refcount never dropped to 0
(this will be fixed in a subsequent patch).

Fix this by initializing the dst cache after copying the tunnel
information from the old metadata to also unshare the dst cache.

Fixes: d71785ff ("net: add dst_cache to ovs vxlan lwtunnel")
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: NVlad Buslov <vladbu@nvidia.com>
Tested-by: NVlad Buslov <vladbu@nvidia.com>
Signed-off-by: NAntoine Tenart <atenart@kernel.org>
Acked-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 12b6703e9546902c56b4b9048b893ad49d62bdd4

--------------------------------

[ Upstream commit 5611a006 ]

ip[6]mr_free_table() can only be called under RTNL lock.

RTNL: assertion failed at net/core/dev.c (10367)
WARNING: CPU: 1 PID: 5890 at net/core/dev.c:10367 unregister_netdevice_many+0x1246/0x1850 net/core/dev.c:10367
Modules linked in:
CPU: 1 PID: 5890 Comm: syz-executor.2 Not tainted 5.16.0-syzkaller-11627-g422ee58dc0ef #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:unregister_netdevice_many+0x1246/0x1850 net/core/dev.c:10367
Code: 0f 85 9b ee ff ff e8 69 07 4b fa ba 7f 28 00 00 48 c7 c6 00 90 ae 8a 48 c7 c7 40 90 ae 8a c6 05 6d b1 51 06 01 e8 8c 90 d8 01 <0f> 0b e9 70 ee ff ff e8 3e 07 4b fa 4c 89 e7 e8 86 2a 59 fa e9 ee
RSP: 0018:ffffc900046ff6e0 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff888050f51d00 RSI: ffffffff815fa008 RDI: fffff520008dfece
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815f3d6e R11: 0000000000000000 R12: 00000000fffffff4
R13: dffffc0000000000 R14: ffffc900046ff750 R15: ffff88807b7dc000
FS:  00007f4ab736e700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fee0b4f8990 CR3: 000000001e7d2000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 mroute_clean_tables+0x244/0xb40 net/ipv6/ip6mr.c:1509
 ip6mr_free_table net/ipv6/ip6mr.c:389 [inline]
 ip6mr_rules_init net/ipv6/ip6mr.c:246 [inline]
 ip6mr_net_init net/ipv6/ip6mr.c:1306 [inline]
 ip6mr_net_init+0x3f0/0x4e0 net/ipv6/ip6mr.c:1298
 ops_init+0xaf/0x470 net/core/net_namespace.c:140
 setup_net+0x54f/0xbb0 net/core/net_namespace.c:331
 copy_net_ns+0x318/0x760 net/core/net_namespace.c:475
 create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110
 copy_namespaces+0x391/0x450 kernel/nsproxy.c:178
 copy_process+0x2e0c/0x7300 kernel/fork.c:2167
 kernel_clone+0xe7/0xab0 kernel/fork.c:2555
 __do_sys_clone+0xc8/0x110 kernel/fork.c:2672
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f4ab89f9059
Code: Unable to access opcode bytes at RIP 0x7f4ab89f902f.
RSP: 002b:00007f4ab736e118 EFLAGS: 00000206 ORIG_RAX: 0000000000000038
RAX: ffffffffffffffda RBX: 00007f4ab8b0bf60 RCX: 00007f4ab89f9059
RDX: 0000000020000280 RSI: 0000000020000270 RDI: 0000000040200000
RBP: 00007f4ab8a5308d R08: 0000000020000300 R09: 0000000020000300
R10: 00000000200002c0 R11: 0000000000000206 R12: 0000000000000000
R13: 00007ffc3977cc1f R14: 00007f4ab736e300 R15: 0000000000022000
 </TASK>

Fixes: f243e5a7 ("ipmr,ip6mr: call ip6mr_free_table() on failure path")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Cong Wang <cong.wang@bytedance.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220208053451.2885398-1-eric.dumazet@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit c92b23d934f008aea3ec3239d951f6c4cc0c4422

--------------------------------

[ Upstream commit 23de0d7b ]

When 803.2ad mode enables a participating port, it should update
the slave-array. I have observed that the member links are participating
and are part of the active aggregator while the traffic is egressing via
only one member link (in a case where two links are participating). Via
kprobes I discovered that slave-arr has only one link added while
the other participating link wasn't part of the slave-arr.

I couldn't see what caused that situation but the simple code-walk
through provided me hints that the enable_port wasn't always associated
with the slave-array update.

Fixes: ee637714 ("bonding: Simplify the xmit function for modes that use xmit_hash")
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Acked-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 07e7f7cc619d15645e45d04b1c99550c6d292e9c

--------------------------------

commit 08389d88 upstream.

Add a kconfig knob which allows for unprivileged bpf to be disabled by default.
If set, the knob sets /proc/sys/kernel/unprivileged_bpf_disabled to value of 2.

This still allows a transition of 2 -> {0,1} through an admin. Similarly,
this also still keeps 1 -> {1} behavior intact, so that once set to permanently
disabled, it cannot be undone aside from a reboot.

We've also added extra2 with max of 2 for the procfs handler, so that an admin
still has a chance to toggle between 0 <-> 2.

Either way, as an additional alternative, applications can make use of CAP_BPF
that we added a while ago.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/74ec548079189e4e4dffaeb42b8987bb3c852eee.1620765074.git.daniel@iogearbox.net
[fllinden@amazon.com: backported to 4.19]
Signed-off-by: NFrank van der Linden <fllinden@amazon.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit ded80123b84253ecc6c6cfd1fbbbd99f51c984ec

--------------------------------

[ Upstream commit a861790a ]

iscsit_tpg_check_network_portal() has nested for_each loops and is supposed
to return true when a match is found. However, the tpg loop will still
continue after existing the tpg_np loop. If this tpg_np is not the last the
match value will be changed.

Break the outer loop after finding a match and make sure the np under each
tpg is unique.

Link: https://lore.kernel.org/r/20220111054742.19582-1-mingzhe.zou@easystack.cnSigned-off-by: NZouMingzhe <mingzhe.zou@easystack.cn>
Reviewed-by: NMike Christie <michael.christie@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 42dc3cf3174ec714732825638947e26923d9ea2a

--------------------------------

[ Upstream commit f5b27cc6 ]

Make nfs_parse_server_name available outside of nfs4namespace.c.
Signed-off-by: NOlga Kornievskaia <kolga@netapp.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 152f7db416c4bfcc8fc01e55cae60f63489580fa

--------------------------------

[ Upstream commit 90e12a31 ]

Remove the check for the zero length fs_locations reply in the
xdr decoding, and instead check for that in the migration code.
Signed-off-by: NOlga Kornievskaia <kolga@netapp.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit e6b0f9177c43ff9ad0f1a6dd3639c383373911b7

--------------------------------

[ Upstream commit b05bf5c6 ]

When decode_devicenotify_args() exits with no entries, we need to
ensure that the struct cb_devicenotifyargs is initialised to
{ 0, NULL } in order to avoid problems in
nfs4_callback_devicenotify().

Reported-by: <rtm@csail.mit.edu>
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 2c9587f72ff4b502c2fd15eb3ccff388eae12d07

--------------------------------

[ Upstream commit fbd2057e ]

kstrdup() returns NULL when some internal memory errors happen, it is
better to check the return value of it so to catch the memory error in
time.
Signed-off-by: NXiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 1789f59f1779c99d0756b40036c62a7519f53543

--------------------------------

[ Upstream commit 2c52c837 ]

When the bitmask of the attributes doesn't include the security label,
don't bother printing it. Since the label might not be null terminated,
adjust the printing format accordingly.
Signed-off-by: NOlga Kornievskaia <kolga@netapp.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 57e13bdd9634a48c0bdbf988858144350321c0bf

--------------------------------

commit 468d126d upstream.

For some long forgotten reason, the nfs_client cl_flags field is
initialised in nfs_get_client() instead of being initialised at
allocation time. This quirk was harmless until we moved the call to
nfs_create_rpc_client().

Fixes: dd99e9f9 ("NFSv4: Initialise connection to the server in nfs4_alloc_client()")
Cc: stable@vger.kernel.org # 4.8.x
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 4d9eb5b2ef21c496597f09355d9d6f5508731e98

--------------------------------

commit bb8e52e4 upstream.

Commit c2426d2a ("ima: added support for new kernel cmdline parameter
ima_template_fmt") introduced an additional check on the ima_template
variable to avoid multiple template selection.

Unfortunately, ima_template could be also set by the setup function of the
ima_hash= parameter, when it calls ima_template_desc_current(). This causes
attempts to choose a new template with ima_template= or with
ima_template_fmt=, after ima_hash=, to be ignored.

Achieve the goal of the commit mentioned with the new static variable
template_setup_done, so that template selection requests after ima_hash=
are not ignored.

Finally, call ima_init_template_list(), if not already done, to initialize
the list of templates before lookup_template_desc() is called.
Reported-by: NGuo Zihua <guozihua@huawei.com>
Signed-off-by: NRoberto Sassu <roberto.sassu@huawei.com>
Cc: stable@vger.kernel.org
Fixes: c2426d2a ("ima: added support for new kernel cmdline parameter ima_template_fmt")
Signed-off-by: NMimi Zohar <zohar@linux.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>

stable inclusion
from linux-4.19.230
commit 2c3beddb39ebe4411497629442f594133f29e0cd

--------------------------------

commit f7333b95 upstream.

The removal of ima_dir currently fails since ima_policy still exists, so
remove the ima_policy file before removing the directory.

Fixes: 4af4662f ("integrity: IMA policy")
Signed-off-by: NStefan Berger <stefanb@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Acked-by: NChristian Brauner <brauner@kernel.org>
Signed-off-by: NMimi Zohar <zohar@linux.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NYongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: NLaibin Qiu <qiulaibin@huawei.com>