Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 27 3月, 2020 1 次提交
    • L
      iwlwifi: move integrated, extra_phy and soc_latency to trans_cfg · 7897dfa2
      由 Luca Coelho 提交于 
      These values are selected based on the PCI device ID, so the decision
to use them can be made early.  By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean).  This will also allow us to make
more decisions based on, for instance, the SoC type in used.

The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.

Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
      7897dfa2
  3. 18 3月, 2020 1 次提交
  5. 04 1月, 2020 1 次提交
  7. 23 12月, 2019 3 次提交
    • L
      iwlwifi: remove CSR registers abstraction · 6dece0e9
      由 Luca Coelho 提交于 
      We needed this abstraction for some CSR registers for
IWL_DEVICE_22560, but that has been removed, so we don't need the
abstraction anymore.  Remove it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
      6dece0e9
    • L
      iwlwifi: remove some outdated iwl22000 configurations · b81b7bd0
      由 Luca Coelho 提交于 
      A few configuration structures were either not referenced anymore or
assigned to devices IDs that were not in use anymore.  Remove them.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
      b81b7bd0
    • J
      iwlwifi: allocate more receive buffers for HE devices · c042f0c7
      由 Johannes Berg 提交于 
      For HE-capable devices, we need to allocate more receive buffers as
there could be 256 frames aggregated into a single A-MPDU, and then
they might contain A-MSDUs as well. Until 22000 family, the devices
are able to put multiple frames into a single RB and the default RB
size is 4k, but starting from AX210 family this is no longer true.
On the other hand, those newer devices only use 2k receive buffers
(by default).

Modify the code and configuration to allocate an appropriate number
of RBs depending on the device capabilities:

 * 4096 for AX210 HE devices, which use 2k buffers by default,
 * 2048 for 22000 family devices which use 4k buffers by default,
 * 512 for existing 9000 family devices, which doesn't really
   change anything since that's the default before this patch,
 * 512 also for AX210/22000 family devices that don't do HE.

Theoretically, for devices lower than AX210, we wouldn't have to
allocate that many RBs if the RB size was manually increased, but
to support that the code got more complex, and it didn't really
seem necessary as that's a use case for monitor mode only, where
hopefully the wasted memory isn't really much of a concern.

Note that AX210 devices actually support bigger than 12-bit VID,
which is required here as we want to allocate 4096 buffers plus
some for quick recycling, so adjust the code for that as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
      c042f0c7
  9. 20 11月, 2019 1 次提交
  11. 15 11月, 2019 3 次提交
  13. 25 10月, 2019 1 次提交
  15. 06 9月, 2019 6 次提交
  17. 29 8月, 2019 1 次提交
  19. 16 7月, 2019 1 次提交
  21. 24 6月, 2019 3 次提交
  23. 29 4月, 2019 1 次提交
  25. 19 4月, 2019 2 次提交
  27. 18 4月, 2019 1 次提交
  29. 03 4月, 2019 4 次提交
  31. 22 3月, 2019 3 次提交
  33. 21 2月, 2019 1 次提交
  35. 14 2月, 2019 5 次提交
  37. 04 2月, 2019 1 次提交