The bnx2/bnx2x rings are made up of linked pages.  However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface.  In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE.  On archs with >= 64K PAGE_SIZE, it generates some compile
warnings.  Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For per device operations, cnic needs to dereference the RCU protected
cp->ulp_ops instead of the global cnic_ulp_tbl.  In 2 locations,
cnic_send_nlmsg() and cnic_copy_ulp_stats(), it was referencing the
global table.  If the device has been unregistered and these functions
are still being called (very unlikely scenarios), it could lead to NULL
pointer dereference.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit f280e89a (drivers: net: cpsw: fix for cpsw crash when build as modules)
moved cpts_register()/cpts_unregister() to  ndo_open()/ndo_stop(), but failed
to remove cpts_register in cpsw_probe() which leads to a double registration
and the following debug object splat.

[   18.991902] ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x2c
[   19.082249] [<c0059e80>] (init_timer_key) from [<c04965d4>] (cpts_register+0x1f0/0x2c4)
[   19.090642] [<c04965d4>] (cpts_register) from [<c04931dc>] (cpsw_ndo_open+0x780/0x81c)
[   19.098948] [<c04931dc>] (cpsw_ndo_open) from [<c0599c2c>] (__dev_open+0xb4/0x118)
Signed-off-by: NBenedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. For the 64 bits dma mask use dma_set_mask_and_coherent instead of
   dma_set_mask and dma_set_coherent_mask.

2. For the 32 bits dma mask dma_set_coherent_mask is only called if
   dma_set_mask fails, which is unusual. Assuming this as a bug, fixes
   it by replacing calls to dma_set_mask and dma_set_coherent_mask by a
   call to dma_set_mask_and_coherent.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Tested-by: NJonas Hahnfeld <hahnjo@hahnjo.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.

This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.

Successful tested on a i.MX28 board.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mlx4_en_stop_port() is called, we need to deregister also the
tunnel steering rules that relate to multicast.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When checking what protocol drivers to load, the IB driver should be
requested also over Ethernet ports, if the device supports IBoE (RoCE).

Fixes: b046ffe5 'net/mlx4_core: Load higher level modules according to ports type'
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the device mac address is changed, we must deregister the vxlan
steering rule associated with the previous mac, and register a new
steering rule using the new mac.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the value used to dump the vxlan offloads device capability to align
with the MLX4_DEV_CAP_FLAG2_yyy definition. While on that, add dump to
the IPoIB flow-steering device capability and fix small typo.

The vxlan cap value wasn't fully handled when a conflict was resolved
between MLX4_DEV_CAP_FLAG2_DMFS_IPOIB coming from the IB tree to
MLX4_DEV_CAP_FLAG2_VXLAN_OFFLOADS coming from net-next.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx descriptor version of RTL8111B belong to RTL_TD_0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.

Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

udelay() does not work on some architectures for values above
2000, in particular on ARM:

ERROR: "__bad_udelay" [drivers/net/ethernet/brocade/bna/bna.ko] undefined!
Reported-by: NVagrant Cascadian <vagrant@debian.org>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pci shutdown handler added in:

    bnx2: Add pci shutdown handler
    commit 25bfb1dd

created a shutdown down sequence without chip reset if the device was
never brought up.  This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive.  On some
systems, it may generate NMI in the bnx2's pci shutdown handler.

The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the PF call to pci_enable_sriov from the PF probe function
stalls for 10 seconds times the number of VFs probed on the host. This
happens because the way for such VFs to determine of the PF
initialization finished, is by attempting to issue reset on the
comm-channel and get timeout (after 10s).

The PF probe function is called from a kenernel workqueue, and therefore
during that time, rcu lock is being held and kernel's workqueue is
stalled. This blocks other processes that try to use the workqueue
or rcu lock.  For example, interface renaming which is calling
rcu_synchronize is blocked, and timedout by systemd.

Changed mlx4_init_slave() to allow VF probed on the host to immediatly
detect that the PF is not ready, and return EPROBE_DEFER instantly.

Only when the PF finishes the initialization, allow such VFs to
access the comm channel.

This issue and fix are relevant only for probed VFs on the hypervisor,
there is no way to pass this information to a VM until comm channel is
ready, so in a VM, if PF is not ready, the first command will be timedout
after 10 seconds and return EPROBE_DEFER.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a regression introduced by [1]. outbox was accessed instead of
outbox->buf. Typo was copy-pasted to [2] and [3].

[1] - cc1ade94 mlx4_core: Disable memory windows for virtual functions
[2] - 4de65803 mlx4_core: Add support for steerable IB UD QPs
[3] - 7ffdf726 net/mlx4_core: Add basic support for TCP/IP offloads under
      tunneling
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to load a MAC address into a u64 for passing to the
hypervisor via a register is broken on little endian.

Create a helper function called ibmveth_encode_mac_addr
which does the right thing in both big and little endian.

We were storing the MAC address in a long in struct ibmveth_adapter.
It's never used so remove it - we don't need another place in the
driver where we create endian issues with MAC addresses.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When allocating RX buffers a fixed size is used, while freeing is based
on actually received bytes, resulting in the following kernel warning
when CONFIG_DMA_API_DEBUG is enabled:
 WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1051 check_unmap+0x258/0x894()
 macb e000b000.ethernet: DMA-API: device driver frees DMA memory with different size [device address=0x000000002d170040] [map size=1536 bytes] [unmap size=60 bytes]
 Modules linked in:
 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.0-rc3-xilinx-00220-g49f84081ce4f #65
 [<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
 [<c0011df8>] (show_stack) from [<c03c775c>] (dump_stack+0x7c/0xc8)
 [<c03c775c>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
 [<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
 [<c0024670>] (warn_slowpath_fmt) from [<c0227d44>] (check_unmap+0x258/0x894)
 [<c0227d44>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
 [<c0228588>] (debug_dma_unmap_page) from [<c02ab78c>] (gem_rx+0x118/0x170)
 [<c02ab78c>] (gem_rx) from [<c02ac4d4>] (macb_poll+0x24/0x94)
 [<c02ac4d4>] (macb_poll) from [<c031222c>] (net_rx_action+0x6c/0x188)
 [<c031222c>] (net_rx_action) from [<c0028a28>] (__do_softirq+0x108/0x280)
 [<c0028a28>] (__do_softirq) from [<c0028e8c>] (irq_exit+0x84/0xf8)
 [<c0028e8c>] (irq_exit) from [<c000f360>] (handle_IRQ+0x68/0x8c)
 [<c000f360>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
 [<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
 Exception stack(0xc056df20 to 0xc056df68)
 df20: 00000001 c0577430 00000000 c0577430 04ce8e0d 00000002 edfce238 00000000
 df40: 04e20f78 00000002 c05981f4 00000000 00000008 c056df68 c0064008 c02d7658
 df60: 20000013 ffffffff
 [<c0012904>] (__irq_svc) from [<c02d7658>] (cpuidle_enter_state+0x54/0xf8)
 [<c02d7658>] (cpuidle_enter_state) from [<c02d77dc>] (cpuidle_idle_call+0xe0/0x138)
 [<c02d77dc>] (cpuidle_idle_call) from [<c000f660>] (arch_cpu_idle+0x8/0x3c)
 [<c000f660>] (arch_cpu_idle) from [<c006bec4>] (cpu_startup_entry+0xbc/0x124)
 [<c006bec4>] (cpu_startup_entry) from [<c053daec>] (start_kernel+0x350/0x3b0)
 ---[ end trace d5fdc38641bd3a11 ]---
 Mapped at:
  [<c0227184>] debug_dma_map_page+0x48/0x11c
  [<c02ab32c>] gem_rx_refill+0x154/0x1f8
  [<c02ac7b4>] macb_open+0x270/0x3e0
  [<c03152e0>] __dev_open+0x7c/0xfc
  [<c031554c>] __dev_change_flags+0x8c/0x140

Fixing this by passing the same size which is passed during mapping the
memory to the unmap function as well.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With CONFIG_DMA_API_DEBUG enabled the following warning is printed:
 WARNING: CPU: 0 PID: 619 at lib/dma-debug.c:1101 check_unmap+0x758/0x894()
 macb e000b000.ethernet: DMA-API: device driver failed to check map error[device address=0x000000002d171c02] [size=322 bytes] [mapped as single]
 Modules linked in:
 CPU: 0 PID: 619 Comm: udhcpc Not tainted 3.14.0-rc3-xilinx-00219-gd158fc7f #63
 [<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
 [<c0011df8>] (show_stack) from [<c03c7714>] (dump_stack+0x7c/0xc8)
 [<c03c7714>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
 [<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
 [<c0024670>] (warn_slowpath_fmt) from [<c0228244>] (check_unmap+0x758/0x894)
 [<c0228244>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
 [<c0228588>] (debug_dma_unmap_page) from [<c02aba64>] (macb_interrupt+0x1f8/0x2dc)
 [<c02aba64>] (macb_interrupt) from [<c006c6e4>] (handle_irq_event_percpu+0x2c/0x178)
 [<c006c6e4>] (handle_irq_event_percpu) from [<c006c86c>] (handle_irq_event+0x3c/0x5c)
 [<c006c86c>] (handle_irq_event) from [<c006f548>] (handle_fasteoi_irq+0xb8/0x100)
 [<c006f548>] (handle_fasteoi_irq) from [<c006c148>] (generic_handle_irq+0x20/0x30)
 [<c006c148>] (generic_handle_irq) from [<c000f35c>] (handle_IRQ+0x64/0x8c)
 [<c000f35c>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
 [<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
 Exception stack(0xed197f60 to 0xed197fa8)
 7f60: 00000134 60000013 bd94362e bd94362e be96b37c 00000014 fffffd72 00000122
 7f80: c000ebe4 ed196000 00000000 00000011 c032c0d8 ed197fa8 c0064008 c000ea20
 7fa0: 60000013 ffffffff
 [<c0012904>] (__irq_svc) from [<c000ea20>] (ret_fast_syscall+0x0/0x48)
 ---[ end trace 478f921d0d542d1e ]---
 Mapped at:
  [<c0227184>] debug_dma_map_page+0x48/0x11c
  [<c02aaca0>] macb_start_xmit+0x184/0x2a8
  [<c03143c0>] dev_hard_start_xmit+0x334/0x470
  [<c032c09c>] sch_direct_xmit+0x78/0x2f8
  [<c0314814>] __dev_queue_xmit+0x318/0x708

due to missing checks of the dma mapping. Add the appropriate checks to fix
this.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In kexec scenario, we failed to load the mlx4 driver in the
second kernel because the ownership bit was hold by the first
kernel without release correctly.

The patch adds shutdown() interface so that the ownership can
be released correctly in the first kernel. It also helps avoiding
EEH error happened during boot stage of the second kernel because
of undesired traffic, which can't be handled by hardware during
that stage on Power platform.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a CPDMA RX Descriptor leak that occurs after taking
the interface down when the CPSW is in Dual MAC mode. Previously
the CPSW_ALE port was left open up which causes packets to be received
and processed by the RX interrupt handler and were passed to the
non active network interface where they were ignored.

The fix is for the slave_stop function of the selected interface
to disable the respective CPSW_ALE Port from forwarding packets. This
blocks traffic from being received on the inactive interface.
Signed-off-by: NSchuyler Patton <spatton@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of TX workarounds in be_xmit_workarounds() routine
are not applicable (and result in HW errors) to Skyhawk-R chip.
Isolate BE3-R/Lancer specific workarounds to a separate routine.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_padto(), skb_share_check() and __vlan_put_tag() routines free
skb when they return an error. This patch fixes be_xmit_workarounds()
to not free skb again in such cases.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should clear promiscuous bits in adapter->flags while disabling promiscuous
mode. Else we will not put interface back into VLAN promisc mode if the vlans
already added exceeds the maximum limit.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.

Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ->tc_cfg[] array has QLC_DCB_MAX_TC (8) elements so the check is
off by one.  These functions are always called with valid values though
so it doesn't affect how the code works.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch b44_check_phy() was called when the phy called the
adjust callback. This method only change the mac duplex mode when the
carrier was off. When the phy changed the duplex mode after the carrier
was on the mac was not changed. This happened when an external phy was
used.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When support for external phys was added to b44, the calls to start and
stop the phy were missing in the mac driver. This adds the calls to
phy_start() and phy_stop().
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent commit "fe1624cf bna: RX Filter Enhancements" disables
VLAN tag stripping if the NIC is in promiscuous mode. This causes
__vlan_hwaccel_put_tag() is called when the stripping is disabled.
Because of this VLAN over bna does not work and causes BUGs in conjunction
with openvswitch like this:
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redefine the RXD_ERR_MASK to include only relevant error bits. This fixes
a customer reported issue of randomly dropping packets on the 5719.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c14db202 "bnx2x: Correct default Tx switching behaviour" supposedly
changed the default Tx switching behaviour, but was missing the fastpath change
required for FW to pass packets from PFs to VFs.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we receive a PTP event from the NIC when we haven't set up PTP state
in the driver, we attempt to read through a NULL pointer efx->ptp_data,
triggering a panic.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Acked-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without a shutdown handler, T4 cards behave very badly after a kexec.
Some firmware calls return errors indicating allocation failures, for
example. This is probably because thouse resources were not released by
a BYE message to the firmware, for example.

Using the remove handler guarantees we will use a well tested path.

With this patch I applied, I managed to use kexec multiple times and
probe and iSCSI login worked every time.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Driver was not re-setting sds ring count to 1 after failing
   to allocate msi-x interrupts.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o This patch reverts commit 1414abea
  (qlcnic: Restrict VF from configuring any VLAN mode.)
  This will allow same multicast address to be used with any VLAN
  instead of programming seperate (MAC, VLAN) tuples in adapter.
  This will help save some multicast filters.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Once interrupts are enabled, instead of using module parameters,
use flags (QLCNIC_MSI_ENABLED and QLCNIC_MSIX_ENABLED) set by driver
to check interrupt mode.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was treating -ve return value as success in case of
qlcnic_enable_msi_legacy() failure
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump all Mellanox driver versions.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>