Set MAC address length according to the 6LoWPAN link layer in use.
Bluetooth Low Energy uses 48 bit addressing while IEEE802.15.4 uses
64 bits.
Signed-off-by: NPatrik Flykt <patrik.flykt@linux.intel.com>
Reviewed-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Set BTLE MAC addresses that are 6 bytes long and not 8 bytes
that are used in other places with 6lowpan.
Signed-off-by: NPatrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The hci_bcm driver currently does not prepare/unprepare the clock and
goes directly to enable, but as the documentation for clk_enable says,
clk_prepare must be called before clk_enable.
Signed-off-by: NJohn Keeping <john@metanate.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
Signed-off-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid Windsor <dwindsor@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

trivial fix to spelling mistake in debug message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This field is never big enough to warrant 16-bitness.

8-bit accesses enjoy shorted encoding on i386/x86_64 than 16-bit
accesses:

	add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-10 (-10)
	function                                     old     new   delta
	loopback_setup                               169     164      -5
	ether_setup                                  148     143      -5
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using 16-bit ->hh_len doesn't save any memory, save some .text instead:

	add/remove: 0/0 grow/shrink: 1/6 up/down: 2/-19 (-17)
	function                                     old     new   delta
	neigh_update                                2312    2314      +2
	fwnet_header_cache                           199     197      -2
	eth_header_cache                             101      99      -2
	ip6_finish_output2                          2371    2368      -3
	vrf_finish_output6                          1522    1518      -4
	vrf_finish_output                           1413    1409      -4
	ip_finish_output2                           1627    1623      -4
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A driver may use build_skb() for received packets.
These SKBs then have a head_frag.

Since commit d7e8883c ("net: make GRO aware of
skb->head_frag"), GRO may build frag_list SKBs out of
head_frag received SKBs.
In such a case, the chained SKBs end up with a head_frag.

Commit 07b26c94 ("gso: Support partial splitting at
the frag_list pointer") adds partial segmentation of frag_list
SKB chains into individual SKBs.
However, this is not done if the chained SKBs have any
linear part, because the device may not be able to DMA
the private linear buffer.

A chained frag_list SKB with head_frag is wrongfully
detected in this case as having a private linear part
and thus falls back to software GSO, while in fact the
linear part is backed by a DMA page just like any other frag.

This causes low performance when forwarding those packets
that were built with build_skb()

Allow partial segmentation at the frag_list pointer for
chained SKBs with head_frag.

Note that such SKBs can only be created by GRO, when applied
to received packets with head_frag.
Also note that this change only affects the data path that
performs the partial segmentation at frag_list pointer, and
not any of the other more common data paths.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
l2tp: constify l2tp_session_get*() and l2tp_tunnel_find*()

Declare parameters of these functions as "const" where possible.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

l2tp_tunnel_find() and l2tp_tunnel_find_nth() don't modify "net".
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can
declare their "net" variable as "const".
Also constify "ifname" in l2tp_session_get_by_ifname().
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Benjamin Herrenschmidt says:

====================
ftgmac100: Rework batch 4 - Misc

This is v2 of the fourth batch of updates to the ftgmac100 driver.

This is a bunch of misc cleanups and fixes, such as properly
disabling HW checksum generation on AST2400 where it's known
to be broken and some chip init updates.

This also adds the ability to turn HW checksum on/off and
configure the ring sizes via ethtool.

v2 Fixes patch 1/10 (NETIF_F_HW_CSUM conversion)

The next (and last) batch will add a few more "features" such
as netpoll, multicast/promist, vlan offload...
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I haven't seen any improvement above that size on the machines
I've tested with.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We set an arbitrary max at 1024 since we pre-allocate the actual
descriptor arrays and skb arrays to the full size to keep the
code a bit simpler and avoid allocation failures in the reset
task.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear stale interrupts on entry, configure FIFO sizes, set FIFO
thresholds, configure interrupt mitigation.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The helpers just take space but don't provide much value. Simple
one line comments are more explanatory.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To remove more confusion. This function is about obtaining the
initial MAC address at driver probe time.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To avoid confusion with the ndo callback and generally be
clearer about the purpose of that function
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So features can be turned on/off via ethtool
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.

Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.

Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The documentation describes NETIF_F_IP_CSUM as deprecated
so let's switch to NETIF_F_HW_CSUM and use the helper to
handle unhandled protocols.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: patches for net-next

here are some patches for net/smc. Most important are
improvements for socket closing.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smc specifies IB_SEND_INLINE for IB_WR_SEND ib_post_send calls, but
provides a mapped buffer to be sent. This is inconsistent, since
IB_SEND_INLINE works without mapped buffer. Problem has not been
detected in the past, because tests had been limited to Connect X3 cards
from Mellanox, whose mlx4 driver just ignored the IB_SEND_INLINE flag.
For now, the IB_SEND_INLINE flag is removed.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure sockets never accepted are removed cleanly.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

unhash is already called in sock_put_work. Remove the second call.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

State SMC_CLOSED should be reached only, if ConnClosed has been sent to
the peer. If ConnClosed is received from the peer, a socket with
shutdown SHUT_WR done, switches errorneously to state SMC_CLOSED, which
means the peer socket is dangling. The local SMC socket is supposed to
switch to state APPFINCLOSEWAIT to make sure smc_close_final() is called
during socket close.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several state changes occur during SMC socket closing. Currently
state changes triggered locally occur in process context with
lock_sock() taken while state changes triggered by peer occur in
tasklet context with bh_lock_sock() taken. bh_lock_sock() does not
wait till a lock_sock(() task in process context is finished. This
may lead to races in socket state transitions resulting in dangling
SMC-sockets, or it may lead to duplicate SMC socket freeing.
This patch introduces a closing worker to run all state changes under
lock_sock().
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Reported-by: NDave Jones <davej@codemonkey.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wake up reading file descriptors for a closing socket as well, otherwise
some socket applications may stall.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If peer indicates write_blocked, the cursor state of the received data
should be send to the peer immediately (in smc_tx_consumer_update()).
Afterwards the write_blocked indicator is cleared.

If there is no free slot for another write request, sending is postponed
to worker smc_tx_work, and the write_blocked indicator is not cleared.
Therefore another clearing check is needed in smc_tx_work().
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMC requires an active ib port on the RoCE device.
smc_pnet_find_roce_resource() determines the matching RoCE device port
according to the configured PNET table. Do not return the found
RoCE device port, if it is not flagged active.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The global event handler is created only, if the ib_device has already
been used by at least one link group. It is guaranteed that there exists
the corresponding entry in the smc_ib_devices list. Get rid of this
superfluous check.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes an outdated comment.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the submission of the lastest multiple buffer patch set, this fix was lost.
I am sending this patch to put it right again. The fix was originally proposed
by Arnd Bergmann.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BPF helper functions access socket fields through skb->sk. This is not
set in ingress cgroup and socket filters. The association is only made
in skb_set_owner_r once the filter has accepted the packet. Sk is
available as socket lookup has taken place.

Temporarily set skb->sk to sk in these cases.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the return value check which testing the wrong variable
in devlink_dpipe_header_put().

Fixes: 1555d204 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
more s390/net updates

here's a second batch of s390/net patches for net-next.
A mixed bunch of qeth cleanups, and a few patches to add support for
ETHTOOL_GLINKSETTINGS.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

prepare() and complete() are not implemented by any discipline, so just
drop all the indirection.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NHans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LINK_MODE_* replaces the u32-limited SUPPORTED_* / ENABLED_*
definitions.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

get_settings() is deprecated and lacks support for higher link
speeds, so implement get_link_ksettings() instead.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>