platform_get_resource() may fail and return NULL, so we had better
check its return value to avoid a NULL pointer dereference a bit later
in the code. Fix it to use devm_platform_ioremap_resource_byname()
instead of calling platform_get_resource_byname() and devm_ioremap().

Fixes: 8425c41d ("net: ll_temac: Extend support to non-device-tree platforms")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NWang Hai <wanghai38@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.

Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: NVaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.

Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: NVaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.

Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: NVaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes coccicheck warning:

./drivers/net/ethernet/broadcom/bnxt/bnxt.c:3730:19-37: WARNING:
dma_alloc_coherent use in stats -> hw_stats already zeroes out
memory,  so memset is not needed

dma_alloc_coherent use in status already zeroes out memory,
so memset is not needed
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NLi Heng <liheng40@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The size of struct octeon_dispatch is too small, it is better to use
kmalloc instead of vmalloc.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NWang Hai <wanghai38@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the flex_array_size() helper to calculate the size of a
flexible array member within an enclosing structure.

This helper offers defense-in-depth against potential integer
overflows, while at the same time makes it explicitly clear that
we are dealing witha flexible array member.

Also, remove unnecessary pointer identifier sub_pool.
Signed-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Tested-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Acked-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mvneta has switched to phylink, so the comment should look
like "We may have called phylink_speed_down before".
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on PAGE_SIZE, the following unused parameter warning can be
reported:

drivers/net/ethernet/intel/ice/ice_txrx.c: In function ‘ice_rx_frame_truesize’:
drivers/net/ethernet/intel/ice/ice_txrx.c:513:21: warning: unused parameter ‘size’ [-Wunused-parameter]
        unsigned int size)

The 'size' variable is used only when PAGE_SIZE >= 8192. Add __maybe_unused
to remove the warning.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

For the FW logging info AQ command, we currently set the ICE_AQ_FLAG_RD
in order to work around a FW issue. This issue has been fixed so remove the
workaround.
Signed-off-by: NBen Shelton <benjamin.h.shelton@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The scope of the macro local variable 'i' can be reduced.  Do so to avoid
static analysis tools from complaining.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

As part of ice_setup_pf_sw() a PF VSI is setup; release the VSI in case of
failure.
Signed-off-by: NMarcin Szycik <marcin.szycik@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Currently the PF VSI's context parameters are left in a bad state when
going into safe mode. This is causing VLAN traffic to not pass. Fix this
by configuring the PF VSI to allow all VLAN tagged traffic.

Also, remove redundant comment explaining the safe mode flow in
ice_probe().
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

This is a port of i40e commit 70563957 ("i40e: need_wakeup flag might
not be set for Tx").

Quoting the original commit message:

"The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an interrupt
since interrupts are disabled in the napi poll loop) between the time we
stopped processing the Tx completions and interrupts are enabled again.
In this case, the need_wakeup flag will have been cleared at the end of
the Tx completion processing as we believe we will get an interrupt from
the outstanding completion at a later point in time. But if this
completion interrupt occurs before interrupts are enable, we lose it and
should at that point really have set the need_wakeup flag since there
are no more outstanding completions that can generate an interrupt to
continue the processing. When this happens, user space will see a Tx
queue need_wakeup of 0 and skip issuing a syscall, which means will
never get into the Tx processing again and we have a deadlock."

As a result, packet processing stops. This patch introduces a fix for
this issue, by always setting the need_wakeup flag at the end of an
interrupt processing. This ensures that the deadlock will not happen.
Signed-off-by: NKrzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Distribute the Tx queues evenly across all queue groups. This will
help the queues to get more equal sharing among the queues when all
are in use.

In the previous algorithm, the next queue group node will be picked up
only after the previous one filled with max children.
For example: if VSI is configured with 9 queues, the first 8 queues
will be assigned to queue group 1 and the 9th queue will be assigned to
queue group 2.

The 2 queue groups split the bandwidth between them equally (50:50).
The first queue group node will share the 50% bandwidth with all of
its children (8 queues). And the second queue group node will share
the entire 50% bandwidth with its only children.

The new algorithm will fix this issue.
Signed-off-by: NVictor Raj <victor.raj@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

By default the queues are configured in legacy mode. The default
BW settings for legacy/advanced modes are different. The existing
code was using the advanced mode default value of 1 which was
incorrect. This caused the unbalanced BW sharing among siblings.
The recommended default value is applied.
Signed-off-by: NTarun Singh <tarun.k.singh@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Mask bits before accessing the profile type field.
Signed-off-by: NTarun Singh <tarun.k.singh@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

If a user sets the value of the TX or RX descriptors to some non-default
value using 'ethtool -G' then we need to not overwrite the values when
we rebuild the VSI. The VSI rebuild could happen as a result of a user
setting the number of queues via the 'ethtool -L' command. Fix this by
checking to see if the value we have stored is non-zero and if it is
then don't change the value.
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Return ICE_ERR_DOES_NOT_EXIST return code if admin command error code is
ICE_AQ_RC_ENOENT (not exist). ice_aq_sw_rules is used when switch
rule is getting added/deleted/updated. In case of delete/update
switch rule, admin command can return ICE_AQ_RC_ENOENT error code
if such rule does not exist, hence return ICE_ERR_DOES_NOT_EXIST error
code from ice_aq_sw_rule, so that caller of this function can decide
how to handle ICE_ERR_DOES_NOT_EXIST.
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.

Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Signed-off-by: NNick Nunley <nicholas.d.nunley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

When the driver experiences a link event (especially link up)
there can be multiple events generated. Some of these are
link fault and still have a state of DOWN set.  The problem
happens when the link comes UP during the PF driver handling
one of the LINK DOWN events.  The status of the link is updated
and is now seen as UP, so when the actual LINK UP event comes,
the port information has already been updated to be seen as UP,
even though none of the UP activities have been completed.

After the link information has been updated in the link
handler and evaluated for MEDIA PRESENT, if the state
of the link has been changed to UP, treat the DOWN event
as an UP event since the link is now UP.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

After a GLOBR, the link was broken so that a link
up situation was being seen as a link down.

The problem was that the rebuild process was updating
the port_info link status without doing any of the
other things that need to be done when link changes.

This was causing the port_info struct to have current
"UP" information so that any further UP interrupts
were skipped as redundant.

The rebuild flow should *not* be updating the port_info
struct link information, so eliminate this and leave
it to the link event handling code.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

There is a bug where the LFC settings are not being preserved
through a link event.  The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.

On a link-up event, make sure that a set_local_mib is being
performed.

Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

When WoL is enabled and the machine is powered off, the PHY remains
waiting for wakeup events at max speed, which is a waste of energy.

Slow down the PHY speed before stopping the ethernet if WoL is enabled,
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the stmmac driver WOL implementation relies on MAC's PMT
feature. We have a case: the MAC HW doesn't enable PMT, instead, we
rely on the phy to support WOL. Implement the support for this case.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to prepare WOL support with phy. Compared with WOL
implementation which relies on the MAC's PMT features, in phy
supported WOL case, device_may_wakeup() may also be true, but we
should not call mac's pmt() function if HW doesn't enable PMT.

And during resume, we should call phylink_start() if PMT is disabled.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If !device_can_wakeup(), there's no need to futher check. And return
-EOPNOTSUPP rather than -EINVAL if !device_can_wakeup().
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove WAKE_MAGIC from supported modes if the HW capability register
shows no support for pmt_magic_frame.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

improve the error message when functions return failure and dump
relevant registers in some exception handling processes
Signed-off-by: NLuo bin <luobin9@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add support to handle hw abnormal event such as hardware failure,
cable unplugged,link error
Signed-off-by: NLuo bin <luobin9@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.

The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.

Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.

The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).

Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.

To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.

With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After a flash update, the pending status of the update can be determined
from the device capabilities.

Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: NCudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: NJacek Naczyk <jacek.naczyk@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow QSFP-DD transceivers temperature thresholds reading for hardware
monitoring and thermal control.

For this type, the thresholds are located in page 02h according to the
"Module and Lane Thresholds" description from Common Management
Interface Specification.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Quad Small Form Factor Pluggable Double Density (QSFP-DD) hardware
specification defines a form factor that supports up to 400 Gbps in
aggregate over an 8x50-Gbps electrical interface. The QSFP-DD supports
both optical and copper interfaces.

Implementation is based on Common Management Interface Specification;
Rev 4.0 May 8, 2019. Table 8-2 "Identifier and Status Summary (Lower
Page)" from this spec defines "Id and Status" fields located at offsets
00h - 02h. Bit 2 at offset 02h ("Flat_mem") specifies QSFP EEPROM memory
mode, which could be "upper memory flat" or "paged". Flat memory mode is
coded "1", and indicates that only page 00h is implemented in EEPROM.
Paged memory is coded "0" and indicates that pages 00h, 01h, 02h, 10h
and 11h are implemented. Pages 10h and 11h are currently not supported
by the driver.

"Flat" memory mode is used for the passive copper transceivers. For this
type only page 00h (256 bytes) is available. "Paged" memory is used for
the optical transceivers. For this type pages 00h (256 bytes), 01h (128
bytes) and 02h (128 bytes) are available. Upper page 01h contains static
advertising field, while upper page 02h contains the module-defined
thresholds and lane-specific monitors.

Extend enumerator 'mlxsw_reg_mcia_eeprom_module_info_id' with additional
field 'MLXSW_REG_MCIA_EEPROM_MODULE_INFO_TYPE_ID'. This field is used to
indicate for QSFP-DD transceiver type which memory mode is to be used.

Expose 256 bytes buffer for QSFP-DD passive copper transceiver and
512 bytes buffer for optical.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

list_for_each_entry is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.

Note that list_for_each_entry is defined in terms of list_first_entry,
which indicates that it should not be used on an empty list.  But in
list_for_each_entry, the element obtained by list_first_entry is not
really accessed, only the address of its list_head field is compared
to the address of the list head, so the list_first_entry is safe.

The semantic patch that makes this change is as follows (with another
variant for the no brace case): (http://coccinelle.lip6.fr/)

<smpl>
@@
expression x,e;
iterator name list_for_each_entry;
statement S;
identifier i;
@@

-if (!(list_empty(x))) {
   list_for_each_entry(i,x,...) S
- }
 ... when != i
? i = e
</smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

There is no need to print on each unsuccessful matcher
ip_version combination since it probably will happen when
trying to create all the possible combinations.
On a real failure we have a print in the calling function.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>