Add the ndo_busy_poll handler. Use skb_mark_napi_id to mark receive
packets with the napi id. For each slice, use per-slice spinlock and
state variable to ensure that only one handler processes receive
pacekts.

Locking, statistics counters, and the ndo_busy_poll handler follow
those in the ixgbe driver. So, credit goes to that driver's authors.
Signed-off-by: NHyong-Youb Kim <hykim@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When attempting to change e.g. the advertising mask when the link is down
ecmd->speed is -1 causing mii_ethtool_sset() to bail out.

This bug bit when connecting to a gigabit switch through a 4-pin (industrial)
cable, since link negotiation would not complete (both endpoints claimed to
be gigabit-capable, but this is not possible with only 4 pins).
Any attempt to fix this by setting autonegation to not offer 1000Mbps
failed as the setting would not be accepted while the link was still down...

Set ecmd->speed to SPEED_1000 to satisfy mii_ethtool_sset()
(the actual value of ecmd->speed doesn't matter as long as it is valid,
since a re-negotation is forced afterwards).
Signed-off-by: NAnders Larsen <al@alarsen.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the missing unlock before return from function moxart_mac_start_xmit()
in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool core will lower the requested length to the one returned by
get_regs_len, therefore no additional check is needed in the get_regs
function.
Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NPeter Wu <lekensteyn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch generates a hardware crash notification (NETDEV_REBOOT)
during reset. After a hardware crash, ENIC resets all its resources
including queue pair filters programmed by USNIC. USNIC registers for
this notification, and on receiving it, reprograms the queue pair
filters.
Signed-off-by: NNeel Patel <neepatel@cisco.com>
Signed-off-by: NNishank Trivedi <nistrive@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds an interface for USNIC to proxy firmware commands
through ENIC.
Signed-off-by: NNeel Patel <neepatel@cisco.com>
Signed-off-by: NNishank Trivedi <nistrive@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch,
    - Adds new firmware commands for the new Cisco Low Latency NIC
      (aka. USNIC).
Signed-off-by: NNeel Patel <neepatel@cisco.com>
Signed-off-by: NNishank Trivedi <nistrive@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Use appropriate firmware image file name based on device IDs.
Signed-off-by: NPratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Loopback initiator function drivers should process loopback time extend AEN.
  These AENs are triggered by the loopback time extend mailbox command
  issued by the target function drivers.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o 84xx adapters support VLAN stripping for PVID. Packets don't have
  VLAN tag inserted in case of PVID. So packet should follow non vlan path.

o Use capability bit to set PVID mode.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch allows transmit side vlan offload for vxlan
devices.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than having static headroom calculation, adjust headroom
according to target device.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch allows more code sharing between vxlan and ovs-vxlan.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch adds data field to vxlan socket and export
vxlan handler api.
vh->data is required to store private data per vxlan handler.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Once we have ovs-vxlan functionality, one UDP port can be assigned
to kernel-vxlan or ovs-vxlan port.  Therefore following patch adds
vxlan demux functionality, so that vxlan or ovs module can
register for particular port.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use iptunnel_pull_header() for better code sharing.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restructure vxlan-socket management APIs so that it can be
shared between vxlan and ovs modules.
This patch does not change any functionality.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
v6-v7:
 - get rid of zero refcnt vs from hashtable.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add comments.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split some parts of code into another function to simplify
tx_bottom(). Use while loop to replace the goto loop.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move some declearation of variables in rx_bottom().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Use r8152_get_tx_agg for getting tx agg list
- Replace submit rx with goto submit
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace lockflags with flags.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the type of contex of tx_agg and rx_agg from void * to
staruc r8152 *.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove memset(tp, 0, sizeof(*tp));
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the previous QUERY_PAGES command version we used one command to get the
required amount of boot, init and post init pages.  The new version uses the
op_mod field to specify whether the query is for the required amount of boot,
init or post init pages. In addition the output field size for the required
amount of pages increased from 16 to 32 bits.

In MANAGE_PAGES command the input_num_entries and output_num_entries fields
sizes changed from 16 to 32 bits and the PAS tables offset changed to 0x10.

In the pages request event the num_pages field also changed to 32 bits.

In the HCA-capabilities-layout the size and location of max_qp_mcg field has
been changed to support 24 bits.

This patch isn't compatible with firmware versions < 5; however, it  turns out that the
first GA firmware we will publish will not support previous versions so this should be OK.
Signed-off-by: NMoshe Lazer <moshel@mellanox.com>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent fix d9bf5f13 "tun: compare with 0 instead of total_len" is
not totally correct.  Because "len" and "sizeof()" are size_t type, that
means they are never less than zero.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Load firmware from file before setting up interrupts.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Driver was hitting a panic at the time of adapter reset due to invalid command
  access from the list which had been already freed by the queuing thread.
  Flush all the pending commands from the list before proceeding with adapter reset
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o After firmware reset VFs were failing to come up because of not
  reinitializing mailbox data structures. Reinitialize them so that
  VFs can come up after firmware reset.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Do not allow interrupt test when adapter is resetting.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Driver was misinterpreting the return status for beacon
  state query leading to incorrect interpretation of beacon
  state and logging an error message for successful status.
  Fixed the driver to properly interpret the return status.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was issuing set driver version command through all
functions in the adapter. Fix the driver to issue set driver
version once per adapter, through function 0.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d8af4dfd ("net/tg3: Fix kernel crash") introduced a possible
NULL pointer dereference in tg3 driver when !netdev || !netif_running(netdev)
condition is met and netdev is NULL. Then, the jump to the 'done' label
calls dev_close() with a netdevice that is NULL. Therefore, only call
dev_close() when we have a netdevice, but one that is not running.

[ Add the same checks in tg3_io_slot_reset() per Gavin Shan - by Nithin
Nayak Sujir ]
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>