Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 22 11月, 2019 32 次提交
  3. 21 11月, 2019 8 次提交
    • R
      net: sfp: soft status and control support · f3c9a666
      由 Russell King 提交于 
      Add support for the soft status and control register, which allows
TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set.  We
make use of this when the board does not support GPIOs for these
signals.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f3c9a666
    • D
      Merge branch 'sfp-quirks' · 9ce33351
      由 David S. Miller 提交于 
      Russell King says:

====================
Add rudimentary SFP module quirk support

The SFP module EEPROM describes the capabilities of the module, but
doesn't describe the host interface.  We have a certain amount of
guess-work to work out how to configure the host - which works most
of the time.

However, there are some (such as GPON) modules which are able to
support different host interfaces, such as 1000BASE-X and 2500BASE-X.
The module will switch between each mode until it achieves link with
the host.

There is no defined way to describe this in the SFP EEPROM, so we can
only recognise the module and handle it appropriately.  This series
adds the necessary recognition of the modules using a quirk system,
and tweaks the support mask to allow them to link with the host at
2500BASE-X, thereby allowing the user to achieve full line rate.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9ce33351
    • R
      net: sfp: add some quirks for GPON modules · b0eae33b
      由 Russell King 提交于 
      Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P
modules are capable of 2500base-X, but incorrectly report their
capabilities in the EEPROM.  It seems rather common that GPON modules
mis-report.

Let's fix these modules by adding some quirks.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b0eae33b
    • R
      net: sfp: add support for module quirks · b34bb2cb
      由 Russell King 提交于 
      Add support for applying module quirks to the list of supported
ethtool link modes.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b34bb2cb
    • H
      tcp: warn if offset reach the maxlen limit when using snprintf · 9bb59a21
      由 Hangbin Liu 提交于 
      snprintf returns the number of chars that would be written, not number
of chars that were actually written. As such, 'offs' may get larger than
'tbl.maxlen', causing the 'tbl.maxlen - offs' being < 0, and since the
parameter is size_t, it would overflow.

Since using scnprintf may hide the limit error, while the buffer is still
enough now, let's just add a WARN_ON_ONCE in case it reach the limit
in future.

v2: Use WARN_ON_ONCE as Jiri and Eric suggested.
Suggested-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9bb59a21
    • W
      ip_gre: Make none-tun-dst gre tunnel store tunnel info as metadat_dst in recv · c0d59da7
      由 wenxu 提交于 
      Currently collect_md gre tunnel will store the tunnel info(metadata_dst)
to skb_dst.
And now the non-tun-dst gre tunnel already can add tunnel header through
lwtunnel.

When received a arp_request on the non-tun-dst gre tunnel. The packet of
arp response will send through the non-tun-dst tunnel without tunnel info
which will lead the arp response packet to be dropped.

If the non-tun-dst gre tunnel also store the tunnel info as metadata_dst,
The arp response packet will set the releted tunnel info in the
iptunnel_metadata_reply.

The following is the test script:

ip netns add cl
ip l add dev vethc type veth peer name eth0 netns cl

ifconfig vethc 172.168.0.7/24 up
ip l add dev tun1000 type gretap key 1000

ip link add user1000 type vrf table 1
ip l set user1000 up
ip l set dev tun1000 master user1000
ifconfig tun1000 10.0.1.1/24 up

ip netns exec cl ifconfig eth0 172.168.0.17/24 up
ip netns exec cl ip l add dev tun type gretap local 172.168.0.17 remote 172.168.0.7 key 1000
ip netns exec cl ifconfig tun 10.0.1.7/24 up
ip r r 10.0.1.7 encap ip id 1000 dst 172.168.0.17 key dev tun1000 table 1

With this patch
ip netns exec cl ping 10.0.1.1 can success
Signed-off-by: Nwenxu <wenxu@ucloud.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c0d59da7
    • D
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next · ee5a489f
      由 David S. Miller 提交于 
      Daniel Borkmann says:

====================
pull-request: bpf-next 2019-11-20

The following pull-request contains BPF updates for your *net-next* tree.

We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).

There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca7:

<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca7

<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca7

<<<<<<< HEAD
        if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
        /* kmalloc()'ed memory can't be mmap()'ed */
        if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca7

The main changes are:

1) Addition of BPF trampoline which works as a bridge between kernel functions,
   BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
   BPF programs for tracing with practically zero overhead to call into BPF (as
   opposed to k[ret]probes) and ii) attachment of the former to networking related
   programs to see input/output of networking programs (covering xdpdump use case),
   from Alexei Starovoitov.

2) BPF array map mmap support and use in libbpf for global data maps; also a big
   batch of libbpf improvements, among others, support for reading bitfields in a
   relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.

3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
   the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.

4) Add BPF audit support and emit messages upon successful prog load and unload in
   order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.

5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
   (XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.

6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
   call named bpf_get_link_xdp_info() for retrieving the full set of prog
   IDs attached to XDP, from Toke Høiland-Jørgensen.

7) Add BTF support for array of int, array of struct and multidimensional arrays
   and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.

8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.

9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
   xdping to be run as standalone, from Jiri Benc.

10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.

11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.

12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
    samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ee5a489f
    • D
      bpf: Switch bpf_map_{area_alloc,area_mmapable_alloc}() to u64 size · 196e8ca7
      由 Daniel Borkmann 提交于 
      Given we recently extended the original bpf_map_area_alloc() helper in
commit fc970227 ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"),
we need to apply the same logic as in ff1c08e1 ("bpf: Change size
to u64 for bpf_map_{area_alloc, charge_init}()"). To avoid conflicts,
extend it for bpf-next.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
      196e8ca7