I posted this last month, but was prompted to do so again in bz#467457

Add capability flag to support slave devices with pata_sch driver.
Signed-off-by: NMark Salter <msalter@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

No arguments named @deadline in cs5535_cable_detect() and
cs5536_cable_detect().  Remove them.
Signed-off-by: NQinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch reverts the following three commits which convert libata to
use block layer tagging.

 43a49cbd
 e013e13b
 2fca5ccf

Although using block layer tagging is the right direction, due to the
tight coupling among tag number, data structure allocation and
hardware command slot allocation, libata doesn't work correctly with
the current conversion.

The biggest problem is guaranteeing that tag 0 is always used for
non-NCQ commands.  Due to the way blk-tag is implemented and how SCSI
starts and finishes requests, such guarantee can't be made.  I'm not
sure whether this would actually break any low level driver but it
doesn't look like a good idea to break such assumption given the
frailty of ATA controllers.

So, for the time being, keep using the old dumb in-libata qc
allocation.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jens Axobe <jens.axboe@oracle.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling.  Mask off DET when restoring
SControl.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers.  Implement a horkage to skip the mod16 check and apply
it to the quantum device.

This is reported by John Clark in the following thread.

  http://thread.gmane.org/gmane.linux.ide/34748Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

All three flavors of sata_nv's are different in how their hardreset
behaves.

* generic: Hardreset is not reliable.  Link often doesn't come online
  after hardreset.

* nf2/3: A little bit better - link comes online with longer debounce
  timing.  However, nf2/3 can't reliable wait for the first D2H
  Register FIS, so it can't wait for device readiness or classify the
  device after hardreset.  Follow-up SRST required.

* ck804: Hardreset finally works.

The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors.  This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

commit b9d5b89b (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it

catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.

The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.

To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.

So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

5287 used to be treated as vt6420 but it didn't work.  It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports.  This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata.  Another controller
which falls into this category is ata_piix w/ SIDPR access.

libata now has facility to deal with this class of controllers named
slave_link.  A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.

This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.

This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

In ata_tf_to_lba48(), when evaluating

	(tf->hob_lbal & 0xff) << 24

the expression is promoted to signed int (since int can hold all values
of u8).  However, if hob_lbal is 128 or more, then it is treated as a
negative signed value and sign-extended when promoted to u64 to | into
sectors, which leads to the MSB 32 bits of section getting set
incorrectly.

For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported
that a 1.5GB drive caused:

    ata3.00: HPA detected: current 2930277168, native 18446744072344861488

where 2930277168 == 0xAEA87B30 and 18446744072344861488 == 0xffffffffaea87b30
which shows the problem when hob_lbal is 0xae.

Fix this by adding a cast to u64, just as is used by for hob_lbah and
hob_lbam in the function.
Reported-by: NPhillip O'Donnell <phillip.odonnell@gmail.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove excess kernel-doc function parameter notation from drivers/ata/:

Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Enclosure management bit mask definitions.
Signed-off-by: NDavid Milburn <dmilburn@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.
Signed-off-by: NDavid Milburn <dmilburn@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

[http://lkml.org/lkml/2008/10/18/82]
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed.  These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Due to request posting limitations, bandwidth of sil3132 is limited to
around 120MB/s with the minimum pci-e payload size (128bytes) which is
used by most consumer systems.  However, write throughput can be
slightly (~3%) increased by increasing the max read requeset size.
Configure it to 4k which is the maximum supported.  This optimization
is also done by SIMG's windows driver.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix libata missing kernel-doc:

Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description
found for parameter 'tag'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.

* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()

While at it, reformat comments in cable_is_40wire().
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.

This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.

Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.

Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.
Signed-off-by: NMark Nelson <mdnelson8@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The recent commit 2fca5ccf ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices

The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list.  So we need to check for
-1 first and only use the tag field if it's valid.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Reported-by: NAlexander Beregalov <a.beregalov@gmail.com>
Tested-by: NPaul Mundt <lethal@linux-sh.org>
Tested-by: NDave Young <hidave.darkstar@gmail.com>
Tested-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

VIA controllers clear DEVICE register when IEN changes.  Make sure
DEVICE is updated along with CTL.

This change is separated from Joseph Chan's larger patch.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reset methods don't have access to phys link status for slave links
and may incorrectly indicate device presence causing unnecessary probe
failures for unoccupied links.  This patch clears device class to NONE
during post-reset processing if phys link is offline.

As on/offlineness semantics is strictly defined and used in multiple
places by the core layer, this won't change behavior for drivers which
don't use slave links.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Slave link action mask is transferred to master link and all the EH
actions are taken by the master link.  ata_eh_about_to_do() and
ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave
link actions during transfer.  This always sets ATA_PFLAG_RECOVERED
flag causing spurious "EH complete" messages.

Don't set ATA_PFLAG_RECOVERED for slave link actions.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH.  As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.

This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ata_sff_post_internal_cmd() needs to grab port lock before calling
ata_bmdma_stop() and also need to clear hsm_task_state.  Fix it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ap->port_task was not initialized if !CONFIG_ATA_SFF later triggering
lockdep warning.  Make sure it's initialized.

Reported by Larry Finger.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As of version 2.0, ACPI can return 64-bit integers.  The current
acpi_evaluate_integer only supports 64-bit integers on 64-bit platforms.
Change the argument to take a pointer to an acpi_integer so we support
64-bit integers on all platforms.

lenb: replaced use of "acpi_integer" with "unsigned long long"
lenb: fixed bug in acpi_thermal_trips_update()
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

When no interrupt is specified the pata_of_platform fills the irq_res
resource with -1, which is wrong to do for two reasons:

1. By definition, 'no irq' should be IRQ 0, not some negative integer;
2. pata_platform checks for irq_res.start > 0, but since irq_res.start
   is unsigned type, the check will be true for `-1'.
Reported-by: NSteven A. Falco <sfalco@harris.com>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.

Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: NMike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch updates the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Resets make ATAPI devices raise UNIT ATTENTION which fails the next
command.  As resets can happen asynchronously for unrelated reasons,
this sometimes disrupts innocent users.  For example, reading DVD
fails after the system wakes up from suspend or the other device
sharing the channel went through bus error.

Clearing UA has some problems as it might clear UA which the userland
needs to know about.  However, UA after resets can only be about the
reset itself and benefits of clearing it overweights cons.  Missing UA
can only delay failure to one of the following commands anyway.  For
example, timeout while burning is in progress will trigger reset and
reset the device state and probably corrupt the burning run.  Although
the userland application won't get the UA, its pending writes will
fail.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>