This patch drops unnecessary target_core_fabric_ops parameter usage
for core_tpg_register() during fabric driver TFO->fabric_make_tpg()
se_portal_group creation callback execution.

Instead, use the existing se_wwn->wwn_tf->tf_ops pointer to ensure
fabric driver is really using the same TFO provided at module_init
time.

Also go ahead and drop the forward TFO declarations tree-wide, and
handling the special case for iscsi-target discovery TPG.

Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Detected these variables by building with W=1.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.

For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.

(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that struct se_portal_group contains a protocol identifier field we can
take all the code to format an parse protocol identifiers in CDBs into common
code instead of leaving this to low-level drivers.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that we store the protocol identifier in the tpg structure we don't
need this method.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

By always allocating and adding, respectively removing and freeing
the se_node_acl structure in core code we can remove tons of repeated
code in the init_nodeacl and drop_nodeacl routines.  Additionally
this now respects the get_default_queue_depth method in this code
path as well.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

All fabric drivers except for iSCSI always return 1, so implement
that as default behavior.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The first argument of these two functions is always identical
to se_cmd->se_sess. Hence remove the first argument.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

We don't assign pi_ctx to desc->pi_ctx until we're certain to succeed
in the function.  That means the cleanup path should use the local
pi_ctx variable, not desc->pi_ctx.

This was detected by Coverity (CID 1260062).
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Currently, iflink of the parent interface was always accessed, even
when interface didn't have a parent and hence we crashed there.

Handle the interface types properly: for a child interface, return
the ifindex of the parent, for parent interface, return its ifindex.

For child devices, make sure to set the parent pointer prior to
invoking register_netdevice(), this allows the new ndo to be called
by the stack immediately after the child device is registered.

Fixes: 5aa7add8 ('infiniband/ipoib: implement ndo_get_iflink')
Reported-by: NHonggang Li <honli@redhat.com>
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NHonggang Li <honli@redhat.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>+
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some rare cases, IO operations may be not aligned to page
boundaries. This prevents iser from performing fast memory
registration. In order to overcome that iser uses a bounce
buffer to carry the transaction. We basically allocate a buffer
in the size of the transaction and perform a copy.

The buffer allocation using kmalloc is too restrictive since it
requires higher order (atomic) allocations for large transactions
(which may result in memory exhaustion fairly fast for some workloads).
We rewrite the bounce buffer code path to allocate scattered pages
and perform a copy between the transaction sg and the bounce sg.
Reported-by: NAlex Lyakas <alex@zadarastorage.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In singleton scatterlists, DMA memory registration code
is taken both for Fastreg and FMR code paths. Move it to
a function.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Instead of passing ib_sge as output variable, we pass the mem_reg
pointer to have the routines fill the rkey as well. This reduces
code duplication and extra assignments. This is a preparation step
to unify some registration logics together. Also, pass iser_fast_reg_mr
the fastreg descriptor directly.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

No need to keep lkey, va, len variables, we can keep
them as struct ib_sge. This will help when we change the
memory registration logic.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Memory regions are resources that are saved
in the device caches. Increase the probability for
a cache hit by adding the MRU descriptor to pool
head.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Make iser_[create|destroy]_fastreg_desc shorter, more
readable and easily extendable.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Instead of open-coding connection fastreg pool get/put,
we introduce iser_reg_desc[get|put] helpers.

We aren't setting these static as this will be a per-device
routine later on. Also, cleanup iser_unreg_rdma_mem_fastreg
a bit.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

No need for these two separate. Keep it in a single routine
like in the fastreg case. This will also make iser_reg_page_vec
closer to iser_fast_reg_mr arguments. This is a preparation
step for registration flow refactor.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This struct members other than struct iser_mem_reg are unused,
so remove it altogether.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Buffer length was assigned twice, and no reason to set va to
io_addr and then add the offset, just set va to io_addr + offset.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

As memory registration/de-registration methods, lets
move them to their natural location. While we're at it,
make iser_reg_page_vec routine static.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

No need to pass that, we can take it from the task.
In a later stage, this function will be invoked
according to a device capability.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

No need to keep two iser_data_buf structures just in case we use
mem copy. We can avoid that just by adding a pointer to the original
sg. So keep only two iser_data_buf per command (data and protection)
and pass the relevant data_buf to bounce buffer routine.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This code was added before we had protection data length
calculation (in iser_send_command), so we needed to calc
the sg data length from the sg itself. This is not needed
anymore.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAdir Lev <adirl@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This length miss-calculation may cause a silent data corruption
in the DIX case and cause the device to reference unmapped area.

Fixes: d77e6535 ('libiscsi, iser: Adjust data_length to include protection information')
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fast registration and local invalidate work requests can
also fail. We should call error completion handler for them.
Reported-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In case the user unloaded ib_iser while ep_connect is in
progress, we need to destroy the endpoint although ep_disconnect
wasn't invoked (we detect this by the iser conn state != DOWN).
However, if we got an REJECTED/UNREACHABLE CM event we move the
connection state to DOWN which will prevent us from destroying
the endpoint in the module unload stage. Fix this by setting the
connection state to TERMINATING in iser_conn_error so we can still
destroy the endpoint at unload stage.
Reported-by: NAriel Nahum <arieln@mellanox.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The driver already defined the pr_format, it just hadn't
been converted to use pr_info, pr_warn, and pr_err instead
of the equivalent printks.  Convert so that messages from
the driver are now properly tagged with their driver name
and can be more easily debugged.

In addition, a number of these printk's were not newline
terminated, so fix that at the same time.
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This change slightly reduces the time needed to log in.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NDavid Dillow <dave@thedillows.org>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

After Doug Ledford's changes there is no need in that bit, it's
semantic becomes subset of the IPOIB_FLAG_OPER_UP bit.
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Whenever there is no path->ah to the destination, keep only defined
number of skb's. Otherwise there are cases that the driver can keep
infinite list of skb's.

For example, when one device want to send unicast arp to the destination,
and from some reason the SM doesn't respond, the driver currently keeps
all the skb's. If that unicast arp traffic stopped, all  these skb's
are kept by the path object till the interface is down.
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

As the result of a completion error the QP can moved to SQE state by
the hardware. Since it's not the Error state, there are no flushes
and hence the driver doesn't know about that.

The fix creates a task that after completion with error which is not a
flush tracks the QP state and if it is in SQE state moves it back to RTS.
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Update the cached broadcast record in the priv object after every new
join of this broadcast domain group.

These values are needed for the port configuration (MTU size) and to
all the new multicast (non-broadcast) join requests initial parameters.

For example, SM starts with 2K MTU for all the fabric, and after that it
restarts (or handover to new SM) with new port configuration of 4K MTU.
Without using the new values, the driver will keep its old configuration
of 2K and will not apply the new configuration of 4K.
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The current code in the RX flow uses two sg entries for each incoming
packet, the first one was for the IB headers and the second for the rest
of the data, that causes two  dma map/unmap and two allocations, and few
more actions that were done at the data path.

Use only one linear skb on each incoming packet, for the data (IB
headers and payload), that reduces the packet processing in the
data-path (only one skb, no frags, the first frag was not used anyway,
less memory allocations) and the dma handling (only one dma map/unmap
over each incoming packet instead of two map/unmap per each incoming packet).

After commit 73d3fe6d ("gro: fix aggregation for skb using frag_list") from
Eric Dumazet, we will get full aggregation for large packets.

When running bandwidth tests before and after the (over the card's numa node),
using "netperf -H 1.1.1.3 -T -t TCP_STREAM", the results before are ~12Gbs before
and after ~16Gbs on my setup (Mellanox's ConnectX3).
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

We needed the mcast_mutex when we had to prevent the join completion
callback from having the value it stored in mcast->mc overwritten
by a delayed return from ib_sa_join_multicast.  By storing the return
of ib_sa_join_multicast in an intermediate variable, we prevent a
delayed return from ib_sa_join_multicast overwriting the valid
contents of mcast->mc, and we no longer need a mutex to force the
join callback to run after the return of ib_sa_join_multicast.  This
allows us to do away with the mutex entirely and protect our critical
sections with a just a spinlock instead.  This is highly desirable
as there were some places where we couldn't use a mutex because the
code was not allowed to sleep, and so we were currently using a mix
of mutex and spinlock to protect what we needed to protect.  Now we
only have a spin lock and the locking complexity is greatly reduced.
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Allow the ipoib layer to attempt to join all outstanding multicast
groups at once.  The ib_sa layer will serialize multiple attempts to
join the same group, but will process attempts to join different groups
in parallel.  Take advantage of that.

In order to make this happen, change the mcast_join_thread to loop
through all needed joins, sending a join request for each one that we
still need to join.  There are a few special cases we handle though:

1) Don't attempt to join anything but the broadcast group until the join
of the broadcast group has succeeded.
2) No longer restart the join task at the end of completion handling.
If we completed successfully, we are done.  The join task now needs kicked
either by mcast_send or mcast_restart_task or mcast_start_thread, but
should not need started anytime else except when scheduling a backoff
attempt to rejoin.
3) No longer use separate join/completion routines for regular and
sendonly joins, pass them all through the same routine and just do the
right thing based on the SENDONLY join flag.
4) Only try to join a SENDONLY join twice, then drop the packets and
quit trying.  We leave the mcast group in the list so that if we get a
new packet, all that we have to do is queue up the packet and restart
the join task and it will automatically try to join twice and then
either send or flush the queue again.
Signed-off-by: NDoug Ledford <dledford@redhat.com>