Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 28 5月, 2014 11 次提交
  3. 17 4月, 2014 2 次提交
  5. 05 12月, 2013 1 次提交
  7. 04 12月, 2013 3 次提交
  9. 26 7月, 2013 1 次提交
  11. 18 6月, 2013 1 次提交
    • G
      USB: cdc-acm: remove unneeded spin_lock_irqsave/restore on write path · 71c2fb03
      由 Greg Kroah-Hartman 提交于 
      When writing data we were:
	lock
	do some work
	unlock
	call function
		lock
		do some work
		unlock
		return
	return

It turns out, that "function" was only ever called in the one place, so
instead of locking/unlocking for no good reason, just inline the
function and only grab the lock once.

This has sped up the pathological case of sending 1 byte packets to a
loop-back cdc-acm device from 49600 bytes per second to 50100 bytes a
second on my workstation.  A tiny increase yes, but noticable, and now
the spinlock isn't the hottest thing on the perf graph anymore.  Yes, we
are still waiting for the hardware for the most part, but getting rid of
a spinlock_irq_save() call for every packet is still a good thing.

And we end up deleting lines of code, always a win overall.

This was found by using a Teensy 3.0 device and the test program and
firmware located at:
	http://www.pjrc.com/teensy/benchmark_usb_serial_receive.htmlReported-by: NPaul Stoffregen <paul@pjrc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      71c2fb03
  13. 22 3月, 2013 2 次提交
  15. 19 3月, 2013 2 次提交
  17. 16 3月, 2013 1 次提交
  19. 12 3月, 2013 1 次提交
  21. 16 1月, 2013 2 次提交
    • J
      TTY: switch tty_flip_buffer_push · 2e124b4a
      由 Jiri Slaby 提交于 
      Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.

Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.

IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.

Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      2e124b4a
    • J
      TTY: switch tty_insert_flip_string · 05c7cd39
      由 Jiri Slaby 提交于 
      Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.

tty_insert_flip_string this time.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      05c7cd39
  23. 12 1月, 2013 1 次提交
  25. 16 11月, 2012 1 次提交
  27. 18 10月, 2012 2 次提交
  29. 12 10月, 2012 1 次提交
  31. 06 9月, 2012 1 次提交
  33. 18 8月, 2012 1 次提交
  35. 14 8月, 2012 1 次提交
    • J
      TTY: use tty_port_register_device · 734cc178
      由 Jiri Slaby 提交于 
      Currently we have no way to assign tty->port while performing tty
installation. There are two ways to provide the link tty_struct =>
tty_port. Either by calling tty_port_install from tty->ops->install or
tty_port_register_device called instead of tty_register_device when
the device is being set up after connected.

In this patch we modify most of the drivers to do the latter. When the
drivers use tty_register_device and we have tty_port already, we
switch to tty_port_register_device. So we have the tty_struct =>
tty_port link for free for those.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      734cc178
  37. 17 7月, 2012 1 次提交
  39. 07 7月, 2012 1 次提交
  41. 15 6月, 2012 1 次提交
  43. 19 5月, 2012 1 次提交
    • S
      USB: Disable hub-initiated LPM for comms devices. · e1f12eb6
      由 Sarah Sharp 提交于 
      Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      e1f12eb6
  45. 09 3月, 2012 1 次提交