The whole purpose of tag_8021q is to send VLAN-tagged traffic to the
CPU, from which the driver can decode the source port and switch id.

Currently this only works if the VLAN filtering on the master is
disabled. Change that by explicitly adding code to tag_8021q.c to add
the VLANs corresponding to the tags to the filter of the master
interface.

Because we now need to call vlan_vid_add, then we also need to hold the
RTNL mutex. Propagate that requirement to the callers of dsa_8021q_setup
and modify the existing call sites as appropriate. Note that one call
path, sja1105_best_effort_vlan_filtering_set -> sja1105_vlan_filtering
-> sja1105_setup_8021q_tagging, was already holding this lock.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most DSA switch tags shift the EtherType to the right, causing the
master to not parse the VLAN as VLAN.
However, not all switches do that (example: tail tags, tag_8021q etc),
and if the DSA master has "rx-vlan-filter: on" in ethtool -k, then we
have a problem.

Therefore, we could populate the VLAN table of the master, just in case
(for some switches it will not make a difference), so that network I/O
can work even with a VLAN filtering master.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the bridge has VLAN awareness disabled there isn't any duplication
of functionality, since the bridge does not process VLAN. Don't deny
adding 8021q uppers to DSA switch ports in that case. The switch is
supposed to simply pass traffic leaving the VLAN tag as-is, and the
stack will happily strip the VLAN tag for all 8021q uppers that exist.

We need to ensure that there are no 8021q uppers when the user attempts
to enable bridge vlan_filtering.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current logic beats me a little bit. The comment that "bridge skips
-EOPNOTSUPP, so skip the prepare phase" was introduced in commit
fb2dabad ("net: dsa: support VLAN filtering switchdev attr").

I'm not sure:
(a) ok, the bridge skips -EOPNOTSUPP, but, so what, where are we
    returning -EOPNOTSUPP?
(b) even if we are, and I'm just not seeing it, what is the causality
    relationship between the bridge skipping -EOPNOTSUPP and DSA
    skipping the prepare phase, and just returning zero?

One thing is certain beyond doubt though, and that is that DSA currently
refuses VLAN filtering from the "commit" phase instead of "prepare", and
that this is not a good thing:

ip link add br0 type bridge
ip link add br1 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br1
[ 3790.379389] 001: sja1105 spi0.1: VLAN filtering is a global setting
[ 3790.379399] 001: ------------[ cut here ]------------
[ 3790.379403] 001: WARNING: CPU: 1 PID: 515 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 3790.379420] 001: swp3: Commit of attribute (id=6) failed.
[ 3790.379533] 001: [<c11ff588>] (switchdev_port_attr_set_now) from [<c11b62e4>] (nbp_vlan_init+0x84/0x148)
[ 3790.379544] 001: [<c11b62e4>] (nbp_vlan_init) from [<c11a2ff0>] (br_add_if+0x514/0x670)
[ 3790.379554] 001: [<c11a2ff0>] (br_add_if) from [<c1031b5c>] (do_setlink+0x38c/0xab0)
[ 3790.379565] 001: [<c1031b5c>] (do_setlink) from [<c1036fe8>] (__rtnl_newlink+0x44c/0x748)
[ 3790.379573] 001: [<c1036fe8>] (__rtnl_newlink) from [<c1037328>] (rtnl_newlink+0x44/0x60)
[ 3790.379580] 001: [<c1037328>] (rtnl_newlink) from [<c10315fc>] (rtnetlink_rcv_msg+0x124/0x2f8)
[ 3790.379590] 001: [<c10315fc>] (rtnetlink_rcv_msg) from [<c10926b8>] (netlink_rcv_skb+0xb8/0x110)
[ 3790.379806] 001: ---[ end trace 0000000000000002 ]---
[ 3790.379819] 001: sja1105 spi0.1 swp3: failed to initialize vlan filtering on this port

So move the current logic that may fail (except ds->ops->port_vlan_filtering,
that is way harder) into the prepare stage of the switchdev transaction.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is checking for the following order of operations, and makes sure
to deny that configuration:

ip link add link swp2 name swp2.100 type vlan id 100
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan add dev swp2 vid 100

Instead of using vlan_for_each(), which looks at the VLAN filters
installed with vlan_vid_add(), just track the 8021q uppers. This has the
advantage of freeing up the vlan_vid_add() call for actual VLAN
filtering.

There is another change in this patch. The check is moved in slave.c,
from switch.c. I don't think it makes sense to have this 8021q upper
check for each switch port that gets notified of that VLAN addition
(these include DSA links and CPU ports, we know those can't have 8021q
uppers because they don't have a net_device registered for them), so
just do it in slave.c, for that one slave interface.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSA tries to prevent having a VLAN added by a bridge and by an 802.1Q
upper at the same time. It does that by checking the VID in
.ndo_vlan_rx_add_vid(), since that's something that the 8021q module
calls, via vlan_vid_add(). When a VLAN matches in both subsystems, this
check returns -EBUSY.

However the vlan_vid_add() function isn't specific to the 8021q module
in any way at all. It is simply the kernel's way to tell an interface to
add a VLAN to its RX filter and not drop that VLAN. So there's no reason
to return -EBUSY when somebody tries to call vlan_vid_add() for a VLAN
that was installed by the bridge. The proper behavior is to accept that
configuration.

So what's wrong is how DSA checks that it has an 8021q upper. It should
look at the actual uppers for that, not just assume that the 8021q
module was somewhere in the call stack of .ndo_vlan_rx_add_vid().
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We'll be adding a new check in the PRECHANGEUPPER notifier, where we'll
need to check some VLAN uppers. It is hard to do that when there is
already a function named dsa_slave_upper_vlan_check. So rename this one.

Not to mention that this function probably shouldn't have started with
"dsa_slave_" in the first place, since the struct net_device argument
isn't a DSA slave, but an 8021q upper of one.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There doesn't seem to be any strong technical reason for doing it this
way, but we'll be adding more checks for invalid upper device
configurations, and it will be easier to have them all grouped under
PRECHANGEUPPER.

Tested that it still works:
ip link set br0 type bridge vlan_filtering 1
ip link add link swp2 name swp2.100 type vlan id 100
ip link set swp2.100 master br0
[   20.321312] br0: port 5(swp2.100) entered blocking state
[   20.326711] br0: port 5(swp2.100) entered disabled state
Error: dsa_core: Cannot enslave VLAN device into VLAN aware bridge.
[   20.346549] br0: port 5(swp2.100) entered blocking state
[   20.351957] br0: port 5(swp2.100) entered disabled state
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following W=1 kernel build warning(s):

drivers/net/ethernet/marvell/mvneta.c:754:6: warning:
 variable 'dummy' set but not used [-Wunused-but-set-variable]
  754 |  u32 dummy;
      |      ^~~~~

This variable is not used in function mvneta_mib_counters_clear(), so
remove it to avoid build warning.
Signed-off-by: NZhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When budget is non-zero, skb_unref() has already handled the
NULL checking.

When budget is zero, the dev_consume_skb_any() has handled NULL
checking in __dev_kfree_skb_irq(), or dev_kfree_skb() which also
ultimately call skb_unref().

So remove the unnecessary checking in napi_consume_skb().
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid copying skb_shared_info frags array in mvneta_swbm_build_skb() since
__build_skb_around() does not overwrite it
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We go to lengths to determine whether the PVID should be set
for this port or not, and then fail to take it into account.
Fix this oversight.

Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dan Murphy says:

====================
100base Fx link modes

As per patch https://lore.kernel.org/patchwork/patch/1300241/ the link
modes for 100base FX full and half duplex modes did not exist.  Adding
these link modes to the core and ethtool allow devices like the
DP83822, DP83869 and Broadcomm PHYs to properly advertise the correct
mode for Fiber 100Mbps.

Corresponding user land ethtool patches are available but rely on
these patches to be applied first.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the fiber advertisement for speed and duplex modes with the
100base-FX full and half linkmode entries.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the ability to advertise the Fiber connection if the strap or the
op-mode is configured for 100Base-FX.

Auto negotiation is not supported on this PHY when in fiber mode.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add entries for the 100base-FX full and half duplex supported modes.

$ ethtool eth0
        Supported ports: [ FIBRE ]
        Supported link modes:  100baseFX/Half 100baseFX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: No
        Supported FEC modes: Not reported
        Advertised link modes: 100baseFX/Half 100baseFX/Full
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: Not reported
        Speed: 100Mb/s
        Duplex: Full
        Auto-negotiation: off
        Port: MII
        PHYAD: 1
        Transceiver: external
        Supports Wake-on: gs
        Wake-on: d
        SecureOn password: 00:00:00:00:00:00
        Current message level: 0x00000000 (0)

        Link detected: yes
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->nh.raw has been renamed as skb->network_header in 2007, in
commit b0e380b1 ("[SK_BUFF]: unions of just one member don't get
                      anything done, kill them")

So here we change it to the new name.

Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: NXie He <xie.he.0141@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addresses the following coccinelle warning:

drivers/net/ethernet/ti/cpsw.c:1599:2-17: WARNING: Assignment of 0/1 to
bool variable
drivers/net/ethernet/ti/cpsw.c:1300:2-17: WARNING: Assignment of 0/1 to
bool variable
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NJason Yan <yanaijie@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addresses the following coccinelle warning:

drivers/net/ethernet/realtek/8139too.c:981:2-8: WARNING: Assignment of
0/1 to bool variable
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NJason Yan <yanaijie@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addresses the following coccinelle warning:

drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:15415:1-26: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:12393:2-17: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:15497:2-27: WARNING:
Assignment of 0/1 to bool variable
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NJason Yan <yanaijie@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addresses the following coccinelle warning:

drivers/net/ethernet/qlogic/qed/qed_rdma.c:1465:2-13: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/qlogic/qed/qed_rdma.c:1468:2-14: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/qlogic/qed/qed_rdma.c:1471:2-13: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/qlogic/qed/qed_rdma.c:1472:2-14: WARNING:
Assignment of 0/1 to bool variable
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NJason Yan <yanaijie@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addresses the following coccinelle warning:

drivers/net/ethernet/broadcom/b44.c:2213:6-20: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/broadcom/b44.c:2218:2-16: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/broadcom/b44.c:2226:3-17: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/broadcom/b44.c:2230:3-17: WARNING: Assignment of
0/1 to bool variable
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NJason Yan <yanaijie@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/micrel/ksz884x.c: In function rx_proc:
drivers/net/ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/micrel/ksz884x.c: In function netdev_get_ethtool_stats:
drivers/net/ethernet/micrel/ksz884x.c:6512:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]

these variable is never used, so remove it.
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/intel/e1000/e1000_hw.c: In function e1000_phy_init_script:
drivers/net/ethernet/intel/e1000/e1000_hw.c:132:6: warning: variable ‘ret_val’ set but not used [-Wunused-but-set-variable]

`ret_val` is never used, so remove it.
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/cavium/liquidio/octeon_device.c: In function lio_pci_readq:
drivers/net/ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/cavium/liquidio/octeon_device.c: In function lio_pci_writeq:
drivers/net/ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]

these variable is never used, so remove it.
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
mv88e6xxx: Add devlink regions support

Make use of devlink regions to allow read access to some of the
internal of the switches. Currently access to global1, global2 and the
ATU is provided.

The switch itself will never trigger a region snapshot, it is assumed
it is performed from user space as needed.

v2:
Remove left of debug print
Comment ATU format is generic to mv88e6xxx
Combine declaration and the assignment on a single line.

v3:
Drop support for port regions
Improve the devlink API with a priv member and passing the region to
the snapshot function
Make the helper to convert from devlink to ds an inline function

v4:
Add missing kerneldoc in ICE driver
Fix typo for global2 reading global1 registers
Make use of enum to make code more readable
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return the driver name and the asic.id with the switch name.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the DSA drivers to implement the devlink call to get info info,
e.g. driver name, firmware version, ASIC ID, etc.

v2:
Combine declaration and the assignment on a single line.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the global registers, and the ATU to be snapshot via devlink
regions. It is later planned to add support for the port registers.

v2:
Remove left over debug prints
Comment ATU format is generic for mv88e6xxx, not wider

v3:
Make use of ops structure passed to snapshot function
Remove port regions

v4:
Make use of enum mv88e6xxx_region_id
Fix global2/global1 read typ0
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor the code in mv88e6xxx_atu_new() which builds a bitmaps of
FIDs in use into a helper function. This will be reused by the devlink
code when dumping the ATU.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There will soon be more devlink code. Move the existing code into a
file of its own, before we start adding this new code.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow DSA drivers to make use of devlink regions, via simple wrappers.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Given a devlink instance, return the dsa switch it is associated to.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the region to be snapshotted to the function performing the
snapshot. This allows one function to operate on numerous regions.

v4:
Add missing kerneldoc for ICE
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver may have multiple regions which can be dumped using one
function. However, for this to work, additional information is
needed. Add a priv member to the ops structure for the driver to use
however it likes.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Felix DSA driver cleanup: build Seville separately

When introducing the Seville switch support to the Felix driver, some
technical debt was created. Since both VSC9959 and VSC9953 are embedded
switches (one on an arm64 SoC and the other on a powerpc SoC), there is
no use case for having the code for both be present in the same module.

This was necessary at the time due to the common SERDES PCS code that
they were using, but that has been since refactored into
drivers/net/pcs/pcs-lynx.c.

This makes the Seville driver stop uselessly depending upon PCI and
FSL_ENETC_MDIO, which were only dependencies of Felix in fact.

Some whitespace/tab conversions are also present in this series as part
of the cleanup process.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Seville does not need to depend on PCI or on the ENETC MDIO controller.
There will also be other compile-time differences in the future.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not only does Sevile not have a PTP clock, but with separate modules,
this structure cannot even live in felix.c, due to the .owner =
THIS_MODULE assignment causing this link time error:

drivers/net/dsa/ocelot/felix.o:(.data+0x0): undefined reference to `__this_module'
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is a good measure to ensure correctness if the structures that are
meant to remain constant are only processed by functions that thake
constant arguments.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While we don't plan on making any changes to this function, currently
this is the only remaining dependency between felix and seville, after
the PCS has been refactored out into pcs-lynx.c.

Duplicate this function in seville to break the dependency completely.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>