replace single queue function calls with equivalent multiple queue
functions. Wakeup queue and stop queue calls are guarded by spin lock.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Free SKBs allocated during multiport aggrgation setup when RX
multiport aggregation fails in the middle. With this handling
freeing SKB in mwifiex_process_int_status() for failure case
is removed.

Also handles single RX transaction failure.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Event buffers for PCIe interface are allocated during driver
initialisation, and respective physical addresses are sent to FW
in *_PCIE_DESC_DETAILS command so that FW can do DMA. These buffers
will be freed while unloading the driver. Therefore we should not
free them in event handling error path. Also we should skip next
pending events in failure case.

Also fixed 'returning -1 instead of -ENOMEM is sloppy' warnings.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mBm is passed but dBm was assumed...
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch supports Marvell chipset 88W8797 (Avastar) with
SDIO interface.

The corresponding firmware image file is located at:
"mrvl/sd8797_uapsta.bin"
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NTristan Xu <xurf@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Following compilation warning is fixed by releasing referenced BSS
structure returned by cfg80211_inform_bss().

"warning: ignoring return value of cfg80211_inform_bss,
declared with attribute warn_unused_result"

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cfg80211 stack allocates private area for driver use in
struct cfg80211_bss. It will be freed by stack in bss_release().
Driver don't need to worry about it.

In mwifiex driver, we use the private area just to store band
information(u8). We don't allocate memory explicitly and store
it's pointer in bss->priv. Hence we don't have any cleanup work
to do in free_priv handler. Currently we try to free the allocated
private area in free_priv handler which is not correct.

This patch removes unnecessary free_priv handler.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Following three warnings are fixed:

>init.c +256 mwifiex_init_adapter(71)
>warn: variable dereferenced before check 'adapter->sleep_cfm'
>(see line 191)

>sta_rx.c +193 mwifiex_process_sta_rx_packet(75)
>warn: variable dereferenced before check 'priv' (see line 182)
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename DataRate to data_rate and arrange 'for' loop
for better readability.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Functions mwifiex_11n_dispatch_pkt_until_start_win and
mwifiex_11n_scan_and_dispatch used to always return value
zero for all inputs. Changing these functions to void.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use existing helper function mwifiex_fill_cap_info to fill
the HT CAP info for ibss beacons.

Also removing extra parenthesis block for better readability.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A local variable is used to calculate ht_cap_info.
Erroneously ht_cap.cap_info isn't updated in the ibss beacons
after the calculation. This patch fixes it.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware expects 'max_ssid_length' field in
'struct mwifiex_ie_types_wildcard_ssid_params' to be '0' for
performing SSID specific scan. Currently driver updates it with
an actual SSID length. Hence UUT is not able to find the AP
configured in hidden SSID mode in scan results and association
fails.

max_ssid_length is filled with '0' to fix the issue.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Probably we never hit this condition, but in case we do, we may as
well put a return here instead of just printing a warning message and
then corrupting memory.  The caller doesn't check the return code.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By default SDIO multiport aggregation is disabled. It's useful to
get good throughput results. This patch enables it.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We dereference adapter in the error handling code so this needed to
be fixed.  This function is always called like:
	adapter->if_ops.host_to_card(adapter, ...);
so adapter can never be NULL and I've removed the NULL check.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The previous if statement means this that pointer is NULL so there
is no need to free it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If kmemdup() fails we leak the memory allocated to bss_desc.
This patch fixes the leak.
I also removed the pointless default assignment of 'NULL' to 'bss_desc'
while I was there anyway.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Reviewed-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch takes care of warnings found by running
'make namespacecheck':

1. Remove dead code.
2. Reorder function definitions to avoid forward declarations.
3. Remove unnecessary function/structure declarations and mark
   them as static.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently global wait condition (adapter->cmd_wait_q.condition)
is used while sending synchronous commands to FW. When two threads
enter in mwifiex_send_cmd_sync() routine at the same time, both the
threads wait for their command responses. Since wait condition is
same for both, they wake up simultaneously after getting response
of 1st command. After this when a thread is waiting for command
response of 3rd command, it wakes up after getting response of 2nd
command and so on. Therefore we don't wait for the response of last
command(0xaa) during unload. Hence while next time loading the driver
command time out is seen for INIT command.

This problem is resolved by having separate wait condition flag for
each command(except scan command). Since scan command is treated
differently (by maintaining scan pending q etc.), newly defined flag
(scan_wait_q_woken) is used as a scan wait condition.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch supports 88W8766P chipset with a PCIe interface.

The corresponding firmware image file is located at:
"mrvl/pcie8766_uapsta.bin"
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NRamesh Radhakrishnan <rramesh@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/mwifiex/main.c +828 mwifiex_remove_card(52)
  error: potential null derefence 'priv'.
drivers/net/wireless/mwifiex/main.c +828 mwifiex_remove_card(52)
  error: we previously assumed 'priv' could be null (see line 820)
drivers/net/wireless/mwifiex/txrx.c +90 mwifiex_process_tx(24)
  error: potential null derefence 'local_tx_pd'.
drivers/net/wireless/mwifiex/sta_ioctl.c +766
mwifiex_rate_ioctl_set_rate_value(30)
  error: buffer overflow 'rate' 14 <= 14

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In failure case locks are not allocated in mwifiex_register().
So mwifiex_free_lock_list() routine call becomes redundant.
Also we don't need to check return type for mwifiex_init_lock_list()
routine. It never fails.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "mwifiex: remove list traversal.."(fcf2176c..)
wrongly modifies AMSDU aggregation check. Due to this even though
packet size for iperf traffic is already large, we unnecessarily
try to aggregate them which adds some delay. If Tx iperf is started
on UUT for 30 seconds, UUT keeps sending Tx packets for few more
seconds.

That commit is reverted to fix the problem.
Also, MIN_NUM_AMSDU check is moved inside the loop to optimize the
loop.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Making adding and deleting virtual interfaces dynamic. Adding
handlers for creating and deleting virtual interface with
given name and dev respectively.

Also, creating default interface of type station on insmod of
the driver.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"iw dev mlan0 link" shows wrong data rate, because data rate is
not sent properly to cfg80211 stack. Also stack is not updated
with mcs and Tx data flags information.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In disconnected state "iw dev mlan0 link" command will return
from cfg80211 stack itself. We also have an error check in
mwifiex_cfg80211_get_station() routine. Therefore the code
under "if (!priv->media_connected)" condition in
mwifiex_rate_ioctl_get_rate_value() routine becomes unreachable.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An extra call to mwifiex_dump_station_info() routine in get_station
callback function is redundant
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After handling command response, cmd skb is inserted into command
free queue(which keeps track of availabile skbs) for reuse purpose.
Skb length is not getting reset to zero here. This patch takes care
of it.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_channel_to_frequency() routine expects band parameter in
the form of "enum ieee80211_band band". Currently driver specific
band (BAND_A, BAND_AN etc.) is passed to the routine.

This patch makes sure that correct parameter is passed.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In recent commit "mwifiex: use cfg80211 dynamic scan..."
(7c6fa2a8..) scan table handling in driver is removed to
make use of cfg80211 dynamic scan table. Now driver sends
beacon buffers found in scanning directly to stack and parse
the buffer for requested BSS only during association.

Beacon buffer doesn't contain bss band information. Driver
gets it from firmware in separate tlv (chan_band_tlv).
Currently since we don't inform stack about bss bandinfo,
there is an issue with 5GHz association.

Use "priv" field of struct cfg80211_bss to store bandinfo.
This fixes 5GHz association issue.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes association in 5GHz doesn't work. Dmesg log shows
"Can not find requested SSID xyz" error message. Currently
while preparing scan channel list for firmware Null entries
are created for disabled channels. The routine which retrieves
this list ignores channels after Null entry. Hence sometimes
driver doesn't scan the channel of requested AP and association
fails. The issue is fixed by avoiding those NULL entries.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We dereference "rate" on the lines before so the checks here are too
late to help.  This function is only called from
mwifiex_dump_station_info() and "rate" is always a non-NULL pointer
so the check can be removed.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We're not likely to hit this small memory leak, but lets fix it
anyway to keep the static checkers happy.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sequence of kmalloc/kzalloc and memcpy is replaced with
kmemdup.

Cc: Walter Harms <wharms@bfs.de>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Test the just-initialized value rather than some other one.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier x,y,f!={PTR_ERR,ERR_PTR,ERR_CAST};
statement S;
@@

x = f(...);
(
if (\(x == NULL\|IS_ERR(x)\)) S
|
*if (\(y == NULL\|IS_ERR(y)\))
 { ... when != x
   return ...; }
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of maintaining static scan table in driver, scan list is sent
to cfg80211 stack (after parsing each scan command response).
In assoc handler (for infra and ibss network) requested BSS information
is retrieved using cfg80211_get_bss() API.

With the changes above some redundant code are removed.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add code to display driver version information in dmesg after
loading the driver successfully.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mwifiex_get_bss_info() routine updates variable 'info->scan_table_idx'
but it is never used.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>