The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NSteven King <sfking@fdwdc.com>

Enable Coldfire QSPI support when SPI_COLDFIRE_QSPI is built as a module.

This version of the patch combines changes to the config files and  device.c
and uses IF_ENABLED (thanks to Sam Ravnborg for the suggestion).
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Most of the more modern ColdFire cores use the same code to reset the CPU
(but it is different to most of the earlier cores). Currently that is
duplicated in each of the sub-arch files. Pull out this common code and
out a single copy of it with the other common reset code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

We can move all the init calls in the initcall code into the more general
arch setup code (which is config_BSP() here). That makes the 532x consistent
with other ColdFire CPUs setup code. It means we can get rid of the initcall
setup here all together. Also make sure we set the arch mach_reset function
pointer to get the local arch reset code called on reset.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire QSPI is common to quite a few ColdFire CPUs. No need to duplicate
its platform setup code for every CPU family member that has it. Merge all the
setup code into a single shared file.

This also results in few platforms no longer needing any local platform
setup code. In those cases remove the empty devices array and initcall
code as well.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

If we make all QSPI (SPI protocol) addressing consistent across all ColdFire
family members then we will be able to remove the duplicated plaform data
and code and use a single setup for all.

So modify the ColdFire 532x QSPI addressing so that:

. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
. move chip select definitions (CS) to appropriate header
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire FEC is common to quite a few ColdFire CPUs. No need to duplicate
its platform setup code for every CPU family member that has it. Merge all the
setup code into a single shared file.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

If we make all FEC (ethernet) addressing consistent across all ColdFire
family members then we will be able to remove the duplicated plaform data
and use a single setup for all.

So modify the ColdFire 532x FEC addressing so that:

. FECs are numbered from 0 up
. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire UART is common to all ColdFire CPU's. No need to duplicate
its platform setup code for every CPU family member. Merge all the setup
code into a single shared file.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Simplify the UART setup code so that it no longer loops for each UART
present. Just make it do all the work it needs in a single function.
This will make the code easier to share when we move to a single set
of platform data for ColdFire UARTs.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

If we make all UART addressing consistent across all ColdFire family members
then we will be able to remove the duplicated plaform data and use a single
setup for all.

So modify the ColdFire 532x UART addressing so that:

. UARTs are numbered from 0 up
. use a common name for IRQs used
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

With a few small changes we can make the m68knommu timer init code the
same as the m68k code. By using the mach_sched_init function pointer
and reworking the current timer initializers to keep track of the common
m68k timer_interrupt() handler we end up with almost identical code for
m68knommu.

This will allow us to more easily merge the mmu and non-mmu m68k time.c
in future patches.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

There is a lot of common code that could be shared between the m68k
and m68knommu arch branches. It makes sense to merge the two branches
into a single directory structure so that we can more easily share
that common code.

This is a brute force merge, based on a script from Stephen King
<sfking@fdwdc.com>, which was originally written by Arnd Bergmann
<arnd@arndb.de>.

> The script was inspired by the script Sam Ravnborg used to merge the
> includes from m68knommu. For those files common to both arches but
> differing in content, the m68k version of the file is renamed to
> <file>_mm.<ext> and the m68knommu version of the file is moved into the
> corresponding m68k directory and renamed <file>_no.<ext> and a small
> wrapper file <file>.<ext> is used to select between the two version. Files
> that are common to both but don't differ are removed from the m68knommu
> tree and files and directories that are unique to the m68knommu tree are
> moved to the m68k tree. Finally, the arch/m68knommu tree is removed.
>
> To select between the the versions of the files, the wrapper uses
>
> #ifdef CONFIG_MMU
> #include <file>_mm.<ext>
> #else
> #include <file>_no.<ext>
> #endif

On top of this file merge I have done a simplistic merge of m68k and
m68knommu Kconfig, which primarily attempts to keep existing options and
menus in place. Other than a handful of options being moved it produces
identical .config outputs on m68k and m68knommu targets I tested it on.

With this in place there is now quite a bit of scope for merge cleanups
in future patches.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Since Grant has added the coldfire-qspi driver to next-spi, here is the
platform support for the parts that have qspi hardware.  This sets up
gpio to do the spi chip select using the default chip select pins; it should
be trivial for boards that require different or additional spi chip selects to
use other gpios as needed.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The newer ColdFire 532x family of CPU's uses the old timer, but has a
newer interrupt controller. It doesn't need the special timer setup
that was required when using the older interrupt controller. Remove the
dead timer irq and level setting code, and define the hard coded vector.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

With fully implemented interrupt controller code we don't need to do
the custom interrupt setup for the timer device of the ColdFire 532x.
Remove that code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

With the common intc-simr interrupt controller code in place the ColdFire
532x family startup code can be greatly simplified. Remove all the
interrupt masking code, and the per-device interrupt config here.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add support for the 532x.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

m68knommu: add FEC platform support to ColdFire CPU's setup code

Move the per-CPU FEC driver setup code into the actual platform
setup code for each ColdFire CPU varient.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5329 ColdFire peripheral IO register addresses are not relative to
the MBAR register. So fix the serial platform setup array and IRQ acking
to use just the direct addresses.
Signed-off-by: NMatt Waddel <Matt.Waddel@freescale.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Remove all the dead timer interrupt checking functions for the ColdFire
CPU "timers" hardware that are not used after switching to GENERIC_TIME.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Switch to platform style configuration for 532x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reduce the function pointer mess of the m68knommu timer code by calling
directly to the local hardware's timer setup, and expose the local
common timer interrupt handler to the lower level hardware timer.

Ultimately this will save definitions of all these functions across all
the platform code to setup the function pointers (which for any given
m68knommu CPU family member can be only one set of hardware timer
functions).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The switch to using the generic irq framework removed the
coldfire_trap_init() code, so remove all references to it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently most of the m68knommu cpu/board setup files are handling
the setup of fixed boot parameters (via CONFIG_BOOTPARAM) themselves.
Move all this into the common setup code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use irq_handler_t for passing clock handler routine around.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kbuild explicitly includes this at build time.
Signed-off-by: NDave Jones <davej@redhat.com>

Add kernel startup code for the new Freescale 532x CPU family.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>