Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 19 8月, 2017 3 次提交
  3. 16 8月, 2017 2 次提交
  5. 21 6月, 2017 1 次提交
  7. 07 6月, 2017 1 次提交
  9. 12 5月, 2017 1 次提交
    • J
      s390/qeth: unbreak OSM and OSN support · 2d2ebb3e
      由 Julian Wiedmann 提交于 
      commit b4d72c08 ("qeth: bridgeport support - basic control")
broke the support for OSM and OSN devices as follows:

As OSM and OSN are L2 only, qeth_core_probe_device() does an early
setup by loading the l2 discipline and calling qeth_l2_probe_device().
In this context, adding the l2-specific bridgeport sysfs attributes
via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c,
since the basic sysfs infrastructure for the device hasn't been
established yet.

Note that OSN actually has its own unique sysfs attributes
(qeth_osn_devtype), so the additional attributes shouldn't be created
at all.
For OSM, add a new qeth_l2_devtype that contains all the common
and l2-specific sysfs attributes.
When qeth_core_probe_device() does early setup for OSM or OSN, assign
the corresponding devtype so that the ccwgroup probe code creates the
full set of sysfs attributes.
This allows us to skip qeth_l2_create_device_attributes() in case
of an early setup.

Any device that can't do early setup will initially have only the
generic sysfs attributes, and when it's probed later
qeth_l2_probe_device() adds the l2-specific attributes.

If an early-setup device is removed (by calling ccwgroup_ungroup()),
device_unregister() will - using the devtype - delete the
l2-specific attributes before qeth_l2_remove_device() is called.
So make sure to not remove them twice.

What complicates the issue is that qeth_l2_probe_device() and
qeth_l2_remove_device() is also called on a device when its
layer2 attribute changes (ie. its layer mode is switched).
For early-setup devices this wouldn't work properly - we wouldn't
remove the l2-specific attributes when switching to L3.
But switching the layer mode doesn't actually make any sense;
we already decided that the device can only operate in L2!
So just refuse to switch the layer mode on such devices. Note that
OSN doesn't have a layer2 attribute, so we only need to special-case
OSM.

Based on an initial patch by Ursula Braun.

Fixes: b4d72c08 ("qeth: bridgeport support - basic control")
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2d2ebb3e
  11. 12 4月, 2017 7 次提交
  13. 07 4月, 2017 3 次提交
  15. 25 3月, 2017 1 次提交
    • J
      s390/qeth: size calculation outbound buffers · 7d969d2e
      由 Julian Wiedmann 提交于 
      Depending on the device type, hard_start_xmit() builds different output
buffer formats. For instance with HiperSockets, on both L2 and L3 we
strip the ETH header from the skb - L3 doesn't need it, and L2 carries
it in the buffer's header element.
For this, we pass data_offset = ETH_HLEN all the way down to
__qeth_fill_buffer(), where skb->data is then adjusted accordingly.
But the initial size calculation still considers the *full* skb length
(including the ETH header). So qeth_get_elements_no() can erroneously
reject a skb as too big, even though it would actually fit into an
output buffer once the ETH header has been trimmed off later.

Fix this by passing an additional offset to qeth_get_elements_no(),
that indicates where in the skb the on-wire data actually begins.
Since the current code uses data_offset=-1 for some special handling
on OSA, we need to clamp data_offset to 0...

On HiperSockets this helps when sending ~MTU-size skbs with weird page
alignment. No change for OSA or AF_IUCV.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7d969d2e
  17. 12 1月, 2017 3 次提交
  19. 16 9月, 2016 1 次提交
    • H
      qeth: restore device features after recovery · e830baa9
      由 Hans Wippel 提交于 
      After device recovery, only a basic set of network device features is
enabled on the device. If features like checksum offloading or TSO were
enabled by the user before the recovery, this results in a mismatch
between the network device features, that the kernel assumes to be
enabled on the device, and the features actually enabled on the device.

This patch tries to restore previously set features, that require
changes on the device, after the recovery of a device. In case of an
error, the network device's features are changed to contain only the
features that are actually turned on.
Signed-off-by: NHans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e830baa9
  21. 17 6月, 2016 5 次提交
  23. 15 12月, 2015 1 次提交
  25. 07 10月, 2015 1 次提交
  27. 22 9月, 2015 2 次提交
  29. 19 5月, 2015 1 次提交
  31. 18 1月, 2015 1 次提交
  33. 27 10月, 2014 1 次提交
  35. 03 9月, 2014 1 次提交
  37. 22 7月, 2014 3 次提交
  39. 29 4月, 2014 1 次提交