Currently ARCH_BCM has been used for Broadcom
Mobile V7 based SoCs. In order to allow other Broadcom
SoCs to also use mach-bcm directory and files, this patch
renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing
in mach-bcm directory.
Signed-off-by: NChristian Daudt <bcm@fixthebug.org>
Acked-by: NOlof Johansson <olof@lixom.net>

Changes from v2:
 - switch ARCH_MULTIPLATFORM from select to depends
 - remove 'default y' from BCM_MOBILE

Changes from v1:
 - fix alpha ordering in dts/Makefile
 - break into 4 patches for separate subsys

Turn on the bcm281xx GPIO driver in the kernel configuration.
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Reviewed-by: NChristian Daudt <csd@broadcom.com>

Turning on the L2 cache for the bcm281xx family.
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Acked-by: NChristian Daudt <csd@broadcom.com>

This adds support for the Broadcom timer, used in the following SoCs:
BCM11130, BCM11140, BCM11351, BCM28145, BCM28155

Updates from V6:
- Split DT portion into a separate patch

Updates from V5:
- Rebase to latest arm-soc/for-next

Updates from V4:
- Switch code to use CLOCKSOURCE_OF_DECLARE

Updates from V3:
- Migrate to 3.9 timer framework updates

Updates from V2:
- prepend static fns + fields with kona_

Updates from V1:
- Rename bcm_timer.c to bcm_kona_timer.c
- Pull .h into bcm_kona_timer.c
- Make timers static
- Clean up comment block
- Switched to using clockevents_config_and_register
- Added an error to the get_timer loop if it repeats too much
- Added to Documentation/devicetree/bindings/arm/bcm/bcm,kona-timer.txt
- Added missing readl to timer_disable_and_clear

Note: bcm,kona-timer was kept as the 'compatible' field to make it
specific enough for when there are multiple bcm timers (bcm,timer is
too generic).
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJohn Stultz <john.stultz@linaro.org>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

In drivers/gpio/Kcong, ARCH_REQUIRE_GPIOLIB selects GPIOLIB which in
turn selects GENERIC_GPIO.  So GENERIC_GPIO will be selected
automatically for those platforms that select ARCH_REQUIRE_GPIOLIB.

Remove the redundant 'select GENERIC_GPIO' for platforms that already
select ARCH_REQUIRE_GPIOLIB at either mach or plat level.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

In order to start upstreaming Broadcom SoC support, create
a starting hierarchy, arch and dts files.
The first support SoC family that is planned is the
BCM281XX (BCM11130/11140/11351/28145/28155) family of dual A9 mobile
SoC cores.
This code is just the skeleton code for get the machine upstreamed. It
has been made MULTIPLATFORM compatible.
Next steps
----------
Upstream a basic set of drivers - sufficient for a console boot to
ramdisk. These will includer timer, gpio, i2c drivers.
After this basic set, we will proceed with a more comprehensive set
of drivers for the 281XX SoC family.

v2 patch mods
--------
 - Remove l2x0_of_init call as there were problems with the code.
   A separate patch will be submitted with cache init code
 - Rename capri files and refs to bcm281xx-based names
 - Add bcm281xx binding doc
 - various misc cleanups

v3 patch mods
-------------
 - Remove extra #include lines
 - Remove remaining references to capri
 - dt uart chipset string added
 - cleaned up chip # references

v4 patch mods
-------------
 - swap order of compatible definitions for uart
 - fix typo

v5 patch mods
-------------
 - Rename bcm281xx to bcm11351 in dts+code,
   leaving references to bcm281xx only in help+comments.

v6 patch mods
-------------
 - fix typo in uart 'compatible' string
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>