The device.h header was including module.h, making it present for
most of these drivers.  But we want to clean that up.  Call out the
include of module.h in the modular network drivers.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.

The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
	ops.conf_tx = conf_tx_op;

@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
	conf_tx_op (
-		struct ieee80211_hw *hw,
+		struct ieee80211_hw *hw, struct ieee80211_vif *vif,
		u16 queue,
		const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.

Update all the drivers that implement these callbacks.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver for the RTL8187L chips returns IEEE80211_TX_STAT_ACK for all
packets, even if the maximum number of retries was exhausted. In addition
it fails to setup max_rates in the ieee80211_hw struct, This behavior
may be responsible for the problems noted in Bug 14168. As the bug is very
old, testers have not been found, and I do not have the case where the
indicated signal is less than -70 dBm.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).

Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.

Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These drivers share one header file, but nothing else.  Worse, both
drivers use the rtl8225 part with different register settings.  The
results has been some ugly naming -- let's simplify that.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>

Current 8187B initialization misses anaparam registers restore after
8187 reset. This causes ANAPARAM register to stay zeroed out (ANAPARAM2
kept its value on my tests). To avoid this, call rtl8187_set_anaparam
right after chip reset (to be on the safe side, as it makes sure we
restore all ANAPARAM registers).
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: seno <senada@t-online.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Usually you set RTL818X_CONFIG3_ANAPARAM_WRITE when you are going to
change/write ANAPARAM registers. But in current initialization of
RTL8187B there is a place where ANAPARAM_WRITE bit is set without any
ANAPARAM register being written, without reason, so remove it.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: seno <senada@t-online.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are repeated calls for anaparam on/off sequence in the code.
Consolidate the common code in rtl8187_set_anaparam and use it where
needed.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The GNTSel bit should only concern pci devices by looking at RTL8180
spec, which is not the case of 8187B. Also testing shows that trying to
set this bit fails, a subsequent read from the register after trying to
set it shows that the bit isn't set, seems the hardware ignores it,
which makes sense. This setting was a left over from Realtek sources.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On 8187B start, comment about pll reset, and move it out of ANAPARAM
write sequence, so that code is more readable.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The table with misc register initialization was setting it, and later
on we would set it again with a explicity call to rtl818x_iowrite16_idx.

Remove duplicate initialization from the register table.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were using wrong address for BRSR (Basic Rate Set Register) while
initializing its value, comparing with Realtek sources, for 8187B case.

Also, the same register is initialized in rtl8187b_reg_table, so remove
the duplicate initialization from the table.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On 8187B path, we set a initial value for beacon interval and atim
window on initialization. But this isn't needed, since same setup is
done on rtl8187_config.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes redundant write to Auto Rate Fallback Register on RTL8187B.
The same value was being written twice in the same function. Avoid this
removing the duplicate initialization on rtl8187b_reg_table, and also
add comment for this write (information from Realtek source).
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clearing the per packet TX AGC for the RTL8187B device appears to
increase its overall TX power. This allows the device to associate and a
connection to be established using APs a little further away.

This is in accordance to what is done for RTL8187L devices and also what
Realtek drivers do.
Tested-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: linux-wireless@vger.kernel.org
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Rogerio Luz Coelho <rogluz.news@gmail.com>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Hin-Tak Leung <hintak.leung@gmail.com>
Cc: seno <senada@t-online.de>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit c96c31e4
"(drivers/net/wireless: Use wiphy_<level>)"
inadvertently changed some upper case words to
lower case.  Restore the original case.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Standardize the logging macros used.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>

Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

Add new RTL8187B device.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:

@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is checked in add_interface, but there it is easily replaced with
a check of priv->vif.  If that information should become necessary,
it is available in vif->type anyway.

It is also checked in led_turn_on and led_turn_off, where I made the
substitutions as described above.  Of course, these checks seem to
have been incorrect since the driver was using NL80211_IFTYPE_MONITOR
to indicate no interface rather than NL80211_IFTYPE_UNSPECIFIED.
Anyway, I think these checks may be extraneous...?
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.

This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: NAntti Kaijanmäki <antti@kaijanmaki.net>
Tested-by: NHin-Tak Leung <hintak.leung@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The qual member of ieee80211_rx_status is deprecated. As a result, this
driver no longer needs to calculate a quality value.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change implements rfkill support for RTL8187B and RTL8187L devices,
using new cfg80211 rfkill API.
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Larry Finger reports following lockdep warning:

[ INFO: possible circular locking dependency detected ]
2.6.31-rc6-wl #201
-------------------------------------------------------
rfkill/30578 is trying to acquire lock:
 (&(&priv->work)->work#2){+.+...}, at: [<ffffffff81051215>]
__cancel_work_timer+0xd9/0x222

but task is already holding lock:
 (&priv->conf_mutex#2){+.+.+.}, at: [<ffffffffa064a024>]
rtl8187_stop+0x31/0x364 [rtl8187]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&priv->conf_mutex#2){+.+.+.}:
       [<ffffffff81065957>] __lock_acquire+0x12d0/0x1614
       [<ffffffff81065d54>] lock_acquire+0xb9/0xdd
       [<ffffffff8127c32f>] mutex_lock_nested+0x56/0x2a8
       [<ffffffffa064a392>] rtl8187_work+0x3b/0xf2 [rtl8187]
       [<ffffffff81050758>] worker_thread+0x1fa/0x30a
       [<ffffffff81054ca5>] kthread+0x8f/0x97
       [<ffffffff8100cb7a>] child_rip+0xa/0x20
       [<ffffffffffffffff>] 0xffffffffffffffff

-> #0 (&(&priv->work)->work#2){+.+...}:
       [<ffffffff8106568c>] __lock_acquire+0x1005/0x1614
       [<ffffffff81065d54>] lock_acquire+0xb9/0xdd
       [<ffffffff8105124e>] __cancel_work_timer+0x112/0x222
       [<ffffffff8105136b>] cancel_delayed_work_sync+0xd/0xf
       [<ffffffffa064a33f>] rtl8187_stop+0x34c/0x364 [rtl8187]
       [<ffffffffa0242866>] ieee80211_stop_device+0x29/0x61 [mac80211]
       [<ffffffffa0239194>] ieee80211_stop+0x476/0x530 [mac80211]
       [<ffffffff8120ce15>] dev_close+0x8a/0xac
       [<ffffffffa01d9fa7>] cfg80211_rfkill_set_block+0x4a/0x7a [cfg80211]
       [<ffffffffa01bf4f0>] rfkill_set_block+0x84/0xd9 [rfkill]
       [<ffffffffa01bfc31>] rfkill_fop_write+0xda/0x124 [rfkill]
       [<ffffffff810cf286>] vfs_write+0xae/0x14a
       [<ffffffff810cf3e6>] sys_write+0x47/0x6e
       [<ffffffff8100ba6b>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

The problem here is that rtl8187_stop, while helding priv->conf_mutex,
runs cancel_delayed_work_sync on an workqueue that runs rtl8187_work,
which also takes priv->conf_mutex lock. Move cancel_delayed_work_sync
out of rtl8187_stop priv->conf_mutex locking region.
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RTL8187B always needs MSR_LINK_ENEDCA flag to be set even when it is in
no link mode, otherwise it'll not be able to associate when this flag is
not set after the change "mac80211: fix managed mode BSSID handling".

By accident, setting BSSID of AP before association makes 8187B to
successfuly associate even when ENEDCA flag isn't set, which was the
case before the mac80211 change. But now the BSSID of AP we are trying
to associate is only available after association is successful, and
any attempt to associate without the needed flag doesn't work.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.

A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.

We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:

  * ieee80211_queue_work()
  * ieee80211_queue_delayed_work()

These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.

Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

http://bugzilla.kernel.org/show_bug.cgi?id=13383Reported-by: NPrzemyslaw Kulczycki <azrael@autocom.pl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

First of all, it exposes the SKB list implementation.

Second of all it's not needed.  If we get called here, we
successfully enqueued the URB with the linked SKB and
such a completion only gets called one time on such an
SKB.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The following patch implements some control over the LED on RTL8187B and
RTL8187L devices. Triggers are registered for TX and RX. Whenever the
trigger event occurs, the LED is turned off for 1/20 second, then turned
back on.

Note: For those RTL8187X devices that are built into the computer and have
a LED that is expected to be controlled with a radio switch, this patch will
not operate that LED. That will take a separate patch to be prepared later.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>